EPLO E18PRO, E13PRO Remote Control User Guide

EPLO E18PRO, E13PRO Remote Control User Guide

Installation Preparation

Remote control installation

Remote control holder installation 1：

1. Drill a 6 mm diameter hole in the wall to a depth of about 35 mm.
2. Remove the double-sided adhesive tape on the back of the holder.
3. Install an anchor into the hole, stick the holder to the wall and secure with screws and then stick the patch with tape.
   

Remote control holder installation 2：

1. Clean and dry the pre-installation area of the holder.
2. Remove the double-sided adhesive tape on the back of the holder.
3. Stick the holder to the wall vertically and then stick the patch with tape.
   

Battery installation: 

1. Insert batteries into the remote control.
2. Put the remote control to the holder.
   

Notice

1. Please ensure the remote control is within reach when a person on the seat.
2. Do not install and use the product in damp places such as a shower room.
3. Do not place the product in a place where it is easily exposed to water.

Installation Preparation

Remote control illustration

Usage Instruction

Notice :

• Only when the user is seated and the buzzer beeps can the functions of front/rear washingand drying be activated.
• Please sit backward on the seat for correct washing position and to avoid splashing.
• The nozzle will continue to spray for 1-2 seconds after user stands up during washing, so please press “STOP” button before standing

REAR|MOVE
Press ” ” button, the indicator light is on showing current water temperature level, it starts rear washing; Press again ” ” button to shift to oscillating washing (nozzle moves forward and backward to expand washing area). The washing will stop automatically after one cycle, while it will stop immediately if the user presses ” ” button

FRONT|MOVE
Press ” ” button, the indicator light is on showing current water temperature level, it starts front washing; Press again ” ” button to shift to oscillating washing (nozzle moves forward and backward to expand washing area). The washing will stop automatically after one cycle, while it will stop immediately if the user presses ” ” button  .

Pulse cleaning function (Only for the product with pulse cleaning function.)

During front/rear washing, long press ”  ” or ” ” button to turn on/off pulse cleaning mode.

Usage Instruction

DRY|DRYER TEMP (Only for the product with drying function)

① Press ” ” button, the indicator is on, showing the current air temperature level. It will stop drying automatically after one cycle or after leaving.
② Under drying, press ” ” button to adjust the air temperature between 0-5 level, and the indicator light is on showing the air temperature level. When the indicator light is off, the temperature = is at level 0 (room temperature).

Room temperature

Level 1

Level 2

Level 3

Level 4

Level 5

Water volume adjustment

Press “+” or ” – ” button when it is under function of rear washing or front washing, the indicator
light is on showing

Nozzle position adjustment

Press “∧” or “∨” button when it is under function of rear washing or front washing, the indicator light is on showing current nozzle position, and nozzle position can

Energy saving

Long press ” ” button to enter energy saving mode, long press ” ” button again to exit energy saving mode

Under energy saving mode, seat temperature is set to Level 1 for energy saving.
(Note: If the seat temperature before energy saving is neutral, then it will be neutral as well.)

Remark:
Energy saving mode will be suspended and the product will enter functional mode if the seat is used. The seat starts to heat immediately (without turning off the seat temperature), and the energy saving mode is restored once the seat is no longer being used.

Water temperature adjustment

Short press ” ” button to adjust the water temperature between 0-5 level. The indicator light is on showing current water temperature level. When the indicator is off, the temperature is at level 0 (room temperature).

Room temperature

Level 1

Level 2

Level 3

Level 4

Level 5

Seat temperature adjustment

Short press ” ” button to adjust the seat temperature between 0-5 level. The indicator light is on showing current seat temperature level. When the indicator is off, the temperature is at level 0 (room temperature).

Room temperature

Level 1

Level 2

Level 3

Level 4

Level 5

Night light

Night light adjustment：Short press ” ” button to turn on/turn off night light. · Intelligent mode: Long press ” ” button to enter into intelligent mode (Night light will be on or off depending on the surrounding light.). If the product is on intelligent mode, short press ” ”  button to exit intelligent mode. (Factory setting: intelligent mode)

Half flush/Full flush

Short press ” ” button, the toilet starts half flushing.
Short press ” ” button, the toilet starts full flushing.
ong press ” ” button to turn on/off auto flush function.

