Contents
hide
ESL VISION ESL-ISS-MSEN-01 IntelliSense Panel Sensors
Product Specifications:
- Output Voltage: 10 VDC
- Output Current: 10mA Max
- Output Power: 0.1W
- Compliance: UL8750
- Warranty: 5 Years
Installation Instructions:
- Remove the sensor plate from the fixture’s rim.
- Remove the flat cable from the back of the plate.
- Insert the cable terminals into the approved sensor.
- Snap the sensor into the fixture securely.
Remote Programming Instructions:
Memory Mode (Commissioning):
Set settings to a program profile A to F and send settings to sensor.
Continuous Adjustment or Daylight Harvesting Mode:
- Trim-High=100%, Sensitivity=low, T1=30min, Standby Dim=50%, T2=15min, Photocell=CAL
- Trim-High=100%, Sensitivity=low, T1=30min, Standby Dim=50%, T2=15min, Photocell=OFF
- Trim-Low=50%, Sensitivity=low, T1=30min, Standby Dim=50%, T2=30min, Photocell=CAL
- Manual Mode, Trim-High=100%
- Daylight Harvesting, Trim-Low=50%, Sensitivity=low, T1=15min
FAQ
- Q: How do I reset the sensor to default settings?
- A: To reset to default settings, follow the RESET MODE instructions provided in the manual.
- Q: What is the standby time for the sensor?
- A: The sensor has a standby time of 5 minutes with no motion, and the fixture dims to 30%. After 60 minutes with no motion, the fixture turns off.
Project:
Catalog #:
Notes:
Date:
Overview
The ESL Vision ESL-ISS-SSEN-01 is a standalone PIR occupancy and daylight harvesting sensor designed for quick installation into our IntelliSense™ quick connect lighting fixtures. With this sensor installed, the fixture becomes remote programmable, allowing for single fixture control.
Key Features & Benefits
- PIR Occupancy Sensing
- Daylight Harvesting
- High & Low Trim Capable
- Single Fixture Control
- Simple Remote Programming
- Simple Lighting Control
Product Specifications
INPUT
- Input Voltage: 12 VDC
- Input Current: 9mA Max
- Input Power: 0.1W
- Dimming: Class 2, 0–10 VDC, 10mA Max
- Sinking Current: 10mA Max
OUTPUT
- Output Voltage: 10 VDC
- Output Current: 10mA Max
- Output Power: 0.1W
ENVIRONMENT
- Housing Material: UL 94-5VA Plastic
- Location of Use: Indoor
- Detection Range: 32 Feet Max
- Mounting Height: 15 Feet Max
- Operating Temperature: -22°F to 149°F (-30°C to 65°C)
- Storage Temperature: -22°F to 185°F (-30°C to 85°C)
- IP Rating: IP20
CERTIFICATIONS
- Compliance: UL8750
- Warranty: 5 Years
Ordering Guide
Catalog Data
| ITEM # | DESCRIPTION |
| ESL-ISS-MSEN-01 | MultiSense™ – Plug and Play 3 Wire networked PIR occupancy and daylight harvesting sensor |
| ESL-ISS-SSEN-01 | SoloSense™ – Plug and Play 3 Wire PIR occupancy and daylight harvesting sensor |
Installation
- Remove the sensor plate from fixtures rim.
- Remove the flat cable from the back of the plate.
- Insert the cable terminals into the approved sensor.
- Snap the sensor into the fixture securely.
Coverage
Wiring Diagram
Dimensions
- IntelliSense™ Panel Sensors
- ESL-ISS-MSEN-01 & ESL-ISS-SSEN-01
Remote Programming Instructions
Remote Programming Instructions: Memory Mode (Commissioning)
- Select either A, B, C, or D.
- Indicator lights on the remote will flash to indicate the current saved settings.
- Settings can be configured by pressing appropriate buttons in the highlighted gray section of the remote buttons. (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review selected settings and make changes as necessary.
- Point IR remote to desired luminaire for configuration and press “SEND”.
- If the configuration is successful, luminaire will flash twice to confirm settings are saved. Any parameter change to the current saved settings on A to F will override previous settings and will be automatically saved on the remote. If configuring multiple luminaires, select the configured memory mode A to E then follow steps 4 and 5.
E Mode allows visual adjustment to choose the desired dimming level.
Remote Programming Instructions: Continuous Adjustment or Daylight Harvesting Mode
- Point IR remote to desired luminaire.
- Press “ON” then press DIM+ or DIM- to adjust dimming level.
- Press “F”, indicator lights on the remote will indicate current saved settings.
Note: only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings. - Review selected settings and make changes as necessary. Press “SEND”.
- If the configuration is successful, luminaire will flash twice to confirm setting saved. If configuring multiple luminaires, select the configured DAYLIGHT HARVESTING settings then follow steps 4 and 5.
RESET MODE
- Motion: 100%
- No Motion: 5 minutes and fixture dims to 30%
- No Motion: 60 minutes and fixture turns off
Contact
†Not All Part Numbers DLC Qualified. For a Complete Listing Please Consult the DLC Qualified Products List (QPL).
- 888.493.5559
- info@esivision.com
- www.esivision.com
Documents / Resources
 |
ESL VISION ESL-ISS-MSEN-01 IntelliSense Panel Sensors [pdf] Owner's Manual ESL-ISS-MSEN-01, ESL-ISS-SSEN-01, ESL-ISS-MSEN-01 IntelliSense Panel Sensors, ESL-ISS-MSEN-01, IntelliSense Panel Sensors, Panel Sensors, Sensors |
 |
ESL VISION ESL-ISS-MSEN-01 IntelliSense Panel Sensors [pdf] Owner's Manual ESL-ISS-MSEN-01, ESL-ISS-MSEN-01 IntelliSense Panel Sensors, IntelliSense Panel Sensors, Panel Sensors, Sensors |
