Ems Kontrol NR-711 Panel Type Humidity Control Device User Manual

Unpack the product carefully.
Make cable connections according to the provided diagram:
- Supply: LN
- Sensor Connection: Brown, Yellow, White, Green
- Out: NO/NC COM
- A1 A2 CONTACTOR

SET, HYSTERESIS, and NO/NC VALUES

Adjust the set value, hysteresis, and NO/NC values based on your
requirements using the provided controls.

CALIBRATION

Humidity measurement calibration is not user-performed; it is
done at the production site.

If calibration is needed due to communication cable issues
during use, it should be done on the control panel, not on the
product.

FAQ

What is Err?

If no data is received from the sensor for about 15 seconds, an
Err error appears on the display. In this case, check the sensor
connection of the product.

What is NO and NC?

NO (Normally Open) opens the contact below the set value and
closes the contact above the set value. NC (Normally Close) closes
the contact below the set value and opens the contact above the set
value.

SET VALUE DISPLAY

By pressing the SET button, you can view the last set value of
the device.

RELAY POSITION

The green LEDs on the right side of the screen indicate whether
the relay is open or closed. If the LED is on, the relay is open;
if not, the relay is closed.

View Fullscreen

ems kontrol
PANEL TYPE HUMIDITY CONTROL DEVICE
NR-711 USER MANUAL
CO2
www.emskontrol.com

Product Code
NR-711

Output S gnal
Relay (2A)

kk-07.02 rev-1.7 / 20.12.24

WHAT IS IT?
Panel type hum d ty control dev ce allows you to control your hum d ty dev ces n the des red value range by prec sely measur ng the relat ve hum d ty value.
HOW DOES IT WORK?
Operates w th 220 V AC supply. Depend ng on your hum d ty dev ce, you can control your dev ces w th the help of our d rect control dev ce or contactor.
GENERAL FEATURES
Accurate and Prec se Measur ng, 1 Relay Output, Durable and Handy Des gn, Long Operat ng L fe, Cleanable F lter, Panel Type Mount ng, Adjustable Relay Sens t v ty
AREAS OF USE
HVAC Appl cat ons, Poultry Automat on and Poultry Farms, Cold Storage, Incubat on Rooms, Food Storage, A r Cond t on ng Cab nets, Clean Rooms and Laborator es.
RULES TO BE CONSIDERED FOR SAFETY
1- Always read the user manual before us ng the dev ce and ts apparatus. 2- Damages caused by open ng, break ng or m suse of the plast c parts of the dev ce and ts apparatus are cons dered out of warranty. 3- Keep the dev ce and ts apparatus away from external nfluences such as l qu d, h gh dust, h gh temperature, etc. and protect them. 4- Do not expose the dev ce cables to any jamm ng and pressure. 5- D sconnect the electr cal power when your dev ce s not used for a long t me. 6- Our dev ces and apparatus should be used by pay ng attent on to the po nts n the user manual. In case of damages and malfunct ons ar s ng from external use (l qu d contact, fall ng to the ground, etc.) ask for help from the serv ce. 7- Fa lures due to electr cal connect on errors and electr cal voltage or current errors are not covered by the warranty.
B

C b
a A

c
S zes A 103 mm B 72 mm C 36 mm a 93 mm b 66,5 mm c 31,75 mm
2

Techn cal Data

Product Name: Supply Voltage:

Panel Type Hum d ty Control Dev ce
220 V AC

Output:

Relay (2A)

Measurement Range: 0-100 %

Prec s on:

± % 1

Accuracy:

± % 3

Operat ng Temperature: (-10°C) – (+55°C)

Storage Temperature: (-20°C) – (+60°C)

* If the dev ce s to be used outs de the operat ng temperature, the manufacturer must be nformed and approval must be obta ned.

INSTALLATION

1- Unpack the product.

2- Make cable connect ons accord ngly.

Supply
LN

Sensor Connect on
Brown Yellow Wh te Green

Out
NO/ NC COM

1 2 3 4 5 6 7 8 9 10

N L

NO/NC

COM

A1 A2 CONTACTOR
3- Place the product n the appropr ate place on the panel. 4- After the product s energ zed, “OPEN” appears on the d splay for 30 seconds. It starts the measurement process after the “OPEN” text. It s recommended to leave the product n the env ronment for at least 5 m nutes to get healty measurement values. 5- It s recommended to use sh elded cable as commun cat on cable as t w ll prevent commun cat on s gnals from be ng affected by external nfluences. 6- S nce the commun cat on cable w ll create res stance, check the measurement values aga n after cable nstallat on.

