DESCRIPTION

E-2000M Series general purpose process controllers are industrial devices in 1/4 DIN (96×96 mm IEC/TR 60668) dimensions designed by using new generation microcontrollers with on/off, PID and other control forms. Inputs and outputs can be easily programmed by the user.
In E-2000M Series controllers, set value and measured value can be displayed from -1999 to 9999 on two 4-digit displays and general purpose inputs (T/C, R/T, mV, mA) can be programmed.

DIMENSIONS and PANEL CUT-OUT

CONNECTION DIAGRAM

1st and 2nd control outputs can be selected as either Relay (RL1, RL2) or SSR (SSR1, SSR2).
Analog output (AO1) can be selected as either mA or 0-10 V DC.

WARNING

E-2000M controller is designed for panel mounting and should be used in an industrial environment.

• The package of E-2000M controller contains; Controller,2 pieces of mounting clamps, User manual and Guarantee certificate
• After opening the package, please check the contents with the above list. If the delivered product is wrong type, any item is missing or there are visible defects, contact the vendor from which you purchased the product.
• Before installing and operating the controller, please read the user manual thoroughly.
• The installation and configuration of the controller must only be performed by a person qualified in instrumentation.
• Keep the unit away from flamable gases, that could cause explosion.
• Do not use alcohol or other solvents to clean the controller. Use a clean cloth soaked in water tightly squeezed to gently wipe the outer surface of the controller.
• It is not used in medical applications.

EU DIRECTIVE COMPLIANCE
Low Voltage Directive: EN 61010-1
EMC Directive: EN 61326-1TS EN ISO 9001
Quality Management System Certificate

TYPE CODING

E-2000M Series Universal Advanced Controller
Relay Outputs
None
1 relay (RL1)
2 relays (RL1, RL2)
1 SSR (SSR1)
1 SSR (SSR1) + 1 relay (RL2)
2 SSR (SSR1, SSR2)
Analog Outputs
None
0-20 / 4-20 mA (AO1)
0-10 V DC (AO1)
Communication
None
Operating Voltage
85-265 V AC / 85-375 V DC
20-60 V AC / 20-60 V DC

TECHNICALSPECIFICATION

Parameter	Description
Control Type	On/Off, PID, Heat/Cool, Floating Control of Valves
Operating Voltage	20..60 V AC / 20..60 V DC or 85..265 V AC / 85..375 V DC
Relays / SSR	2 x SPST – NO 250 V AC 5A or 24 V DC 25 mA (SSR) drives
Dimensions (mm)	96 (Lenght) x 96 (Height) x 50 (Width)
Panel Cut-Out (mm)	92 (Lenght) X 92 (Height)
Analog Output	1 x 0..20 / 4-20 mA or 0..10 V DC optional
Analog Input	Universal (Note 1)
Communication (RS-485)	None
Digital Input	None
Valve Feedback	None
Transmitter Supply	None
Weight	230 g
Power Consumption	Max. 7 W (10 VA)
Operating Temperature	– 10 °C … 55 °C
Storage Temperature	– 25 °C … 65 °C
Memory	Maks. 100.000 write
Protection Class	IP-65 Front Panel, IP-20 Rear Case

Notes:
(1) Universal Input :
Thermocouple: B, E, J, K,L, N, R, S, T, U
Resistance Thermometer: Pt-100
Current: 0-20 mA, 4-20 mA (Linear)
Voltage: 0-50 mV, 0-1 V, 0.2- 1 V (Linear),
0-10 V DC, must be specified in the order.
Resolution: 16 bit
Accuracy: Thermocouple, Max. +1.0 °C (Conversion and CJC error)
Resistance Thermometer, Max. 0.5 °C (Conversion and wire resistance compensation)
Linear Input, Max. % 0.1

PARAMETER TABLE

		Description		Min	Maks	Unit
INPUT SETTINGS			Analog Input 1 Type	Table 1
			Decimal Point	0	3
			Analog Input 1 Linear Scale Lower Value	-199.9	999.9	EU
			Analog Input 1 Linear Scale Upper Value	-199.9	999.9	EU
			Temperature Unit
			Analog Input 1 Offset Value	-100.0	100.0	EU
			Analog Input 1 Filter	1	15	s
			Analog Input 1 Sensor Broken Behaviour

CONTROL SET SETTINGS			Control Set Point Source	Table 2
			Control Set Point Lower Limit	-199.9		EU
			Control Set Point Upper Limit		999.9	EU
			Control Set Point Ramping Rate		60.0	EU/min
			1. Step Set Value			EU
			1. Step Time		999.9	min
			2. Step Set Value			EU
			2. Step Time		999.9	min
			3. Step Set Value			EU
			3. Step Time		999.9	min

