ernitec 0070-24224-AC HDMI VGA BNC Monitor
Specifications:
- Model: 0070-24224-AC
- Product: HDMI/VGA/BNC Monitor
Product Information:
This HDMI/VGA/BNC Monitor offers multiple connection options and a range of menu settings for optimal viewing experience. The monitor comes with a remote control for easy operation and adjustment.
Product Usage Instructions
Controls:
The monitor features various controls for adjusting settings such as contrast, brightness, color, tint, sharpness, and more. Use the remote control or the buttons on the monitor to navigate through the menu options.
Accessories:
Ensure all accessories provided with the monitor are included in the package. This may include cables, a remote control, batteries, and a user manual.
Connection Options:
The monitor supports HDMI, VGA, and BNC connections for compatibility with different devices. Ensure to use the appropriate cable for your device and connect securely for optimal performance.
Basic OSD Setup:
Access the On-Screen Display (OSD) menu to set up basic settings such as language, duration, color range, screen adjustments, and more. Use the remote control to navigate through the OSD options and make adjustments as needed.
Troubleshooting:
If you encounter any issues with the monitor’s performance,refer to the troubleshooting section in the user manual. Follow the provided steps to identify and resolve common problems.
Maintenance:
Regular maintenance of the monitor is essential for optimal performance. Follow the maintenance guidelines outlined in the user manual to keep your monitor in good condition.
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). NO UESR SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,within an equilateral triangle,is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to rersons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions accompanying the appliance.
REGULATORY INFORMATION
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or experienced radio/monitor technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without written authorization from CVT electronics group. Unauthorized modification could void the user’ s authority to operate this product.
Safety instructions
WARNING:
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or splashing area.
An objects filled with liquids such as vases shall not be placed on the apparatus.
IMPORTANT SAFETY INSTRUCTIONS
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sourcesuch as radiators,heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Unplug this apparatus during lightning storms or when unused for long period of time.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use the attachments/accessories specified by the manufacturer.
- Refer all servicing to qualified service personnel.Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Use only with a cart, stand,tripod,bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, be cautious when moving the cartlapparatus combination to avoid injury from tip-over.
- Do not defeat the safety purpose of the polarized or grounding type plug.A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety.
When the provided plug does not fit for your outlet, consult an electrician for replacement of the obsolete outlet.
Note
- If the CCTV monitor feel cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with CCTV monitor.
- Some minute dot defects may be visible on the screen, appearing as tiny red,green, or blue spots. However there have no adverse effect on the monitor’s performance.
- Avoid touching the LED screen or holding your fingers)against it for long periods of time. In that case, it may produce some temporary distortion effect on the screen.
CAUTION connecting the Power Cord
Most appliances are suggested to be placed upon a dedicated circuit; that is a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits.
Do not overload wall outlets!Overloaded wall outets, loose or damaged wall outlets,extension cords, frayed power cords, damaged or craded wire insulation are dangerous. Any of these conditions could result in electric shock or fire.Periodically examine the cord of your appliance, and its if appearance indicates damage or deterioration, unplug it,discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse,such as being wisted, kinked, pinched, closed in a door,or walded upon.Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
On Disposal
- The fluorescent lamp used in this product contain a small amount of mercury.
- Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of your local authority.
NOTE: Picture of the instruction is not fotally with product you purchased, real product is referred as standard.
Introduction
Controls
This is a simplified representations of front panel.
- Here show may be some what different from your monitor.
Accessories
Ensure that the following accessories are included with your CCTV monitor. If any accessory is missing, please contact the dealer from where you purchased the product.
Connection Options
Remote Control Key Functions
Installing Batteries
Open the battery compartment cover on the the back side.
Insert ONE CR2032 3v batteries in correct polarity .DO not mix old or used batteries with new ones.
Close the cover.
Point the remote towards the remote control sensor of the wireless monitor and use it within 7 meters.
Put the used batteries into the recycling bin since it can negatively affect the environment.
External Equipment Connections
Power Cord Connection
Connect the power cord correctly as shown.
Press the POWER switch of your CCTV monitor to switch on the CCTV monitor.
The power indication on the front panel lights is green.
BNC INPUT and BNC OUTPUT Connection
- Connect the BNC in cable output of the PROCESSOR to the BNC input on the set.
- Connect the BNC out cable input of the other monitor to the BNC output on the set.
- Select BNCI or BNC2 input source with using the INPUT button on the remote control.
