Hager ESC225S vaikse kontaktori kasutusjuhend

1. Sissejuhatus

This manual provides essential information for the safe and effective installation, operation, and maintenance of the Hager ESC225S Silent Contactor. Please read this manual thoroughly before attempting any installation or operation. Retain this document for future reference.

2. Toote lõppview

The Hager ESC225S is a silent contactor designed for switching electrical loads in various applications, particularly where quiet operation is desired. It features a 25 Amp current rating and two normally open (NO) contacts, operating at 230 Volts. Its compact design allows for integration into standard electrical panels.

Üksikasjalik view of the Hager ESC225S Silent Contactor, showing its terminals, model number, and electrical ratings. The device is white with blue accents, indicating the Hager brand and model ESC 225, with ratings of 25A and U:250V visible on the label. Connection terminals A1, A2, 1, 2, 3, and 4 are clearly marked.

3. Ohutusalane teave

• Elektrioht: Paigaldust ja hooldust tohivad teostada ainult kvalifitseeritud ja volitatud töötajad.
• Always disconnect power to the circuit before installing, servicing, or removing the contactor.
• Veenduge, et kogu juhtmestik vastab kohalikele ja riiklikele elektrieeskirjadele ja -määrustele.
• Do not operate the device if it appears damaged or has been exposed to moisture.
• Paigaldamise ja hoolduse ajal kasutage sobivaid isikukaitsevahendeid.

4. Paigaldamine ja seadistamine

The Hager ESC225S Silent Contactor is designed for DIN rail mounting within an electrical enclosure.

4.1 Paigaldamine

1. Ensure the electrical panel is de-energized.
2. Snap the contactor onto a standard 35mm DIN rail.
3. Ensure it is securely fastened and does not wobble.

4.2 Juhtmestik

Refer to the wiring diagram on the device and the following general guidelines:

• Juhtahel: Ühendage juhtvoldtage (230V AC) to terminals A1 and A2. A1 is typically the phase, and A2 is the neutral.
• Põhiahel: Connect the load circuit to the main power terminals. Terminals 1 and 3 are typically inputs, and terminals 2 and 4 are outputs for the two normally open (NO) contacts.
• Veenduge, et kõik ühendused oleksid tihedalt ja kindlalt kinnitatud, et vältida lahtisi kontakte ja ülekuumenemist.
• Use appropriate wire gauges for the 25 Amp praegune reiting.

5. Operatsioon

Once properly installed and wired, the Hager ESC225S Silent Contactor operates by receiving a control signal at its A1/A2 terminals. When the control voltage is applied, the internal coil is energized, closing the normally open contacts (1-2 and 3-4), thereby allowing power to flow to the connected load. When the control voltage is removed, the coil de-energizes, and the contacts open, interrupting the power to the load. The 'silent' characteristic refers to its low-noise switching operation.

6. Hooldus

The Hager ESC225S Silent Contactor is designed for long-term, reliable operation with minimal maintenance. However, periodic inspection is recommended:

• Visuaalne kontroll: Annually inspect the contactor for any signs of physical damage, discoloration, or loose connections.
• Puhastamine: Ensure the device is free from dust and debris. Use a dry, soft cloth for cleaning. Do not use liquid cleaners.
• Ühenduse kontroll: Periodically verify that all terminal screws are tight.

Enne hooldustööde tegemist ühendage alati toide lahti.

7. Veaotsing

If the contactor is not functioning as expected, consider the following:

For issues not resolved by these steps, contact a qualified electrician or Hager technical support.

8. Tehnilised andmed

9. Garantii ja tugi

For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your authorized Hager distributor. Technical support and further assistance can be obtained through the official Hager website or your local service representative.

Hageri ametnik Websait: www.hager.com