Document

EnOcean-logo

EnOcean SIN-2-FP-01 Pilot Wire Heating Module

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-product

SPECIFICATION

  • Reference: SIN-2-FP-01
  • Power supply: 230V AC ~ 50Hz
  • Consumption: <1W
  • Heater maximum power: 3680 W
  • Metering of Instant power (W) and cumulated
  • Energy (Wh) – compatible home automation gateway needed (see the “Support” section on nodon.fr)
  • Radio frequency range: 868.0 to 868.6 Mhz
  • RF power max: +10dBm
  • Range: up to 30m indoor
  • Operational temperature: -10°C to 40°C
  • Protection rating: IP 30
  • Pairing: up to 22 controllers EEP (EnOcean Profile): D2-01-0C
  • Dimensions: 41 mm (l) x 44 mm (L) x 16.9 mm (h)
  • Weight: 29 g
  • Warranty: 2 years

USE CAUTIONS

  • Never use the device if it is not correctly installed and placed inside a connecting box in conformity with the current norms.
  • Keep the product far away from liquids.

DETAILED USER GUIDE

Directly access the detailed user guide on the Support section on nodon.fr/en/technicalsupport/

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-1

INSTALLATION

NodOn Pilot Wire Heating Module allows to connect any type of pilot wire heater to a compatible EnOcean network. Thanks to its compact size, the Pilot Wire Heating Module can be installed behind the grommet of the pilot wire heater.

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-2TIP
Add the Multifunction Relay Switch to the electric panel with NodOn DIN Rail Box*.

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-3

MODULE INPUTS/OUTPUTS

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-4

Each terminal can accept a cable of 2.5mm² maximum, stripped of 8mm.

INSTALLATION DIAGRAM

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-5

  1. Cut the power supply.
  2. Dismantle the grommet connecting your pilot wire heater.
  3. Cable the module according to diagram figure 1.
    Warning: Make sure the pilot wire of your heater is well connected on the FP terminal before turning the power supply back ON.
  4. Reinstall the grommet.
  5. Turn the power supply back ON.

USE

During the first power up, the module default state is “Comfort” and the LED is green

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-6

To change the mode, press briefly once on the button

Incrementation of the 4 module’s modes

The module LED will blink to confirm the activation of the next mode:

  • Comfort Eco: LED blinks orange once
  • Eco No Frost: LED blinks orange twice
  • No Frost Stop: LED blinks orange 3 times
  • Stop Comfort: LED blinks orange 4 times

Note: Used with a home automation gateway, 6 modes are available: Comfort, Comfort -1°C, Comfort -2°C, Eco, No Frost and Stop. To change the mode, follow the instructions of your home automation gateway

PAIRING PROCEDURE

To add a remote or a wall switch (EnOcean compatible) you must enter the pairing mode. Module must be power supplied

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-8

  1. Launch the pairing by doing 3 consecutive presses (<2 seconds) on the module button. The LED blinks redEnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-9
  2. You have 30 seconds to pair your controller by briefly pressing (in less than a second) on the button of your choice.EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-10
  3. The LED of the module will blink green twice, confirming the pairing of the two devices.

Note: if the LED blinks orange during the pairing procedure, it means that more than 22 controllers are paired and that no more controller can be paired. You must remove one controller to add a new one.

CONTROLLER USE

Your remote works by channel

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-11Your wall switch works by channel

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-12

USE OF YOUR SOFT BUTTON

To pair your Soft Button with the module

  1. Launch the module pairing mode (see “Pairing Procedure”)
  2. You have now 30 seconds to pair your Soft Button by doing 5 brief consecutive presses on the button.
  3. The LED of the module will blink green twice, confirming the pairing of the two devices.

The Soft Button will work as follows

EnOcean-SIN-2-FP-01-Pilot-Wire-Heating-Module-fig-13PAIRING
WITH A HOME AUTOMATION GATEWAY

For more details on how to pair a home automation gateway or other compatible products, please consult the “Support” section on nodon.fr/en/

UNPAIRING PROCEDURE

Do the same procedure as pairing (see “Pairing procedure”).

RESET PROCEDURE

Module must be power supplied.

  1. Press more than 5 seconds on your module’s button. The LED blinks orange.
  2. Press once again the button (short press) to confirm the reset. If the reset is correct, the LED blinks alternatively in red and green and stays green. Start again if necessary.
  3. Your module has now its original settings.

CONTACT
NodOn SAS 121 rue des Hêtres 45590 St CYR EN VAL (FRANCE)

AFTER SALES SERVICE

Documents / Resources

EnOcean SIN-2-FP-01 Pilot Wire Heating Module [pdf] User Guide
SIN-2-FP-01 Pilot Wire Heating Module, SIN-2-FP-01, Pilot Wire Heating Module, Wire Heating Module, Heating Module, Module

References

Leave a comment

Your email address will not be published. Required fields are marked *