کیت ANENG Pro ST184 Clamp دفترچه راهنمای کاربر دستگاه تست باتری و باتری متر BT173

1. مقدمه

The ANENG Pro Kit combines two essential electrical testing tools: the ST184 Smart AC Clamp Meter and the BT173 Battery Detector. This kit is designed for both professional electricians and DIY enthusiasts, offering a wide range of measurement capabilities for various electronic components and battery types. The ST184 clamp meter provides precise measurements for AC/DC voltage, AC current, resistance, capacitance, frequency, and temperature, along with non-contact voltage (NCV) detection. The BT173 battery tester offers universal compatibility for quick and accurate battery health checks without requiring external power.

Figure 1: ANENG Pro Kit ST184 Clamp Meter and BT173 Battery Tester.

2. اطلاعات ایمنی

Always observe basic safety precautions when using electrical testing equipment to reduce the risk of fire, electric shock, or personal injury. Read and understand all instructions before use.

• Ensure the device is in good working condition before each use.
• سعی نکنید حجم را اندازه گیری کنیدtagجریان‌ها یا ولتاژهایی که از حداکثر مقادیر نامی مشخص شده تجاوز می‌کنند.
• از تجهیزات حفاظت فردی مناسب (PPE) مانند عینک ایمنی و دستکش عایق استفاده کنید.
• Avoid using the device in wet conditions or in the presence of explosive gases or dust.
• For current measurements with the clamp meter, ensure only a single conductor is placed within the jaw.
• When measuring capacitance, always discharge the capacitor before connecting the test leads.
• The BT173 battery tester is powered by the battery being checked. Shorten testing time to avoid unnecessary battery depletion.

3. محصول تمام شدview

3.1. ANENG ST184 Smart AC Clamp متر

Figure 2: ANENG ST184 High Precision Clamp متر

The ST184 is a versatile clamp meter featuring a 6000-count display and automatic ranging. It is designed for non-contact measurement of AC current up to 600A, and also measures AC/DC voltage, resistance, capacitance, frequency, and temperature. Key features include True RMS for accurate readings, NCV (Non-Contact Voltage) detection for safety, a built-in flashlight for dimly lit areas, and an automatic shutdown function to conserve power.

ST184 Components:

1. Induction pliers (clamp فک)
2. Trigger for opening the jaw
3. Short press: Power on/Switch function; Long press: shutdown
4. چراغ نشانگر
5. Short Press: Lock/Unlock Data; Long press: Turn on/off backlight
6. Short press: Switch NCV; Long press: Turn on/off flashlight lighting
7. LCD high definition backlight display
8. Black watch pen negative jack input (COM)
9. Red gauge pen positive jack input (VΩHz)
10. 1.5V AAA battery compartment (requires 2 AAA batteries, not included)

Figure 3: ST184 Product Parameters and Key Features.

3.2. ANENG BT173 Battery Detector

Figure 4: ANENG BT173 Digital Display Battery Tester.

The BT173 is a high-precision battery tester designed for quick and easy assessment of various battery types. It features a dual-display screen showing both numerical voltage values and a battery level bar. The device is self-powered, meaning it does not require external batteries or a USB connection to operate. Its compact and portable design, made from durable ABS material, makes it convenient for on-the-go use.

BT173 Components:

1. 18650/21700/D type battery positive electrode contact
2. C/AA/14500 battery positive electrode contact
3. AAA/10440 battery positive electrode contact
4. N/16340 battery positive electrode contact
5. 1.55V button battery contact
6. Battery negative contact piece
7. 9V battery detection area
8. 12V/23A battery detection area
9. Battery value display (LCD)
10. Battery bar display (LCD)

Figure 5: BT173 Product Parameters and Key Features.

4. راه اندازی

4.1. جعبه گشایی و بازرسی اولیه

Upon receiving your ANENG Pro Kit, carefully open the packaging and inspect the contents. The kit typically includes:

• ST184 Clamp متر
• تستر باتری BT173
• Test leads (for ST184)
• Temperature probe (for ST184)
• User Manuals for both devices
• جعبه بسته بندی

Figure 6: ST184 Clamp Meter Accessories List.

