EMOS H5101 Series Wifi Switch Module Instruction Manual

Safety Instructions and Warnings:
Ensure the Wi-Fi network is operating at 2.4 GHz when connecting the module. For ZigBee modules, connect them to a ZigBee gateway linked to a 2.4 GHz Wi-Fi network.

Installation and Assembly:
Place the module in the installation box under a switch or socket. Fix the module securely for other installation locations. Strip all connected cables to a length of 7 mm for safety.

Pairing with an Application:

Open the EMOS GoSmart app, confirm privacy policy, and select registration.

Enter a valid email and password, confirm privacy policy, and register.
Select ‘Add device,’ choose product category, and select Smart Switch (ZigBee) / Smart Switch (Wi-Fi) device.

[For ZigBee module only] Select the ZigBee gateway in the app and reset the module for pairing.
After successful pairing, name the module as needed using the app.

Controls and Functions:

Switch button (ON/OFF): Long press to rename the button

Advanced settings, Timers, Module settings

FAQ

Troubleshooting:
Contact customer support for technical assistance or refer to the troubleshooting section in the manual for common issues and solutions.

Safety instructions and warnings

Before using the device, read the instructions for use.
Observe the safety instructions in this manual.

EMOS spol. s r.o. declares that the products H5101, H5102, H5103, H5104, H5105, H5106 are in compliance with the basic requirements and other relevant provisions of the directives. The equipment can be freely operated in the EU. The Declaration of Conformity can be found on the website http://www.emos.eu/download.
The equipment can be operated on the basis of general authorisation No. VO-R/10/07.2021-8 as amended.

Package contents

Switching module
Manual

Technical specifications

Power supply: AC 100-240 V 50/60 Hz
Dimension: 40 × 40 × 18 mm

Net weight: 30 g
App:EMOS GoSmart for Android and iOS Connectivity: 2.4 GHz Wi-Fi (IEEE802.11b/g/n) / Zigbee 2402 ~ 2 480 MHz

Frequency band: 2.400-2.4835 GHz

Description of the device

RESET button

Holes for mounting
Wiring diagram of the relevant module
LED status light
- Flashing blue – Device is in pairing mode / has disconnected from the network
- Illuminated blue – Device is in operating mode 5 – Terminal block for wiring connection

Notice
It is strongly recommended that the Smart Switch Module be installed by a knowledgeable person. Poorly executed installation can pose a risk of electric shock. Carefully follow the following instructions and observe the maximum equipment loads listed below to ensure safe and proper operation.

Maximum load

channel module with LN wires – LED 300 W, 10 A
2 channel module with LN wires – LED 2×150 W 2×5 A
1 channel module without N wire – 10-100 W
2 channel module without N wire – 2× (10-100 W)

Wi-Fi modules
Make sure that the Wi-Fi network you are connecting the module to is operating at 2.4 GHz, not 5 GHz.

ZigBee modules
For ZigBee modules to work, they must be connected to a ZigBee gateway. The ZigBee gateway itself must be connected to a 2.4 GHz Wi-Fi network.

Installation and assembly

Place the connected module in the installation box under a switch or socket. Thanks to the possibility of fixing, the module can also be installed in various other places (e.g. under plasterboard, in the ceiling…) The wiring diagram can be found below.

For functional and safety reasons, it is essential that all cables connected to this module are stripped at the end to a length of 7 mm.
Wiring diagrams for Wi-Fi and ZigBee switch modules with LN wires (H5101, H5102, H5105, H5106)
Wiring diagrams for Wi-Fi and ZigBee switch modules without N wire (H5103, H5104)

Pairing with an application

Installing the EMOS GoSmart app

The app is available for Android and iOS via Google play and the App Store.

Please scan the QR code to download the app.
Open the EMOS GoSmart app and confirm the privacy policy by clicking Agree. Select the registration option.

Enter the name of a valid email address and choose a password. Confirm your consent to the privacy policy. Select register.

