BeamZ SLIMPAR 30 LED PAR Projector

1. مقدمه

ممنون از خریدتونasing the BeamZ SLIMPAR 30 LED PAR Projector. This compact and powerful lighting fixture is designed for a variety of applications, from stage lighting to architectural uplighting. It features 6 high-power 3W RGB LEDs, offering vibrant color mixing and a range of dynamic effects. This manual provides essential information for safe operation, setup, and maintenance of your device.

Key features include DMX control, multiple pre-programmed shows, sound-activated mode with adjustable sensitivity, and an auto mode with adjustable speed. Its robust design and versatile functionality make it an ideal choice for DJs, bands, event organizers, and venues.

Image 1.1: The BeamZ SLIMPAR 30 LED PAR Projector, showcasing its compact design and six bright green LEDs.

2. دستورالعمل های ایمنی

هشدار: To reduce the risk of electric shock, do not open this unit. There are no user-serviceable parts inside. Refer all servicing to qualified service personnel.

• Read this manual thoroughly before operating the unit.
• این راهنما را برای مراجعات بعدی نگه دارید.
• همیشه دستگاه را به پریز برق دارای اتصال زمین وصل کنید.
• Disconnect from mains power before cleaning or servicing.
• دستگاه را در معرض باران یا رطوبت قرار ندهید.
• از تهویه مناسب در اطراف دستگاه اطمینان حاصل کنید.
• Do not look directly into the light source when the unit is on.
• فقط از جلد مشخص شده استفاده کنیدtage (230Vac / 50Hz).

3. محتویات بسته

Upon opening the box, ensure all items listed below are present and in good condition:

• 1x BeamZ SLIMPAR 30 LED PAR Projector
• 1x Double Mounting Bracket
• 1 عدد کابل برق
• ۱ عدد دفترچه راهنمای کاربر (این سند)
• 1x IRC Remote Control (if included with your specific package)

در صورت مفقود شدن یا آسیب دیدن اقلام، لطفاً فوراً با فروشنده خود تماس بگیرید.

4. راه اندازی

4.1 نصب

The SLIMPAR 30 comes with a double mounting bracket for versatile positioning. It can be placed on a flat surface, mounted to a truss using a clamp (not included), or attached to a wall/ceiling.

• Ensure the mounting surface or truss can support the weight of the fixture.
• Always use a safety cable when mounting overhead.
• Adjust the bracket to the desired angle and secure it with the locking knobs.

4.2 اتصال برق

Connect the supplied power cable to the power input on the rear of the unit and then to a suitable 230Vac / 50Hz grounded power outlet.

۵.۳ اتصال DMX (اختیاری)

For DMX control, connect a 3-pin XLR DMX cable from your DMX controller's output to the DMX IN port of the SLIMPAR 30. For multiple units, daisy-chain them by connecting the DMX OUT of the first unit to the DMX IN of the next, and so on.

تصویر 4.1: عقب view of the BeamZ SLIMPAR 30, showing the control panel with LED display, DMX input/output, and power connection.

5. عملیاتی

5.1 کنترل پنل به پایان رسیدview

The SLIMPAR 30 features a 4-digit LED display and four control buttons on its rear panel:

• منو: بین گزینه‌های منوی اصلی جابه‌جا می‌شود.
• بالا پایین: در زیرمنوها پیمایش می‌کند یا مقادیر پارامترها را تنظیم می‌کند.
• وارد: گزینه یا مقدار انتخاب شده را تأیید می‌کند.

5.2 حالت عملیاتی

The SLIMPAR 30 offers several operating modes:

• حالت DMX: Allows control via an external DMX controller. Select the desired DMX channel mode (3, 4, or 7 channels) and set the DMX address.
• حالت خودکار: The unit runs through pre-programmed light shows automatically. Speed can be adjusted.
• حالت فعال صدا: The light shows react to music or sound detected by the built-in microphone. Sensitivity can be adjusted.
• حالت Master/Slave: Link multiple SLIMPAR 30 units together. One unit acts as the master, controlling all other slave units.
• حالت رنگ دستی: Allows direct selection of static colors or manual mixing of RGB values.

Image 5.1: Visual representation of the BeamZ SLIMPAR 30's pre-programmed shows and auto mode with adjustable speed, demonstrating dynamic lighting effects.

Image 5.2: The BeamZ SLIMPAR 30 demonstrating its ability to produce various colored lighting effects, suitable for different event atmospheres.

Image 5.3: The BeamZ SLIMPAR 30 effectively illuminating a room, showcasing its suitability for architectural and event lighting.

5.3 Remote Control (IRC)

If your package includes the IRC remote control, you can conveniently operate the SLIMPAR 30 from a distance. The remote allows access to various functions such as mode selection (Auto, Sound, DMX), color selection, strobe, and blackout.

Image 5.4: The IRC remote control for the BeamZ SLIMPAR 30, showing buttons for various functions like auto mode, sound mode, DMX, color selection, and strobe.

6. تعمیر و نگهداری

6.1 تمیز کردن

Regular cleaning helps maintain optimal light output and extends the lifespan of the unit.

• Always disconnect the unit from power before cleaning.
• برای پاک کردن قسمت بیرونی از یک پارچه نرم و بدون پرز استفاده کنیدasing.
• Clean the lens regularly with a soft cloth and a mild glass cleaner to ensure clear light projection.
• از پاک کننده ها یا حلال های ساینده استفاده نکنید.

6.2 ذخیره سازی

When not in use, store the unit in a dry, dust-free environment, preferably in its original packaging or a suitable carrying case.

7 عیب یابی

If the problem persists after trying these solutions, please contact BeamZ customer support or your dealer.

8. مشخصات

9. گارانتی و پشتیبانی

This product is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or contact your local dealer.

For technical support, troubleshooting assistance, or spare parts, please contact your authorized BeamZ dealer or visit the official BeamZ webسایت برای اطلاعات تماس

لطفاً رسید خرید خود را برای هرگونه ادعای گارانتی نگه دارید.