When the auto flush function is turned on, toilet will automatically flush after detecting user leaving the seat.

Auto lid open/close

Short press ” ” button，open or close the lid.
Short press ” ” button，open or close the seat.
Long press ” ”  button to turn on/off auto lid open/close function.

Auto deodorization

Short press ” ” button to turn on/off auto deodorization function. The deodorization function will be automatically turned on when the user is seated, and will stop after leaving. Under drying, deodorization will stop. (This function is turned on by default.)

Water tank flush volume adjustment
(Only for toilets with water tank flush volume adjustment function)

• Press and hold ” ” button, and press the water volume ” + ” button to increase full flush volume by 1 level.
• Press and hold ” ”  button, and press the water volume ” – ” button to reduce full flush volume by 1 level.
• Press and hold ” ” button, and press the water volume ” + ” button to increase half flush volume by 1 level.
• Press and hold ” ” button, and press the water volume ” – ” button to reduce half flush  volume by 1 level.

User code

Radio frequency remote control

① Shut off the power supply of toilet
② Press and hold ”   ” button, then press ” ” button, the indicator light will flash.
③ Re-connect the power plug and press “reset” button.
④ The indicator stops flashing and stays on for 2 seconds, indicating that the remote control and
the toilet are matched successfully. It beeps once when the self-inspection completes. Then the remote control is ready for use.

IR remote control

① Power on the toilet and the self-inspection starts. It beeps once when the self-inspection completes.
② Press and hold ” ” button, then press ” ” button, the indicator light will flash.
③ Press the Pressure ” + ” or ” – ” button to select user 1-9 (as shown below). The indicator light displays the corresponding user code and flashes.
④ Press ” ” button, then press ” ” button. The main unit beeps once, indicating that the remote control and the toilet are matched successfully.

User 1

User 2

User 3

User 4

User 5

User 6

User 7

User 8

User 9

Other operations

Quiet mode

• Press and hold the ” ” button and press the ” ” button to turn on/off quiet mode

Sterilization function

• When no one seated and washing/drying is off, long press ” ” button to turn on plasma sterilization function.This function will stop automatically after 2 hours. Under this mode, if any other button is pressed or user is seated, it will stop automatically. (Only for the toilet withsterilization function.)

Automatic pre-wetting function

• Press and hold ” ” button and press ” ” button to turn on or off automatic pre-wetting function. After the automatic pre-wetting function is turned on, the pre-wetting function will be performed when the user is detected to be seated. (Only for the toilet with automatic pre-wetting function.)

Foot sensor function

• Long press ” ” button to turn on/off foot sensor function. Foot sensor is deactivated when the user

Foot sensor indicator

• Press and hold ” ” button, and press ” ” button to turn on/off foot sensor indicator. (Only for the t

APP code matching

• Press and hold ”   ” and ” ” button simultaneously for longer than 3 seconds to start APP  code matching. (Only for the

Voice function

• · Press and hold the ” ” button and ” ” button at the same time for more than 3 seconds to  turn on or off the voice function. (This combination button is only available for toilets with voice function）

Electronic bidet tank flushing

• Press and hold ” ” and ” ” button simultaneously for longer than 3 seconds to start the flushing by water tank of electronic bidet. (Only for the toilet with electronic bidet tank flushing function.

Remark:

• The buzzer will “BEEP” once when the user presses one button indicating that the main unit receives the signal and conduct the operation accordingly. If the buzzer doesn’t sound, it means the main unit doesn’t receive the signal, please adjust the remote control direction and repressthe button.
• In case of power cut during nozzle spraying, the wand cannot be retracted, please wait until the power is restored. In case of a power cut for a long period, please push the wand softly back by hand. Do not p

The picture of product may not entirely consistent with actual appearance and color because of product improvements, please in kind prevail.

Thank you for choosing our product. Please read the instructions carefully before installation and keep it available for future maintenance or reference.
E-mail:service@eplo.com