6B02 Series Shift Keyboard Case
Specifications
- Power: 1-3W
- Charging Indicator: Yes
- Backlight Brightness Levels: Off, Low, Medium, High
- Trackpad Control: Yes
- Shortcut Keys: Home, Brightness +/-, Multitasking view, Search, Dictation, Screenshot, Previous song, Play/Pause, Next song, Mute, Volume+/-, Lock screen
Product Usage Instructions
- Power Switch
- Toggle the side power switch to turn the keyboard on/off.
- Pairing Mode Auto Reconnect
- Press + for 3 seconds to enter pairing mode. The Bluetooth indicator will flash blue. If not connected within 5 minutes, the pairing mode will turn off. When turned on for 5 seconds, the keyboard will automatically attempt to reconnect with the last paired device.
Power Light Overview
Charging: Fully charged: Low battery:
- Standby Mode
- After 30 seconds of inactivity, the keyboard backlight will turn off automatically. If the keyboard remains unused for 30 minutes, it will enter standby mode. Press any key to wake up the keyboard.
- Backlight Settings
- Press + cmd to adjust the backlight brightness and cycle through the levels: Off, Low, Medium (default), High.
- Trackpad Control
- Press + to enable or disable the trackpad.
- Factory Reset
- Press and hold + + for 3 seconds. All indicators will flash to indicate that the factory reset is complete.
- Shortcut Keys
- Refer to the manual for various shortcut functionalities.
Troubleshooting Guide
If the keyboard stops working, follow these steps:
- Ensure the keyboard power is turned on.
- If the keyboard is out of battery (below 20%), charge it using the original charging cable.
- If the connection is unstable, restart the keyboard. If the problem persists, disconnect the keyboard from your device list and follow the pairing instructions to reconnect your keyboard.
Scan to watch a quick setup vide
esrtech.com/faq/shift-keyboard
- Power/Bluetooth indicator
- Caps lock indicator
- Charging indicator
- Power switch
The power delivered by the charger must be between a minimum 1W required by the radio equipment, and a maximum 3W in order to achieve the maximum charging speed.
User Manual
- Power Switch Toggle the side power switch to turn the keyboard on/off.
- Pairing Mode
Press
+ 
for 3 seconds to enter pairing mode. The Bluetooth indicator will flash blue. If not connected within 5 minutes, the pairing mode will turn off. - Auto Reconnect
When turned on for 5 seconds, the keyboard will automatically attempt to reconnect with the last paired device. - Power Light Overview
Charging:
Fully charged:
Low battery:
- Standby Mode
After 30 seconds of inactivity, the keyboard backlight will turn off automatically. If the keyboard remains unused for 30 minutes, it will enter standby mode. Press any key to wake up the keyboard. - Backlight Settings
Press+
to adjust the backlight brightness and cycle through the levels: Off, Low, Medium (default), High. - Trackpad Control
Press+to enable or disable the trackpad. - Factory Reset
Press and hold + 
+
for 3 seconds.
All indicators will flash to indicate that the factory reset is complete.
Shortcut Keys +
Troubleshooting Guide
If the keyboard stops working, please check the following:
- Ensure the keyboard power is turned on.
- If the keyboard is out of battery (below 20%), charge the keyboard using the original charging cable.
- If the connection is unstable, restart the keyboard. If the problem persists, disconnect the keyboard by going to your iPad’s Settings and removing “ESR Shift Keyboard” from the device list. Follow the pairing instructions to reconnect your keyboard.
If the keyboard remains unresponsive, repeat the steps above. If you are still experiencing problems, contact our customer service for further assistance.
Reminder
- This keyboard has a built-in polymer rechargeable battery that lasts for weeks of normal use. The battery has no memory effect and can be charged at any time.
- When not using the keyboard for an extended time, turn it off to prevent power drain and prolong battery life.
FCC STATEMENT
FCC ID:2APEW-6B026
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.·
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
IC:24790-6B026
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard( s). Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.”
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
This product is intended for use within Europe. Electronic Silk Road Corp. hereby declares that this product 6B026/6B027/6B028 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU,2014/30/EU. The Declaration of Conformity for the 6B026/6B027/6B028 is available from www.esrtech.com
This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
FAQ
- Q: How do I adjust the backlight brightness?
- A: Press + cmd to cycle through Off, Low, Medium, and High brightness levels.
- Q: How can I enable or disable the trackpad?
- A: Press + to enable or disable the trackpad functionality.
- Q: What should I do if my keyboard stops working?
- A: Follow the troubleshooting guide provided in the manual. Ensure the power is on, charge if needed, and reconnect following the pairing instructions if needed.
Documents / Resources
 |
ESR 6B02 Series Shift Keyboard Case [pdf] User Manual 6B026, 6B027, 6B028, 6B02 Series Shift Keyboard Case, 6B02 Series, Shift Keyboard Case, Keyboard Case, Case |