ELATION 170IP Pixel Driver User Guide

ELATION 170IP Pixel Driver User Guide

ELATION 170IP Pixel Driver User Guide

©2023 ELATION PROFESSIONAL all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ELATION brands and product names are trademarks or registered trademarks of their respective companies.

ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.

Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040 323-582-3322 | 323-832-9142 fax | www.elationlighting.com | info@elationlighting.com

Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands +31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | info@elationlighting.eu

Elation Professional Mexico | AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000 +52 (728) 282-7070

DOCUMENT VERSION

ELATION 170IP Pixel Driver User Guide - QR Code
https://www.adj.com/hydro-beam-x1

Due to additional product features and/or enhancements, an updated version of this document may be available online. Please scan the QR Code with your mobile device or visit www.elationlighting.com for the latest revision/update of this manual, before installation and/or programming.

ELATION 170IP Pixel Driver User Guide - DOCUMENT VERSION

GENERAL INFORMATION

INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this device. These instructions contain important safety and use information. This device is intended for use only by professionally trained personnel, and is not suitable for private usage.

UNPACKING
Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton has been damaged, carefully inspect the device for damage, and be sure all accessories necessary to install and operate the device have arrived intact. In the event that damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this device to your dealer without first contacting customer support. Please do not discard the shipping carton in the trash. Please recycle whenever possible.

BOX CONTENTS

  • UC IR24EL Remote (x1)
  • Adapter Cable, 0.5m (x1)
  • Omega Bracket (x1)

CUSTOMER SUPPORT Contact ELATION Service for any product related service and support needs. Also visit forums.elationlighting.com with questions, comments, or suggestions.
ELATION SERVICE USA – Monday – Friday 8:00am to 4:30pm PST 323-582-3322 | Fax 323-832-9142 | support@elationlighting.com
ELATION SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET +31 45 546 85 63 | Fax +31 45 546 85 96 | support@elationlighting.eu
REPLACEMENT PARTS – please visit parts.elationlighting.com

⚠ IMPORTANT NOTICE!
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/ OR REPAIRS.

IP65 RATED

The International Protection (IP) rating system is commonly expressed as “IP” (Ingress Protection) followed by two numbers (i.e. IP65), where the numbers define the degree of protection. The first digit (Foreign Bodies Protection) indicates the extent of protection against particles entering the fixture, and the second digit (Water Protection) indicates the extent of protection against water entering the fixture. An IP65 rated lighting fixture is designed and tested to protect against the ingress of dust (6), and low-pressure water jets from any direction (5).

NOTE: THIS FIXTURE IS INTENDED FOR TEMPORARY OUTDOOR USE ONLY!
Maritime/Coastal Environment Installations: A coastal environment is seaside adjacent, and caustic to electronics through exposure to atomized salt-water and humidity, whereas maritime is anywhere within 5-miles of a coastal environment.
⚠ NOT suitable for maritime/coastal environment installations. Installing this fixture in a maritime/coastal environment may cause corrosion and/or excessive wear to the interior and/or exterior components of the fixture. Damages and/or performance issues resulting from installation in a maritime/coastal environment will void the manufactures warranty, and will NOT be subject to any warranty claims and/or repairs.
Maritime installations require additional preparation, and additional service intervals may be needed given the maritime use. In general, IP ratings presuppose freshwater conditions VS maritime conditions, which are typically more “caustic” to IP fixtures (both internally and externally). A duty-cycle may also be needed when units are not in use. During times of high humidity and colder temperatures, condensation may occur internally so the fixture may require a duty-cycle to bring it up to running temperature, allowing any accumulation of moisture to be expelled via the vent valve. Recommendations can change based on installation environmental circumstances. A waterproof dome or similar device is recommended for use in permanent outdoor installations. When using a dome, refer to manufacturer recommendations for duty-cycle.

Exterior Maintenance: Inspect the exterior every 30-days. The unit must be powered off/disconnected. The chassis should be inspected for any signs of contaminants. Inspect optics to determine if the lens is obstructed, then clean optics and chassis accordingly. Based on initial finding, schedule maintenance accordingly, keeping in mind that exterior maintenance will be required. Even if the luminaires are NOT in use, maintenance will still be needed given its location (exterior use). The use of a durable type of wax on the chassis is recommended since it will help prevent contaminant build up. Inspect both power and data lines for any signs of contaminants or corrosion. Periodically reapplying di-electric grease, especially in coastal environments. If any signs of corrosion/contaminants are present, clean thoroughly, and/or replace connectors, then reapply di-electric grease. Typically, this should be done annually, or any time an opportunity presents itself. As a preventive measure, annual replacement of both vent valves is recommended. The vent valve membrane can become contaminated and/or clogged causing improper venting of humidity within the luminaire. Inspect all mounting hardware as a precaution.