SET, HYSTERESIS and NO/NC VALUES
When we press the “SET” button on Set Up the ma n screen, the first menu that appears n the SET menu. In th s menu, the set value can be ncreased Back Down or decreased w th the “UP” and “DOWN” buttons. When the “SET” button s pressed aga n, the HYSTERESIS menu s entered. The hysteres s value can be nscreased or decreased w th the “UP” and “DOWN” buttons. When the “SET” button s pressed aga n, the manu where the relay pos t ons are set appears. You can set “NC” w th the “UP” button and “NO” w th “DOWN” button. “BACK” button s used to go back n menus. If no button s pressed for 10 seconds wh le n a menu entered w th the “SET” button, t returns to the ma n screen.
WHAT IS “Err”?
If no data s rece ved from the sensor for about 15 seconds, an “Err” error appears on the d splay. In th s case, check the sensor connect on of the product.
WHAT IS NO and NC?
NO (Normally Open) opens the contact below the set value and closes the contact above the set value. NC (Normally Close) closes the contact below the set value and opens the contact above the set value.
SET VALUE DISPLAY
By press ng the “SET” button, you can v ew the last set value of the dev ce.
RELAY POSITION
The green leds on the r ght s de of the screen nd cate whether the relay s open or closed. If the led s on, the relay s open, f not, the relay s closed.
CALIBRATION
1- Hum d ty measurement cal brat on cannot be done on the product. Cal brat on s done at the product on s te. 2- The need for cal brat on due to the commun cat on cable dur ng use should be done on the control panel, not on the product.
4

ems kontrol
www.emskontrol.com
USER MANUAL
DECLARATION OF CONFORMITY
Headquarters and place of product on, Halkapinar Mah. 1376 Sok. Boran Plaza No:1/L Konak / ZMR – TÜRKYE, EMS KONTROL ELEKTRONK VE MAKNE SAN. TC. A.. declares that the product marked w th CE, whose name and spec ficat ons are g ven below, covers the spec fied d rect ves and prov s ons. Brand: EMS KONTROL Product Name:NR- 711 Product Type: Panel Type Hum d ty Control Dev ce Compat ble D rect ves: Elektromagnet c Compat b l ty D rect ve 2014/30/EU (EMC EN 61000-6-3: 2007 + A1: 2011, EN 61000-6-1: 2007) Low Voltage D rect ve 2014/35/EU (LVD EN 60730-2-9:2010, EN 60730-1:2011) Add t onal nformat on: Th s product can be used n comb nat on w th other dev ces and compl ance w th the d rect ves covers only the product. EMS KONTROL s not respons ble for the compl ance of ent re system w th the d rect ves. Th s declarat on s not val d f the product s mod fied w thout our approval.
RED
5

WARRANTY TERMS
1- The warranty per od of the dev ces and apparatus starts from the nvo ce date and s guaranteed for 2 years aga nst manufactur ng defects. 2- Dev ces and apparatus are del vered to the customer n work ng cond t on n our company. On-s te comm ss on ng s subject to serv ce fee. 3- The repa r of the dev ces and apparatus under warranty s carr ed out n our company as a result of send ng them w th the transportat on company contracted by our company. In on-s te serv ces, transportat on and accommodat on expenses of the serv ce personnel belong to the customer. The cost of the work ng t me spent on the road s added to the serv ce fee and the collect on s made n advance. 4- Ma ntenance of dev ces and apparatus s done n our company. Transportat on and transportat on fees of the dev ces and apparatus to and from our company for ma ntenance belong to the customer. 5- In case of malfunct on of the dev ces and apparatus whose warranty per od cont nues, whether the malfunct on s caused by the fault of the customer or the manufacturer s tested n our company and reported w th the report to be ssued by our company. 6- In case of detect on of manufacturer- nduced faults of the dev ces and apparatus whose warranty per od cont nues, the customer may request a replacement or may request that the repa r costs of the dev ces and apparatus be fully covered by the manufacturer, prov ded that t does not exceed the product pr ce. 7- In the event that the faults of the dev ces and apparatus whose warranty per od cont nues are determ ned to be caused by the customer, all costs belong to the customer. 8- If the customer does not nd cate that he/she s aware of the defects n the dev ces and apparatus from the date the warranty per od starts or n cases where he/she s expected to be aware, he/she cannot benefit from Art cle 6. 9- Fa lures ar s ng from the use of dev ces and apparatus contrary to the po nts n the user manual are not covered by the warranty. 10- Dev ces and apparatus are not covered by the warranty f they are beaten, broken or scratched by the customer. 11- Damages caused by the use of dev ces and apparatus of other brands and models w thout the approval of the manufacturer are not covered by the warranty. 12- Errors caused by rust ng, ox dat on and l qu d contact due to work ng n dusty / ac d c / hum d env ronments are not covered by the warranty. 13- Damages that may occur dur ng transportat on of dev ces and apparatus are not covered by the warranty. If the customer w shes, he/she can have transportat on nsurance. 14- Damages caused by ma ns voltage / faulty electr cal nstallat on are not covered by the warranty. 15- Dev ces and apparatus are not covered by the warranty n case of malfunct ons caused by force majeure such as fire, flood, earthquake, etc.
6