PC Connection
This CCTV monitor provides plug and play capability,meaning that the PC adjusts automatically to the monitor’ s setting. The CCTV monitor sends configuration information(EDlD) to the PC using the Video Electronics Standard Association (VESA)Display Data Channel(DDC) protocol.
- Connect the RGB output of the PC to the VGA in jack on the set.
- Turn on the PC and set.
- Select the VGA input source with using INPUT button on the remote control.
Basic OSD setup
Turning on and off the CCTV monitor
- Turn on monitor
- Connect the AC input cable to monitor, then press the main power switch on monitor. At this time the monitor will enter into standby mode and the indicator light turn red.
- Using buttons can turn on monitor from standby mode as follows:
Press POWER keyon front panel or on the remote control.
- Turn off monitor
- Press POWER button on front panel the or on the remote control to enter standby mode. The indicator light is red.
- Using main power switch turns off monitor completely.
Selecting screen language
NOTE:If you use your monitor for the first time,you should select the language which will be used for displaying menus and indications.
- Press the “MENU” button into main menu.
- Press the “
” button to select OSD menu. - Press the “
” button to select OSD LANGUAGE. - Press the “” button to select your language.
- When you are satisfied with your choice, press MENU to exit.
NO SIGNAL
There is NO SYNC menu on screen when there is no input signal.
Selecting input source
You can select the input source by pressing INPUT button on the remote control on the front panel.
- Press the “” button to select the source you want.
- Press the “INPUT” button to confirm.
OSD setup under VGA/HDMI input mode.
- Press the “MENU” button to access Main Menu setting interface.
- Press the ““to select the desired submenu.
- Press the ” “again to enter the submenu.
“Color Temp” Menu Option
- Press ““button to select PICTURE menu.
- Use “” to select what you want to adjust on Color Temp
- Press ““button to adjust “Medium” “Warm” “Cold” “User”
- When you are satisfied with your adjustment, press MENU to exit the main menu.
“Aspect Ratio” Menu Option
- Press ““button to select PICTURE menu.
- Use ” ” to select what you want to adjust on Color Temp
- Press ““button to adjust “Point to Point” “Zom1” “Zom2” “Auto ” “4:3”, “Panorama”
- When you are satisfied with your adjustment, press MENU to exit the main menu.
- Press “ “button to select PICTURE menu.
- Use “” to select what you want to adjust on Picture Mode
- Press ““button to adjust “Point to Point” “Zom1” “Zom2” “Auto ” “4:3”, “Panorama”
- When you are satisfied with your adjustment, press MENU to exit the main menu.
“Sound” Menu Option
- Press “”button to select Sound menu.
- Use “ ” to select what you want to adjust on Mode
- Press button to adjust “Balance” “Sound Mode” “Auto Volume” “ ”
- When you are satisfied with your adjustment, press MENU to exit the main menu.
“OPTION” and “FUNCTION”Menu Option
- Press “”button to select OPTION or FUNCTION menu.
- Use “” to select what you want to adjust on Mode
- Press “”button to adjust “OSD Language” “OSD Reset” “Software Update” etc
- When you are satisfied with your adjustment, press MENU to exit the main menu.
PRODUCT CRITERIA
Trouble shooting
Before connect the service technology, perform the following simple checks.
If any problem still exist,unplug the CCTV monitor and calling for serving.
TROUBLE SHOOTING
NOTE:There is a problem in VGA mode. (Only VGA mode applied)
Maintenance
Early manifuctions can be prevented. Careful and regular cleaning can extend the amount of time in that way,you will have a new one. Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the screen
Here’s a great way to keep the dust off screen for a while. Wet soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then used it to wipe the screen.
Make sure the remained water is off the screen, and then let it air-dry before you turn on your monitor.
Cleaning the cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth.
Extended Absence
If you expect to leave your monitor dormant for a long time(such as a vacation),it’s a good idea to unplug the power cord to it from lightning or power surges.
FAQ
Q: How do I adjust the sound settings on the monitor?
A: To adjust sound settings, navigate to the Sound menu using the remote control. Use the arrow keys to select the setting you want to adjust, then use the volume buttons to make changes. Press MENU to save your adjustments and exit.
Q: What should I do if the monitor does not display properly?
A: If you experience display issues, check the connection cables and ensure they are properly connected. You can also adjust the screen settings in the OSD menu to optimize the display.
Documents / Resources
 |
ernitec 0070-24224-AC HDMI VGA BNC Monitor [pdf] User Manual 0070-24224-AC, 0070-24224-AC HDMI VGA BNC Monitor, HDMI VGA BNC Monitor, VGA BNC Monitor, BNC Monitor, Monitor |