Interior Maintenance: Inspect the interior every 30-days. The unit must be powered off/disconnected.

  • Inspect zoom/focus mechanism, clean optics, lubricate linear bearings (Krytox oil) as needed, inspect belts for wear
  • Inspect all rotating effect wheels, manually rotate them, note any resistance
  • Inspect all remaining rotating belts for any wear
  • Inspect all fans, clean as needed, check rotation, check connections
  • Inspect CMY module, manually move flags and check for signs of resistance, and if needed, clean guide rods first, then reapply a thin layer of grease (moly lube)
  • Clean interior with low-volume compressed air, then clean optics prior to reassembly of head covers

Although the base has limited moving parts, the pan belt should also be inspected for wear. Remember to always perform an IP test anytime a cover is removed.
There is no specific time frame regarding the routine replacement of parts such as belts/stepper motors, PCBs, or LEDs. These items should only be replaced on an as needed bases, except for cooling fans, which should be replaced once the luminaries reach 10,000-hours. This is a prophylactic measure intended to keep the unit running as cool as possible, insuring proper function of all internal components. A complete service breakdown is available, please contact service@elationlighting.com for any needed parts or manuals.

LIMITED WARR ANTY (USA ONLY)

  • A. Elation Professional hereby warrants, to the original purchaser, Elation Professional products to be free of manufacturing defects in material and workmanship for a period of two years (730 days), and Elation Professional product rechargeable batteries to be free of manufacturing defects in material and workmanship for a period of six months (180 days), from the original date of purchase. This warranty excludes discharge lamps and all product accessories. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
  • B. For warranty service, send the product only to the Elation Professional factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional will pay return shipping charges only to a designated point within the United States. If any product is sent, it must be shipped in its original package and packaging material. No accessories should be shipped with the product. If any accessories are shipped with the product, Elation Professional shall have no liability what so ever for loss and/or or damage to any such accessories, nor for the safe return thereof.
  • C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is modified in any manner which Elation Professional concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional; if the product is damaged because not properly maintained as set forth in the product instructions, guidelines and/or user manual.
  • D. This is not a service contract, and this warranty does not include any maintenance, cleaning or periodic check-up. During the periods as specified above, Elation Professional will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional. All products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that effect.
  • E. Elation Professional reserves the right to make changes in design and/or performance improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
  • F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with the products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professional in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty periods set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said periods have expired. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional be liable for any loss and/or damage, direct and/or consequential, arising out of the use of, and/or the inability to use, this product.
  • G. This warranty is the only written warranty applicable to Elation Professional products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.
    WARRANTY RETURNS All returned service items whether under warranty or not, must be freight pre-paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem, as well as the R.A. number, must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without an R.A. number clearly marked on the out-side of the package will be refused and returned at customer’s expense. You may obtain an R.A. number by contacting customer support.

SAFETY GUIDELINES

This fixture is a sophisticated piece of electronic equipment. To guarantee smooth operation, it is important to follow all instructions and guidelines in this manual. Elation Professional is not responsible for injury and/or damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. Only qualified and/or certified personnel should perform installation of this fixture and only the original rigging parts included with this fixture should be used for installation. Any modifications to the fixture and/or the included mounting hardware will void the original manufacturer’s warranty and increase the risk of damage and/or personal injury.

ELATION 170IP Pixel Driver User Guide - SAFETY GUIDELINES

FOR YOUR OWN PERSONAL SAFETY, PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE ATTEMPTING TO INSTALL OR OPERATE THIS UNIT!