16- All parts of the dev ces and apparatus, nclud ng all parts, are covered by our company’s warranty. 17-If the dev ces and apparatus malfunct on w th n the warranty per od, the t me spent n repa r shall be added to the warranty per od. The repa r per od of the goods shall not exceed 20 work ng days. Th s per od starts from the date of not ficat on of the malfunct on of the goods to the serv ce stat on, n the absence of a serv ce stat on, to the seller, dealer, dealer, agent, representat ve, mporter or manufacturer – manufacturer of the goods. It s poss ble for the consumer to not fy the malfunct on by telephone, fax, e-ma l, reg stered letter w th return rece pt or s m lar means. However, n case of d spute, the burden of proof belongs to the consumer. If the malfunct on of the goods s not resolved w th n 20 bus ness days, the manufacturermanufacturer or mporter; unt l the repa r of the goods s completed, another goods w th s m lar character st cs must be allocated to the use of the consumer. 18- Desp te the consumer’s r ght to repa r the goods; -Prov ded that t s w th n the warranty per od from the date of del very to the consumer, t fa ls at least four t mes w th n a year or s x t mes w th n the warranty per od determ ned by the manufacturer-manufacturer and / or mporter, as well as the fact that these fa lures make the nab l ty to benefit from the goods cont nuous, -Exceed ng the max mum t me requ red for repa r, -If t s determ ned that t s not poss ble to repa r the malfunct on w th the report to be ssued by the serv ce stat on of the company’s serv ce stat on, f the serv ce stat on s not ava lable, respect vely by one of ts dealer, dealer, agency, representat ve, mporter or manufacturermanufacturer, t may request a refund or a pr ce reduct on at the rate of defect. 19-Customer may file compla nts and object ons to consumer courts or consumer arb trat on comm ttees. 20-The warranty cert ficate must be kept by the customer dur ng the warranty per od. In case of loss of the document, a second document w ll not be ssued. In case of loss, repa r and replacement of dev ces and apparatus w ll be made for a fee.
Th s dev ce s a Waste Electr cal and Electron c Dev ce accord ng to the d rect ves appl ed n Europe 2002/96/EC. (WEEE) Before scrapp ng or throw ng away th s dev ce, you must prevent ts potent al negat ve consequences for the env ronment and human health. Otherw se t would be nappropr ate waste. Th s symbol on the product s ntended to warn that the product should not be treated as household waste and should be del vered to electr cal and electron c waste collect on po nts. D sposal of the product must be done n accordance w th local env ronmental regulat ons. You can obta n deta led nformat on from author zed un ts on how to destroy, reuse and recycle the product..
7

Manufacturer’s

T tle: EMS KONTROL ELEKTRONK VE MAKNE SAN. VE TC. A..

Address: Halkapinar Mah. 1376 Sokak Boran Plaza No:1/L Konak / zm r-TÜRKYE Telephone: 0 (232) 431 2121 E-Ma l: nfo@emskontrol.com

Company Stamp:

STAMP

Product’s
Type: Panel Type Hum d ty Control Dev ce Brand: EMS Kontrol Model: NR-711 Warranty Durat on: 2 Years Max mum Repa r T me: 20 Days Banderol and Ser al Number:

Vendor Company T tle: . …………………………………………………. Address: ……………………………………………… Telephone:………………… Faks:………………… E-Ma l:…………………………………………………. Invo ce Date and Number:………………………. Del very Date and Place:………………………… S gnature of Author sed Person:………………….. Company Stamp:……………………………………
STAMP

Product’s Type: Panel Type Hum d ty Control Dev ce Brand: EMS KONTROL Model: NR-711

EMS Kontrol reserves the r ght to make changes and mprovements to the product spec ficat ons and user manual.

*For all changes, please v s t emskontrol.com.

ems

kontrol

www.emskontrol.com

Documents / Resources

Ems Kontrol NR-711 Panel Type Humidity Control Device [pdf] User Manual
NR-711, kk-07.02 rev-1.7, NR-711 Panel Type Humidity Control Device, NR-711, Panel Type Humidity Control Device, Humidity Control Device, Control Device, Device

References

User Manual

NR-711 Panel Type Humidity Control Device

Specifications

Product Usage Instructions

Installation