ELGENS Wide Temperature TDM Series P-CAP Touch LCD Monitor User Manual
Warning!
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in whichcase the user at his own expense will be required to take whatever measures may be required to correct the interference.
Electric Shock Hazard – Do not operate the machine with its back cover removed. There are dangerous high voltages inside
Disclaimer
This information in this document is subject to change without notice. In no event shall ELGENS Co., Ltd. be liable for damages of any kind, whether incidental or consequential, arising from either the use or misuse of information in this document or in any related materials
Packing List
Accessories (as ticked) included in this package are:
- Panel Mounting Kits
- 3 Pin Male Terminal Block
- Optional Adapter
- Other.___________________(please specify)
Safety Precautions
Follow the messages below to avoid your systems from damage:
- Avoid your system from static electricity on all occasions.
- Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use.
- Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system
ELGENS WEEE, ROHS and REACH Compliance Statement
When it comes to product design, the engineering team at ELGENS strives for energy efficiency and environmental friendliness–not only because it lowers monthly power costs for our customers, but also to ensure minimal energy consumption for a greener tomorrow.
Though our products (no including customer consigned materials) are not officially certified, they are in fact compliant with WEEE, RoHS and REACH standards. This means we take care to properly recycle all unused material and end-of-life products, as well as minimize the use of potentially hazardous substances.
It is not required by law that certain fixed industrial plant equipment and tools entirely omit the use of lead, mercury, cadmium, and hexavalent chromium and flame retardants such as polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE). However, ELGENS assumes the responsibility to restrict the inclusion of these resources in all products, meeting the requirements of RoHS and WEEE standards.
ELGENS., Co Ltd 戎克東方科技股份有限公司
Chief Executive Officer 執行長
Santiago Li 李金柱
Date：2017 /9 /21
General Descriptions
Datasheet
| Title | 10.1”~24” Touch monitor with IP65 front bezel, Auto Light sensor(Option), DP/VGA/HDMI, Panel Mounting kits , DC 12V input by 3-pin terminal block | |||
| Feature |
|
|||
| Specification | ||||
| Touch Screen | P-cap by USB interface (self-capacitance function include, Supports Win 10, 8, 7, XP / Linux / Android OS) | |||
| Power Input | 3-Pin Power Input Terminal Block
DC 12V Power Input, Optional DC9~36V Wide Voltage Power Input Fuse / Input reverse / Over current / Output short circuit protection |
|||
| Mounting |
|
|||
| Vibration | 1.5 Grms @10~500Hz, IEC-60068-2-64 | |||
| Shock | Half-sine, 3G @ 11ms, IEC-60068-2-27 | |||
| Operating Temp | -40 ~ 80 °C，IEC-60068-2-1/2/14 | |||
| Humidity | 10~90% @40 °C, non-condensing | |||
| Ordering Code | ||||
| Model Number | Description | |||
| TDM-P101WT
TDM-P104ST TDM-P121ST TDM-P150ST |
10.1″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin
terminal block DC 12V adapter 10.4″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter 12.1″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter 15.0″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter |
|||
| TDM-P156WT
TDM-P170ST TDM-P173WT |
15.6″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter
17.0″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter 17.3″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter |
|||
| TDM-P185WT
TDM-P190ST TDM-P215WT TDM-P240WT |
18.5″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin
terminal block DC 12V adapter 19.0″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter 21.5″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter 24.0″ touch monitor with IP65 front bezel, DP / VGA / HDMI, Panel mounting kits, 3-pin terminal block DC 12V adapter |
|||
General instructions
- Support Vertical refresh rate up to 75Hz for VGA~SXGA+(1400×1050) and 60Hz for higher resolution of VESA Standard Timing.
- Support VGA analog standard input (15-pin D-Sub connectors).
- Automatic detection of separate synchronize and composite synchronizes of VGA.
- Support Display Port input (DP)
- Support High-Definition Multimedia Interface (HDMI) input .
- RoHS compliant .