  • Be sure to save the packing carton in the unlikely event that the device may need to be returned for service.
  • Be sure that the voltage of the power source matches the required voltage for the device.
  • Do not open up the device for any reason. There are no user serviceable parts inside.
  • Disconnect the device’s main power when left unused for long periods of time.
  • Never connect this device to a dimmer pack.
  • Do not attempt to operate this device if it has been damaged in any way.
  • Never operate this device with the cover removed.
  • Do not attempt to operate this device if the power cord has been frayed or broken.
  • Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
  • Disconnect from main power before making any type of connection.
  • Never block the ventilation holes. Always be sure to mount this device in an area that will allow proper ventilation. Allow about 6″ (15cm) between this device and a wall.
  • Always mount this unit in a safe and stable matter.
  • Please route your power cord out of the way of foot traffic. Power cords should be routed so they are not likely to be walked on, or pinched by items placed upon or against them.
  • Keep flammable materials away from this fixture!
  • The device should be serviced by qualified service personnel when:
    A. The power-supply cord or the plug has been damaged.
    B. Objects have fallen on, or liquid has been spilled into, the device.
    C. The device has been immersed in liquid.
    D. The appliance does not appear to operate normally or exhibits a marked change in performance.

OVERVIEW

ELATION 170IP Pixel Driver User Guide - OVERVIEW

INSTALLATION GUIDELINES

FLAMMABLE MATERIAL WARNING! Keep drive a minimum of 5.0 feet (1.5m) away from flammable material and/or pyrotechnics.
DO NOT INSTALL THE DEVICE IF YOU ARE NOT QUALIFIED TO DO SO!

  • The driver MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.
  • Before installing or mounting any device, a professional equipment installer MUST be consulted to determine whether the mounting structure or surface is properly certified to safely support the combined weight of the device and any relevant accessories.
  • The device should be installed away from walking paths, seating areas, or any areas where unauthorized personnel may potentially reach the device by hand.

CONNECTIONS (DRIVERS IN SERIES)

  1. On Driver 1, connect the “DMX In” port to the DMX Controller using a 5-pin XLR cable.
    Connect the “LED Out” port to your LED Tape or Pixel Wash 40IPs using a 4-pin XLR cable.
  2. On Driver 1, connect the “DMX Thru” port to the “DMX In” port of the next driver in the series (Driver 2 in the illustration below) using a 5-pin XLR cable. This applies only if multiple drivers are being controlled by the DMX Controller.
  3. On Driver 2, connect the “LED Out” port to your LED Tape or Pixel Wash 40IPs using a 4-pin XLR cable.
  4. If Driver 2 is the last driver in your series, then the “DMX Thru” port can be left disconnected, as shown in the illustration below. Alternately, if there are additional drivers in your series, the “DMX Thru” port of Driver 2 should be connected to the “DMX In” port of the next driver.
  5. Once all connections have been made, connect the “Power In” port of each driver to a suitable power source.

ELATION 170IP Pixel Driver User Guide - CONNECTIONS

CONNECTIONS (DRIVERS IN PARALLEL)
Alternately, if your DMX controller features multiple outlet ports, you can also opt to set up the drivers in parallel, with each driver receiving its own dedicated outlet on the DMX controller and no direct link between the individual drivers. Such a setup can be particularly useful for running LED Tape strips, which can require a very large number of control channels to operate.

  1. On Driver 1, connect the “DMX In” port to the first outlet of the DMX Controller using a 5-pin XLR cable.
  2. On Driver 1, connect the “LED Out” port to your LED Tape or Pixel Wash 40IPs using a 4-pin XLR cable.
  3. Leave the “DMX Thru” port unconnected.
  4. Repeat steps 1-3 for each additional driver in your system. Once all connections have been made, connect the “Power In” port of each driver to a suitable power source.

ELATION 170IP Pixel Driver User Guide - CONNECTIONS (DRIVERS IN PARALLEL)

HI POWER MODE
This driver features a Hi Power Mode, which can be disabled in order to allow the driver to control additional Pixel Wash 40IP fixtures. The max number of fixtures that can be controlled by the driver is as follows:

  • Hi Power Mode ON: 5 fixtures max per driver
  • Hi Power Mode OFF: 8 fixtures max per driver

Please note that these limitations apply only when using the driver to operate Pixel Wash 40IP fixtures. Refer to the images below.

ELATION 170IP Pixel Driver User Guide - HI POWER MODE

PIXEL AMP 200
The Pixel Amp 200 device can be used to increase the number of Pixel Wash 40IP fixtures that can be controlled with a single driver.

