ETRONIX PULSE EX4S Digital System Instruction Manual
Thank you for purchasing this R/C System.
Before using, read this manual carefully.
Product Overview
CAUTION
To work your R/C with your model correctly and safely please ensure that you read this manual carefully and keep it safe for future reference.
Warning
- This product is only suitable for use with radio-controlled models.
- Only use this product within the approved relevant laws and regulations,
- Etronix are not responsible for misuse.
- Etronix will not be responsible for damage caused by unauthorised modification, adjustment o replacement of parts within this product.
- Due to ongoing R&D, some visual differences and set-up may differ so check the Etronix website if you require the latest version.
Before use ensure:
- The batteries have sufficient charge
- Keep the radio away from moisture, high temperature or heavy vibration.
- Do not clean the radio with solvent
- Ensure the antenna does not touch anything else when turning the unit on.
- Keep away from children
Function
Binding process
With 4 x AA batteries installed inside the transmitter (TR) hold the ‘ENT’ (Enter) button switch on. The four LED lights on the front panel will light solid red and you will hear a buzzing sound ‘B-B-B…’ It is now in the binding status. Next power on the model and receiver (RX). The RX LED green light will flash slowly. Now move the RX close to the TR and press the white bind button on the RX until the LED green light flashes quickly several times and then settles to a slow flash.
This now confirms that binding has been successful. Turn off the TR, the turn back on again. The RX LED green light will now be solid and the set-up complete.
Caution
Make sure the RX and TX are within one metre of one another.
Despite being within effective distance if you find the RX LED green light flashes for no reason then the RX may be starting anti-interference and automatically entering the S’F mode. If this happens, you only need to provide the RX a control signal, such as moving the TR throttle or ST steering sticks and the RX will be connected again.
Servo Direction
Press the “EXT” or “ENT” button for 2 seconds and the buzzer will sound “B”.
The servo direction for the throttle (TH) or steering (ST) has now been reversed.
Fail Safe Setup (F/S)
This function is to protect your model when the signal becomes weak or is lost. Failsafe will automatically put the throttle (TH) in a neutral position.
The F/S is set inside the receiver.
With electric powered models the F/S is set in the RX, no need to set.
For nitro powered models, pull the TH stick back to the brake position keeping the RX white F/S button pressed until the green flashing LED goes solid. Release the white button and the F/S function will be set successfully. If you have to re-bind the RX to the TX, then the nitro model F/S will need to be reset.
3rd and 4th Channel Option
These are ideal for using extra functions on your model such as a servo operated 2-speed transmission, winch or LED lighting. The 4th channel has a three-step toggle switch for potentially cycling through a plug in option feature.
Important Notice
Please do not forcefully move the sticks in the direction of the red indicators.
The radio is a converted flight radio and for the purpose of use with surface models only.
The sticks are fixed into the position and the internals can be damaged If the sticks are forced in the wrong direction, voiding any warranty.
Specifications:
Transmitter Specifications:
Item: ET1109 EX4S
channels: 4
Model Type: Car/Boat
RF range: 2.40-2.48GHz
RF power: less than 20dBm
2.4GHz System: FHSS
Code Type: 2-FSK
Sensitivity: 1024
Low voltage warning: less than 4.9V
(7.2V-7.5V for 2S Li-Po)
Response time: 3nm
Power: 4.9V-8.4V
Weight: 470g
Size: 80 x 185 x 222mm
Certificate: CE, UKCA
Receiver Specifications:
Item: ET1166 EX4S
Channels: 4
RF range: 2.4-2.48GHz
2.4GHz System: FHSS
Code Type: 2-FSK
Power: 4.6V-8.4V
Weight: 8g
Size: 13 x 20 x 30mm
Rx Sensitivity: –105dBm
Certificate: CE, UKCA
(Please ensure that the positive and negative poles of the battery are not connected inversion or the RX will short out.
Etronix is a division of CML Distribution Limited. Saxon House, Saxon Business Park, Hanbury Road, Bromsgrove.
Worcestershire. B60 4AD.
Email: sales@etronix-rc.com
Web: www.etronix-rc.com
Documents / Resources
 |
ETRONIX PULSE EX4S Digital System [pdf] Instruction Manual ET1109, PULSE EX4S Digital System, PULSE EX4S, PULSE, Digital System, System |