Pairing with an app

Select Add device.

Select a GoSmart product category and select a Smart Switch (ZigBee) / Smart Switch (Wi-Fi) device.
[For ZigBee module only] Select the ZigBee gateway you want to pair the module with. This gateway must be added in the application before pairing the module.

Reset the module by holding down the RESET button for 5 seconds or by flipping the physical switch 6 times (6 times on-off) and checking that the LED is flashing.
The device will be automatically searched.

After successful pairing, the app displays a confirmation screen. Use the pencil icon to name the module according to your needs.

Controls and functions

Icons and indicator lights

Switch button (ON/OFF)
*Long press to rename the button

Description of extension settings

Device information – Basic information about the device and its owner
Tap-to-Run and Automation – View scenes and automations assigned to the device. Creation of scenes is possible directly in the main menu of the application in the section “Scenes”.

Offline Notification – To avoid constant reminders, a notification will be sent if the device remains offline for more than 30 minutes.
Multi-Control association – Device grouping
Share Device – Share device management to another user

FAQ & Feedback – View the most common questions along with their solutions plus the ability to send a question/suggestion/feedback directly to us
Add to Home Screen – Add an icon to your phone’s home screen. With this step, you don’t have to open your device through the app every time, but just click directly on this added icon and it will take you straight to the module

Timer settings

Countdown – The device turns off/on after a set time (Depending on the current switch-on status)
Schedule – Scheduling automatic switch-on according to the set time (e.g. Monday from 13:00 to 15:00 – On; 15:00-17:00 – Off…)

Circulate – Circulate between ON and OFF in a time period with ON and OFF length settings (e.g. you have a fish tank where you need the filtration on for 30 minutes every hour -> In the app you set the Start Time to 8:00 and End Time to 20:00 so that the filtration does not disturb you at night. Open time is the time the device will be on, in our case 30 minutes filtration and Close time would be the hour during which the filtration will be off).
Random – The module turns on at random times for random lengths of time from – to. (Illusion that someone is in the house)
Inching – Once set, the module turns off after the set time has elapsed.

Module settings

Relay status – Module behavior after power failure.

Switch Type settings – Settings according to your physical switch type.
Rocker switch – Flip to change status – The on/off position is set according to the current position of the physical switch. So if the module is on and the switch is pressed “Up”, then Up = On. If the module is off, then Up = Off. Same with the “Down” position.

Rocker switch – State synchronous – Sets the on/off position according to the actual switching of your physical switch. So if the switch is on, the module will turn on and vice versa.
Button Switch – A one-button switch that returns to its original position. 1st press = on, 2nd press = off.

Troubleshooting FAQ

I can’t get the devices to pair. What can I do?
- Make sure you are using a 2.4GHz Wi-Fi network and have a strong enough signal
- Allow the app all permissions in the settings
- Make sure you are using the latest version of the mobile operating system and the latest version of the app
What can I control with the module?
- Most small household electrical appliances such as lamps, sockets, coffee machines etc.
- Please note the maximum load indicated directly on the module. We therefore do not recommend installing the module to control larger devices such as electric motors, pumps, boilers…
What should I do if I change my Wi-Fi network or password?
The module needs to be reset and paired with the application again.
What happens if the Wi-Fi network stops working?
If you also have a physical switch connected to the module, the device can still be controlled without any problems. However, you will not be able to control the modules through the app until the Wi-Fi network is up and running. The exception to this is ZigBee modules that can still be controlled remotely with other ZigBee devices, such as the EMOS H5011 Scenic Switch, even after an internet outage.

Documents / Resources

EMOS H5101 Series Wifi Switch Module [pdf] Instruction Manual
H5101, H5102, H5103, H5104, H5105, H5106, H5101 Series Wifi Switch Module, H5101 Series, Wifi Switch Module, Switch Module, Module

References

User Manual

EMOS H5101 Series Wifi Switch Module

Product Specifications

Product Usage Instructions

FAQ