1. Toote lõppview
The BeA Digital Transmitter is a compact, single-button device operating at a frequency of 433 MHz. It is designed for various remote control applications requiring a reliable digital signal transmission.
Peamised omadused:
- Sagedus: 433 MHz
- Nupp: (1) Single button for operation
- Kompaktne disain: Kerge ja kaasaskantav
- Päritolu: Valmistatud Hiinas
Joonis 1: Esiosa view of the BeA Digital Transmitter. This image displays the compact black casing, the prominent single black button, and a small red LED indicator light located below the button. A metal key ring loop is visible at the top.
2. Seadistamine
The Digital Transmitter is designed for ease of use and typically requires minimal setup. Ensure the device has a working battery before operation.
2.1. Aku paigaldamine/kontrollimine
- Locate the battery compartment on the back or side of the transmitter. This may require a small screwdriver to open.
- Insert the required battery type (refer to the device's internal markings or packaging for specific battery type, typically a coin cell battery) ensuring correct polarity (+ and -).
- Sulgege patareipesa kindlalt.
- Test the transmitter by pressing the button; a small red indicator light should illuminate, confirming power.
2.2. Pairing (If Applicable)
This transmitter operates at 433 MHz. For integration with a receiver system, follow the pairing or learning instructions provided with your specific 433 MHz receiver unit. The transmitter sends a unique digital code when its button is pressed.
3. Kasutusjuhised
Using the Digital Transmitter is straightforward.
- Ensure the transmitter has a functional battery.
- Point the transmitter towards the intended receiver (if directional operation is required by your receiver system).
- Press and hold the single button firmly for approximately 1-2 seconds.
- Observe the red indicator light on the transmitter; it should illuminate while the button is pressed, indicating a signal is being transmitted.
- Release the button once the desired action is performed by the receiver.
The effective range of the transmitter will vary depending on environmental factors, receiver sensitivity, and obstructions. For optimal performance, maintain a clear line of sight if possible.
4. Hooldus
Proper maintenance ensures the longevity and reliable operation of your Digital Transmitter.
4.1. Aku vahetamine
When the red indicator light dims or fails to illuminate, or if the transmission range decreases significantly, it is likely time to replace the battery. Follow the battery installation steps outlined in Section 2.1.
4.2. Puhastamine
Clean the exterior of the transmitter with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water.
4.3. Ladustamine
Store the transmitter in a cool, dry place away from direct sunlight, extreme temperatures, and high humidity. If storing for extended periods, consider removing the battery to prevent leakage.
5. Veaotsing
If you experience issues with your Digital Transmitter, refer to the following common problems and solutions:
| Probleem | Võimalik põhjus | Lahendus |
|---|---|---|
| Transmitter not responding / Indicator light not illuminating. | Tühja või valesti paigaldatud aku. | Vaheta patarei välja, veendudes õiges polaarsuses. |
| Short transmission range or intermittent operation. | Low battery, interference, or obstructions. | Replace battery. Reduce distance to receiver. Remove obstructions. Check for strong interference sources (e.g., other 433 MHz devices). |
| Vastuvõtja ei reageeri saatjale. | Transmitter not paired with receiver, or receiver issue. | Ensure the transmitter is correctly paired with your receiver (refer to receiver's manual). Verify receiver is powered and functioning correctly. |
6. Tehnilised andmed
| Atribuut | Detail |
|---|---|
| Mudeli number | 10TD433HH1 |
| Kaubamärk | BeA |
| Sagedus | 433 MHz |
| Nuppude arv | 1 |
| Toote mõõtmed | 3.2 x 2.6 x 1.2 tolli |
| Kauba kaal | 0.01 untsi |
| ASIN | B00LU4I9NU |
| Tootja | BEA |
| Esmakordselt saadaval olev kuupäev | 28. september 2011 |
7. Garantii ja tugi
7.1. Garantii teave
Specific warranty details for the BeA Digital Transmitter are typically provided by the manufacturer at the time of purchase or can be found on the official BeA webPalun hoidke ostutõend alles garantiinõuete esitamiseks.
7.2. Tehniline tugi
For technical assistance, further troubleshooting, or inquiries regarding your BeA Digital Transmitter, please contact the manufacturer directly or refer to their official support channels. Contact information can usually be found on the manufacturer's websait või toote pakend.
Võite külastada BeA brand page on Amazon lisateabe saamiseks.