- Support Timing Table O
Mode Resolution H Freq.(KHz) V Freq.(Hz) 1 640*350@70 31.469 70.087 2 640*480@60 31.469 59.940 3 640*480@72 37.861 72.809 4 640*480@75 37.500 75.000 5 720*400@70 31.469 70.087 6 800*600@56 35.156 56.250 7 800*600@60 37.879 60.317 8 800*600@72 48.077 72.188 9 800*600@75 46.875 75.00 10 1024*768@60 48.363 60.004 11 1024*768@70 56.476 70.069 12 1024*768@72 58.038 71.918 13 1024*768@75 60.023 75.029 14 1280*70@50 36.91 49.82 15 1280*720@60 44.62 59.81 16 1280*1024@60 63.980 60.000 17 1280*1024@70 74.882 69.853 18 1280*1024@75 79.976 75.025 19 1360*768@60 47.72 59.799 20 1440*900@60 55.935 59.887 21 1680*1050@60 65.3 60 22 1920*1080@50 56.25 50.00 23 1920*1080@60 66.6 60
I/O Connect
I/O Connect
Block Diagram
OSD Setting
Power on LED : Off /Orange , On/Green
On/Off : Power On/Off Monitor
Menu/Enter : Open OSD , Enter , Save
Increase : Select item , Increase value
Decrease : Select item , Decrease value
OSD MAP
| Main | Second | Select Items | Defaul |
| Color | Contras t | 0%~ 100% | 50% |
| Brightnes s | 0%~ 100% | 100% | |
| Color Adjust | Red 0%~ 100% | 50% | |
| Green 0%~ 100% | 50% | ||
| Blue 0%~ 100% | 50% | ||
| Color Temp | 9300/6500/5800/US ER | US ER | |
| Auto Color | Color Adjust | ||
| Image Setting | Clock | 0%~ 100% | 50% |
| Phase | 0%~ 100% | 29% | |
| Sharpness | 0/1/2/3/4 | 2 | |
| H.Position | 0%~ 100% | 50% | |
| V.Position | 0%~ 100% | 50% | |
| OSD Menu | OS D H.P os . | 0%~ 100% | 50% |
| OS D V.P os . | 0%~ 100% | 50% | |
| OS D Timer | 5 – 60 s ec | 10 Sec | |
| Language | Englis h/Franqais /Deuts ch/Es panol/繁體中文/简体中文/ 日本語 | English | |
| Signal Source | D-S UB/HDMI/DVI/Auto S earch | Auto Search | |
| Reset |
OSD Operation
How to reconfigure
- Press the “MENU/Enter” button to activate the OSD menu.
- Press the “+” / ”–“ button to navigate through the functions. Select the highlight and desired function and press the “MENU/Enter” button to activate it. If the function selected has a sub-menu, also press the “+” / ”–“ button to navigate through the sub-menu functions and select the highlight and desired sub-menu function and press the “MENU/Enter” button to activate it.
- Press the “+” / ”–“ button to change the settings of the selected function.
- To save the OSD menu, press the “MENU/Enter” button and press the Auto/Exit until OSD menu disappears.
- Repeat steps 1-3 to adjust other settings.
OSD function introduction
A. Color
Set a desired color setting from this menu.
- Contrast : the adjusting range is from 0 to 100.
- Brightness : the adjusting range is from 0 to 100.
- Color Adjust :
Red: the adjusting range is from 0 to 100.
Green: the adjusting range is from 0 to 100.
Blue: the adjusting range is from 0 to 100.
- Color Temp : contains 4 modes including 9300K, 6500K, 5800K and user
- Auto Color : Automatically adjusts the image to its optimized position, clock, and phase. (Only run on D-Sub input Mode)
B. Image Setting (Only run on D-Sub input Mode)
Set the image related setting from this menu.
- Clock : the adjusting range is from 0 to 100
- Phase : the adjusting range is from 0 to 100
- Sharpness : the adjusting range is from 0 to 4
- H.Position : the adjusting range is from 0 to 100
- V.Position : the adjusting range is from 0 to 100
C. OSD Menu
Adjusts the OSD location and language
- OSD H.Pos.: Adjusts the horizontal position (H-Position) of the OSD from 0 to 100.
- OSD V.Pos.: Adjusts the vertical position(V-Position) of the OSD from 0 to 100
- OSD Timer: Adjusts the OSD timeout from 5 to 60 seconds.
- Language: There are 7 languages for your selection, including English, French, Deutsch, Espanol Traditional Chinese, Simplified Chinese, Japanese
D. Signal Source:
In this function, you can select your desired input source
E. Signal Source:
In this function, you can reset all setting to default value
Panel Mounting Installation
Panel Mounting Kits Information
- a. Item 1 : Monunting Kits
- b. Item 2 : Panel Mount PPC
5mm Panel Monunt Panel PC
- Customers can fix Panel PC with their fixture by M3 screws.
- VESA mount holes are also available for mounting from back side
Preparation
- a. Item 1 : Screwdriver
- b. Item 2 : Cut out Area
Installation Steps
Documents / Resources
 |
ELGENS Wide Temperature TDM Series P-CAP Touch LCD Monitor [pdf] User Manual Wide Temperature TDM Series P-CAP Touch LCD Monitor, Wide Temperature, TDM Series P-CAP, Touch LCD Monitor, LCD Monitor, Monitor |