Figure 7: BT173 Battery Tester Accessories List.

4.2. Battery Installation (ST184 Clamp متر)

The ST184 Clamp Meter requires 2 AAA batteries (not included). To install:

1. پوشش محفظه باتری را در پشت دستگاه پیدا کنید.
2. برای باز کردن درپوش از پیچ گوشتی استفاده کنید.
3. ۴ باتری AAA را وارد کنید و از قطبیت صحیح (+/-) اطمینان حاصل کنید.
4. درپوش محفظه باتری را تعویض کرده و آن را محکم کنید.

The BT173 Battery Tester does not require external batteries as it is self-powered by the battery being tested.

5. دستورالعمل های عملیاتی

5.1. ANENG ST184 Smart AC Clamp عملیات متر

The ST184 features automatic ranging, simplifying measurements. Press the power button to turn on the device. It will typically default to auto-ranging mode.

5.1.1. DC Voltage اندازه گیری

Connect the red test lead to the VΩHz jack and the black test lead to the COM jack. Touch the test leads to the positive and negative terminals of the DC voltagمنبع الکترونیکی. صفحه نمایش میزان صدا را نشان می‌دهدtage reading. Small errors may occur in common voltage تشخیص

5.1.2. Buzzer (Continuity) Measurement

سیم‌های تست را مانند ولتاژ وصل کنیدtage. Touch the test leads to the two points you want to test for continuity. If continuity is detected, the meter will emit a "drip-drip" buzzer sound, indicating a closed circuit. No buzzer will be emitted from a break point.

5.1.3. اندازه گیری مقاومت

سیم‌های تست را مانند ولتاژ وصل کنیدtage. Touch the test leads to both ends of the resistor. The display will show the resistance value in Ohms (Ω), Kilohms (kΩ), or Megohms (MΩ).

5.1.4. اندازه گیری ظرفیت

سیم‌های تست را مانند ولتاژ وصل کنیدtage. Important: Discharge the capacitor completely before measurement. Touch the test leads to the capacitor terminals. The display will show the capacitance value in Farads (F), microFarads (µF), or nanoFarads (nF).

5.1.5. اندازه گیری دما

Connect the temperature probe to the VΩHz and COM jacks. Place the tip of the temperature probe in contact with the object whose temperature you wish to measure. The display will show the real-time temperature in Celsius (°C) or Fahrenheit (°F).

۵.۳ اندازه‌گیری جریان AC (Cl)amp عملکرد)

برای اندازه گیری جریان AC، cl را باز کنیدamp jaw using the trigger. Place only a single live wire (not the entire power cord with multiple wires) inside the jaw. The display will show the AC current reading in Amperes (A). The 3.8cm jaw is suitable for a variety of wires.

Figure 8: Correct method for AC current measurement using the clamp تابع

توجه: Small currents lower than 0.6A cannot be measured accurately. If the current size is not known, the maximum range should be selected, and then the range should be appropriately reduced according to the value, but the range cannot be converted during measurement.

5.1.7. AC Voltage اندازه گیری

Connect the red test lead to the VΩHz jack and the black test lead to the COM jack. Insert the watch pen into the hole of the AC outlet to measure. The display will show the AC voltage خواندن

5.1.8. Hertz (Frequency) Measurement

سیم‌های تست را مانند ولتاژ وصل کنیدtage. Insert the watch pen into the hole of the AC outlet. The display will show the frequency in Hertz (Hz).

5.1.9. NCV (جلد غیر تماسیtage) Tests

Press the NCV button to activate non-contact voltage detection. Bring the top of the clamp meter close to a live wire or outlet. When voltage is detected, the screen will display a signal (e.g., 'EF') and emit a beeping sound. The sensor needs to be close to the measured wire (usually ≤ 2cm) and aligned with the direction of the electric field. If it is covered with metal/aluminum foil shielding or too thick insulating materials, these "shields" will block the leakage of the electric field, making the NCV unable to penetrate the detection.

Figure 9: NCV detection explanation.

