Sarrera
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ikea KALLROR 503.570.02 Stainless Steel Cabinet Handles. Please read these instructions carefully before proceeding with installation to ensure proper and safe use.
Produktua amaituview
The Ikea KALLROR 503.570.02 handles are designed to offer a modern aesthetic and functional grip for your kitchen cabinets or drawers. This set includes two handles and all necessary screws for a complete installation.
This image displays two sleek, cylindrical stainless steel cabinet handles, along with four silver screws. The handles have a brushed finish, and each handle is shown with two mounting posts. The screws are designed to secure the handles to cabinet doors or drawers.
Zehaztapenak
| Modelo zenbakia | 503.570.02 |
| Marka | Ikea |
| Multzo bakoitzeko kantitatea | 2 helduleku |
| Heldulekuaren luzera | 213 mm |
| Heldulekuaren Sakonera | 38 mm |
| Hole Spacing (center-to-center) | 160 mm |
| Zuloaren diametroa | 5 mm |
| Atearen lodiera egokia | 16 mm-tik 21 mm-ra |
| Handle/End Cap Material | Altzairu herdoilgaitza |
| Plastic Parts Material | Polietilenozko plastikoa |
| Dakarten osagaiak | Instalazio-hardwarea (torlojuak) |
| Pisua | 170 gramo |
Konfigurazioa eta Instalazioa
Installing your Ikea KALLROR cabinet handles is a straightforward process. Follow these steps carefully for a secure attachment.
Beharrezko tresnak
- Zulagailua
- Drill bit (5 mm diameter)
- Neurtzeko zinta edo erregela
- Arkatza
- Bihurkin (Phillips burukoa gomendatzen da)
Instalazio urratsak
- Neurtu eta markatu: Carefully measure and mark the desired position for the handle on your cabinet door or drawer front. Ensure the marks for the two screw holes are precisely 160 mm apart (center-to-center).
- Zulatzeko zuloak: Using a 5 mm drill bit, carefully drill through the cabinet door or drawer front at the marked positions. Ensure the holes are straight and clean.
- Erantsi heldulekua: Align the handle with the drilled holes. Insert the provided screws from the inside of the cabinet door or drawer through the drilled holes and into the handle posts.
- Helduleku segurua: Tighten the screws firmly with a screwdriver until the handle is securely attached. Ez estutu gehiegi, as this may damage the cabinet material.
- Errepikatu: Repeat the process for the second handle if installing a set.
Important: These handles are suitable for door thicknesses between 16 mm and 21 mm. Verify your cabinet door thickness before drilling.
Funtzionamendua
The Ikea KALLROR cabinet handles are designed for simple and reliable operation. Grasp the handle firmly to open or close cabinet doors and drawers as needed.
Mantentzea
To ensure the longevity and appearance of your stainless steel handles, follow these maintenance guidelines:
- Garbiketa: Garbitu aldizka zapi leun batekin,amp cloth. For stubborn marks, use a mild detergent solution. Avoid abrasive cleaners, scouring pads, or chemical solvents, as these can damage the stainless steel finish.
- Lehortzea: Always dry the handles thoroughly after cleaning to prevent water spots and maintain their luster.
- Ikuskapena: Periodically check the screws for tightness. If a handle feels loose, gently tighten the screws with a screwdriver.
Arazoak konpontzea
Handle is Loose
If the handle feels loose, gently tighten the screws from the inside of the cabinet door or drawer. Ensure not to overtighten.
Instalatzeko zailtasuna
Ensure the drilled holes are precisely 160 mm apart (center-to-center) and that the drill bit used was 5 mm in diameter. Verify your cabinet door thickness is within the specified 16-21 mm range.
Laguntza
For further assistance or inquiries regarding your Ikea KALLROR cabinet handles, please refer to the official Ikea webwebgunean edo jarri harremanetan Ikea bezeroarentzako arreta-zerbitzuarekin zuzenean.
