Sissejuhatus
This manual provides essential instructions for the proper setup, operation, and maintenance of your Hatco 02-16-050 Horizontal Mechanical Drum Thermometer. Please read this manual thoroughly before installation and use to ensure safe and efficient performance. The Hatco 02-16-050 is a genuine Hatco OEM replacement part designed for accurate temperature measurement in compatible systems.
Figure 1: Hatco 02-16-050 Horizontal Mechanical Drum Thermometer. This image displays the Hatco 02-16-050 Horizontal Mechanical Drum Thermometer. It features a black rectangular body with an analog display window, from which white wires extend, terminating in a metallic probe tip. The device is designed for temperature measurement in specific applications.
Ohutusteave
- Always ensure the power supply to the equipment is disconnected before installing or servicing the thermometer.
- Handle the thermometer and its components with care to prevent damage.
- Only use this thermometer for its intended purpose as a replacement part for compatible Hatco equipment.
- Refer to the main equipment's service manual for specific installation procedures if this thermometer is part of a larger system.
Seadistamine ja installimine
The Hatco 02-16-050 thermometer is designed for integration into specific Hatco equipment. Installation should ideally be performed by a qualified technician.
- Ettevalmistus: Ensure the host equipment is powered off and disconnected from its power source. Allow any hot surfaces to cool down.
- Juurdepääs: Locate the existing thermometer or the designated installation point within the equipment. This may require removing access panels.
- Eemaldamine (asendamise korral): Carefully disconnect the wires from the old thermometer and remove it from its mounting. Note the orientation and wiring connections for correct reinstallation.
- Paigaldamine: Insert the new Hatco 02-16-050 thermometer into the designated mounting slot. Ensure it is securely seated.
- Juhtmed: Connect the white wires of the new thermometer to the appropriate terminals as per the host equipment's wiring diagram. Ensure connections are secure and properly insulated if necessary.
- Sondi paigutus: Position the metallic probe tip in the area where temperature measurement is required, ensuring good thermal contact.
- Kinnitamine: Once installed, replace any access panels. Before restoring power, double-check all connections.
Kasutusjuhised
The Hatco 02-16-050 is a mechanical thermometer with an analog display, providing a fast reading system for temperature monitoring.
- Toide sisse: Once installed and the host equipment is powered on, the thermometer will begin to register the temperature of its environment.
- Lugemistemperatuur: Observe the analog dial through the display window to read the current temperature. The "Fast Reading System" feature allows for quick temperature updates.
- Jälgimine: Continuously monitor the temperature as required by your application. No user adjustments are typically needed for this mechanical thermometer.
Hooldus
Termomeetri nõuetekohane hooldus tagab selle pikaealisuse ja täpsuse.
- Puhastamine: The thermometer's outer material is stainless steel. As per product care instructions, wipe clean välisilme koos kuulutusegaamp cloth. Do not immerse the thermometer in liquids. Ensure the host equipment is powered off and cooled before cleaning.
- Ülevaatus: Periodically inspect the thermometer for any signs of physical damage, loose connections, or corrosion.
- Kalibreerimine: Mechanical thermometers generally do not require user calibration. If you suspect inaccurate readings, consult a qualified service technician or refer to the host equipment's service manual.
Veaotsing
If you encounter issues with your Hatco 02-16-050 thermometer, consider the following:
| Probleem | Võimalik põhjus | Lahendus |
|---|---|---|
| No temperature reading / Stuck needle |
|
|
| Ebatäpne temperatuurinäit |
|
|
For issues not listed here or if troubleshooting steps do not resolve the problem, contact Hatco customer support or a qualified service technician.
Tehnilised andmed
| Mudeli nimi | 02-16-050 |
| Kaubamärk | Hatco |
| Kuva tüüp | Analoog |
| Erifunktsioon | Kiire lugemise süsteem |
| Reageerimisaeg | 500 millisekundit |
| Väline materjal | Roostevaba teras |
| Värv | Must |
| Toote mõõtmed | Ligikaudu 5 x 5 x 9 tolli (P x L x K) |
| Kauba kaal | 0.353 untsi |
| Korduvkasutatavus | Korduvkasutatav |
| Kasutamine siseruumides/välistingimustes | Siseruumides |
| Nõutavad patareid | Ei |
| UPC | 046843274376 |
Garantii teave
Specific warranty details for the Hatco 02-16-050 Horizontal Mechanical Drum Thermometer are not provided within this document. For information regarding warranty coverage, terms, and conditions, please refer to the official Hatco website or contact Hatco customer service directly. Keep your purchase receipt as proof of purchase.
Klienditugi
If you require further assistance, have questions about installation, operation, or need to report a problem, please contact Hatco customer support. Contact information can typically be found on the official Hatco websaidil või toote pakendil.
Hatco Official Websait: www.hatcocorp.com
