XTOOL S1 Laser Cutter Safety Instructions

General Safety

Read and get familiar with all safety precautions and procedures before using the machine. Strictly follow all safety precautions. Ensure that the machine is properly assembled and is working properly.

Operating Principles:

• ⚠️ Check the machine for damage every time before you use it. Do not operate it in any way when any damage or defect is found.
• Ensure that the workspace is clean and flat.
• Do not disassemble the machine or change its structure in any way without authorization. Do not modify or decompile its operating system.
• Do not leave the device unattended during operation. Pay attention to whether it is working properly.
• Keep the inside of the machine clean. Residues and chippings accumulated during cutting and engraving are dangerous and may cause a fire. Clean the chippings and residues inside the work area regularly.
• The machine works properly at the temperature of 0°C to +35°C and can be stored properly at the temperature of -10°C to +40°C. Do not operate it at a temperature lower than 0°C.
• Do not place or use your machine under direct sunlight.
• This product is not user-serviceable. It must be returned to the factory or repaired by authorized professionals.

Laser Safety

Generally, the laser module is completely enclosed in the casing and light shield during operation. The device has a safety interlock switch. If the lid is lifted during operation, the device will stop working.

Safety Precautions:

• ⚠️ Do not operate the machine when any part of it is removed. Removing any part may expose the laser system and cause damage to the machine.
• Do not engrave or cut any material that contains PVC or vinyl (processing plastics is not recommended). These materials (and other materials containing chlorine/chloride) can generate corrosive vapor that is extremely harmful to the human body and can cause damage to the device. Any damage caused by engraving or cutting any material containing PVC or vinyl is not covered by the Company's warranty.
• Do not engrave or cut any unknown materials. Vaporization or melting of many materials, which include but are not limited to PVC and polycarbonate, may release harmful smoke.
• Laser operation is prohibited when the lid is lifted. Make sure that the lid is closed during operation and do not tamper with the safety mechanism of the lid.
• Do not leave the device unattended during operation. Pay attention to whether it is working properly.

The reference standards for laser safety are the American National Standard for Safe Use of Lasers (Z136.1-2022), International Electrotechnical Commission Standard (IEC 60825-1:2014), and European Standards (EN 60825-1:2014/A11:2021).

Fire Safety

A high-density laser beam is used by the device to irradiate the material to be cut or engraved, so as to heat up the material surface and vaporize the material without burning. But most materials are inherently flammable and may be ignited to form an open flame that can burn down the device (even if it is made of flame-retardant materials) and its surroundings. Experience shows that vector cutting with a laser is most likely to produce an open flame. In particular, acrylic has proven to be extremely flammable in vector cutting.

? Do not leave the device unattended when it is working.

? Keep combustible materials away from the device.

Warnings and Suggestions:

• Equipment for use in locations where children are not likely to be present.
• Ensure that the workspace is well-ventilated so that the generated smoke can be discharged in time.
• Do not stack materials (especially organic ones, such as paper) around the machine. They may cause the spread of flames and increase the risk of material ignition.
• Do not leave the machine unattended when it is working. If the machine works with setting errors and is left unattended for a long period of time, or if a mechanical or electrical fault occurs, a fire may be caused.
• Clean the device regularly. Excessive accumulation of residues and chippings from cutting and engraving would increase the risk of fire. The internal working area needs to be cleaned periodically to ensure that there is no residue or chipping inside the device.
• Ensure that the area around the machine is clean without any cluttered flammable materials, explosives, or volatile solvents, such as acetone, alcohol, or gasoline.
• Keep a fire extinguisher and perform regular maintenance and inspection of it.
• If a fire occurs during processing, take good care of yourself. For a small flame, you can wait for it to go off; for a larger fire, please keep a safe distance and use a fire extinguisher to put it out.

Electrical Safety

⚠️ Read the following warnings and suggestions carefully:

• Do not open any access panel on the device when the device is connected to the power supply. Accidental contact with the power supply may cause injury.
• Do not touch any electronic area with your hands or other tools when the machine is connected to a power supply.
• The power switch is on the back of the device. Press (-) to power it on and press (o) to power it off.

Use and Maintenance

⚠️ Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Cut off the power before maintaining the device.

Warning and Instruction Signs

On xTool S1, the warning and instruction signs are labeled where physical injuries or damage to the machine may be caused before and/or during operation. If a sign is damaged or lost, replace it immediately. You can use the following template to print the sign you need.

DANGER - CLASS 4 LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED

AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION

CLASS 1 LASER PRODUCT CONSUMER LASER PRODUCT

Classification to IEC 60825-1: 2014 & EN 50689:2021

This machine shall be reclassified as Class 4 laser product if a riser base with passthrough is installed. Refer to the user manual for safety instruction details. Such combination of machine and riser base are intended for professional use only and are not intended for consumer use.

Laser Specifications

(Specifications may vary depending on the machine model)

After-sales Services

For technical support, contact us at support@xtool.com.

For more information about after-sales services, visit support.xtool.com.