5.1.10. Zero Fire Line Identification

Insert the watch pen into the hole of the outlet. For the fire line, the display will show a signal (e.g., 'EF') and emit a beeping sound. For the zero line, there will be no buzzer sound.

5.1.11. Data Hold and Flashlight

• نگهداری داده ها: Short press the 'HOLD' button to freeze the current reading on the screen. Press again to release.
• چراغ قوه: Long press the flashlight button to turn on the built-in flashlight for working in dim environments. Long press again to turn it off.

5.2. ANENG BT173 Battery Detector Operation

The BT173 is designed for simple, instant battery measurement without external power.

5.2.1. Testing 1.5V - 4.8V Batteries (AA, AAA, C, D, N, 10440, 14500, 16340, 18650, 21700, 26650, Button Cells)

Place the battery into the appropriate slot, ensuring the positive and negative terminals align with the contacts on the tester. The BT173 has multiple positive electrode contacts for different battery sizes (18650/21700/D, C/AA/14500, AAA/10440, N/16340, 1.55V button battery). The LCD screen will automatically display the voltage and battery level bar.

Figure 10: Battery level detection for D, C, AA, and AAA batteries.

Figure 11: Lithium battery detection for 21700, 14500, 10440, and 16340 types.

5.2.2. Testing 9V and 12V/23A Batteries

For 9V batteries, insert the battery into the dedicated 9V battery detection area at the bottom of the device. For 12V/23A batteries, use the dedicated 12V/23A battery detection port also at the bottom. Ensure correct polarity. The LCD screen will display the voltage و سطح باتری

Figure 12: Detection for 9V, 1.5V button, 12V, 18650, and 26650 batteries.

6. تعمیر و نگهداری

• تمیز کردن: برای تمیز کردن دستگاه از یک پارچه نرم و خشک استفاده کنید. از پاک کننده ها یا حلال های ساینده استفاده نکنید.
• ذخیره سازی: دستگاه‌ها را در جای خشک و خنک و دور از نور مستقیم خورشید و دمای شدید نگهداری کنید.
• Battery Replacement (ST184): Replace the AAA batteries in the ST184 when the low power prompt appears on the display.
• Automatic Shutdown (ST184): The ST184 clamp meter will automatically shut down after 15 minutes of no operation to save power.

7 عیب یابی

• ST184 does not power on: Check if the AAA batteries are correctly installed and have sufficient charge.
• BT173 LCD does not display: Ensure the battery is in firm contact with both terminals of the tester. If contact is good and still no display, the battery being tested may be completely discharged.
• قرائت‌های نادرست: Ensure test leads are properly connected and not damaged. Verify the correct measurement mode is selected (if not in auto-ranging). For current measurements, ensure only a single wire is clampویرایش
• NCV حجم را تشخیص نمی‌دهدtage: Ensure the sensor is within 2cm of the live source and not obstructed by thick insulation or metal shielding.

8. مشخصات

8.1. ANENG ST184 Smart AC Clamp متر

Note: The parameters are for reference only, and the actual measurement of the specific equipment shall prevail.

8.2. ANENG BT173 Battery Detector

Note: The parameters are for reference only, and the actual measurement of the specific equipment shall prevail.

9. نکات کاربر

• بازیافت باتری: The BT173 is ideal for quickly identifying truly dead batteries, helping you sort and recycle them efficiently.
• Single Wire Current Measurement: Remember that the ST184 clamp meter measures current by detecting the magnetic field around a single conductor. Do not clamp around an entire power cord (which contains both live and neutral wires) as this will result in a zero reading.
• Capacitor Safety: Always discharge capacitors before testing them with the ST184 to prevent damage to the meter and ensure personal safety.
• Auto-Ranging Convenience: Leverage the auto-ranging feature of the ST184 to simplify your measurements. The meter will automatically select the correct range for the parameter being measured.
• شرایط کم نور: Utilize the ST184's built-in flashlight and backlit display when working in poorly lit areas for improved visibility and safety.

10. گارانتی و پشتیبانی

The ANENG Pro Kit ST184+BT173 is CE certified, indicating compliance with European safety standards. For specific warranty details and technical support, please refer to the documentation provided with your purchase or contact the seller directly.