ALARM SETTINGS			Alarm 1 Type	Table 3
			Alarm 1 Set Point	-199.9	999.9	EU
			Alarm 1 Hysteresis	0.0	999.9	EU
			Alarm 1 Lock
			Alarm 2 Type	Table 3
			Alarm 2 Set Point	-199.9	999.9	EU
			Alarm 2 Hysteresis	0.0	999.9	EU
			Alarm 2 Lock

OUTPUT SETTINGS			Control Type	Table 4
			Control Form []
			Control Period	1	250	s
			Manual Mode Selection
			Floating Control Valve Travel Time	10	2500	s
			Dead Band	0.1	25.0	%
			Control Output Lower Limit	0.0		%
			Control Output Upper Limit		100.0	%
			Control Output Manual Reset			(Y0
			PID Power On Behaviour	0	4
			Retransmission Scale Lower Value	-200.		EU
			Retransmission Scale Upper Value		1000.	EU
			Relay 1 Function	Table 5
			Relay 2 Function	Table 5
			Analog Output 1 Function	Table 6
			Analog Output 1 Type	Table 7.1 ve Table 7.2

PID SETTINGS			PID Auto Tune
			PID Parameter Type
			Proportional Band +	0.1	999.9	EU
			Proportional Band –	0.1	999.9	EU
			Integral Time +		9999	s
			Integral Time –		9999	s
			Derivative Time +		2500	s
			Derivative Time –		2500	s
			Hysteresis	0.0	999.9	EU

SECURITY			Security Code	0	9999
			Parameter Access Level	0	9
			Parameter Setting Level	0	9
			Factory Settings []

ACCESSING PARAMETERS

APPLICATION EXAMPLES

1. Input: Pt-100 Relay / Alarm1: 50 °C Low, Relay2 / Alarm2: 55 °C High
   AO1: 4-20 mA PID Control Output
2. Input: TC Type J, Relay1: On-Off Control Output, Relay2 / Alarm2: 350 °C High
3. Input: TC Type K, Profile Control (Ramp up to 400°C in 10 minutes and wait for 60 minutes),
   Relay1: PID Control Output, AO1: Retransmission Output (4-20 mA, 0-1200 °C)

Table 1. Input Type Options
	Type B Thermocouple
	Type E Thermocouple
	Type J Thermocouple
	Type K Thermocouple
	Type L Thermocouple
	Type N Thermocouple
	Type R Thermocouple
	Type S Thermocouple
	Type T Thermocouple
	Type U Thermocouple
	Pt-100
	0-20 mA
	4-20 mA
	0-50 mV
	0-1 V
	0.2-1 V
	0-10 V (*)
	2-10 V (*)

(*) Custom specified volt input

Table 2. Control Set Options
	Internal adjustment with keys
	With Profile Control

Table 3. Alarm Options
	Off
	Low Alarm
	High Alarm
	Low Deviation
	High Deviation
	Band Alarm (In)
	Band Alarm (Out)

Table 4. Control Type Options
	No Control
	Single (Heat)
	Double (Heat/Cool)
	Floating Control of Valve

Tablo 5. Relay Output Options
	PID + (Heating)
	PID – (Cooling)
	On-Off + (Heating)
	On-Off – (Cooling)
	Alarm 1
	Alarm 2
	Alarm 3
	Alarm 4

Table 6. Analog Output Options
	PID + (Heating)
	PID – (Cooling)
	Process Value
	Control Set Value

Table 7.1. Analog Output Range
	0-20 mA
	20-0 mA
	4-20 mA
	20-4 mA

Table 7.2. Analog Output Range
	0-10 V
	10-0 V
	2-10 V
	10-2 V

For detailed information, you can access the comprehensive user manual of the device under the heading “User Manuals” at www.elimko.com.tr.
You can also use the QR Code on the front for this.

Manufacturer / Technical Support : Elimko Co. Ltd.
8. Cadde 21. Sokak No:16 06510 Emek / ANKARA – TURKEY
Phone:+ 90 312 212 64 50 Fax:+ 90 312 212 41 43
www.elimko.com.tr e-posta: elimko@elimko.com.trhttps://elimko.com.tr/en/technical-support/user-manuels 

Documents / Resources

Elimko E-2000M Universal Advanced Controller [pdf] User Guide E-2000M Universal Advanced Controller, E-2000M, Universal Advanced Controller, Advanced Controller, Controller

References

• User Manual