  1. Link the fixtures in groups, where the maximum size of each group is 5 fixtures per group when Hi Power Mode is on, or 8 fixtures per group when Hi Power mode is off.
  2. Link the outlet port of the driver to the inlet of the first fixture of the first group.
  3. Link the outlet of the last unit in the first group to the inlet of the Pixel Amp 200.
  4. Link the outlet of the Pixel Amp 200 to the inlet of the first unit in the following group. 5. Repeat steps 3 and 4 until all the fixture groups are linked.

Please note that each driver can only accommodate a maximum of 5 fixture groups, regardless of whether Hi Power Mode in on or off. This translates to a maximum of 25 fixtures per driver with Hi Power Mode on (as shown below), or 40 fixtures per driver with Hi Power Mode Off. Multiple drivers can still be linked via the DMX Thru ports.

ELATION 170IP Pixel Driver User Guide - PIXEL AMP 200

MAXIMUM ALLOWABLE CABLE LENGTHS FOR PIXEL WASH 40IP
Without Pixel AMP 200 (max 8 Pixel Wash 40IP units): Pixel BCx cable* may be used to link multiple devices. Maximum allowable cable lengths are listed below.

  • Max length of cable connecting a Pixel Driver 170IP and a fixture: 98feet (30m)
  • Max length of cable connecting two fixtures: 98 feet (30m)
  • Max total cable length in a single chain: 98 feet (30m) including the lengths of the Pixel Wash 40IP(s)

ELATION 170IP Pixel Driver User Guide - MAXIMUM ALLOWABLE CABLE LENGTHS FOR PIXEL WASH 40IP

With up to 4pcs Pixel AMP 200:
Pixel BCx cable* may be used to link multiple devices. Maximum allowable cable lengths are listed below.

  • Max total cable length in a single chain: 360 feet (110m) including the lengths of the Pixel Wash 40IP(s)
  • Max distance from Pixel Driver 170IP to last fixture in a group: 98 ft (30m) including lengths of Pixel Driver 40IPs
  • Max distance from Pixel Amp 200 to last fixture in a group: 65 ft (20m) including lengths of Pixel Driver 40IPs

ELATION 170IP Pixel Driver User Guide - With up to 4pcs Pixel AMP 200

*For the Pixel BCx cable, the “x” represents the length of the cable in feet. Available lengths include 2′, 3′, 5′, 10′, 12′, 15′, 20′, 25′, 30′, and 50′.

WALL MOUNTING
The driver includes mounting flanges for wall mount installations. Use four (4) M6x25 selftapping screws and insert them through the mounting holes located on the flanges. Make sure that the driver is mounted firmly and securely before proceeding to use.

ELATION 170IP Pixel Driver User Guide - WALL MOUNTING

CLAMP MOUNTING
This device features an integrated mounting plate on the back side, which includes two holes for the installation of an Omega bracket. Insert the Omega bracket’s twist lock fasteners into the designated holes in the mounting plate, then twist the fasteners to secure the Omega bracket in place. Refer to the images below.

ELATION 170IP Pixel Driver User Guide - CLAMP MOUNTING

REMOTE CONTROL OPERATION

The Elation UC-IR24 infrared remote gives the user control of various functions for a variety of Elation fixtures with IR capabilities. Please note that the remote should be aimed at the front of the fixture, and that maximum operating range is 30 feet.
CONTROLS

  • ON and OFF buttons: When the ON button is pressed, the lighting fixture switches on and returns to its last running state. When the OFF button is pressed, the unit powers off.
  • STROBE: The unit shall strobe according to the selected color or program. The strobe rate can be adjusted by repeatedly pressing the + / – buttons, or 15 preset strobe speeds can directly be accessed by pressing buttons 1-15, where 1 is the slowest and 15 is the fastest.
  • SOUND: The unit shall trigger the last selected program steps based on the primary units microphone. The microphone sensitivity can then be adjusted with the +/- buttons.
  • COLOR: Select preset static colors using buttons 0-15. The intensity for the set color can then be adjusted with the +/- buttons.
  • PROGRAM: Internal programs can be selected by pressing buttons 0-13 (Note: since this unit only supports 13 programs, the 14 button and 15 button have no defined function for this unit). The selected program run speed can be adjusted with the+/- buttons.
  • + and – buttons: These buttons are used to adjust strobe rate when the STROBE button is active, mic sensitivity when the SOUND button is active, brightness intensity when the COLOR button is active, or program run speed when the PROGRAM button is active. The +/- buttons can be repeatedly pressed adjust the setting by single increments, or pressed and held to quickly make large adjustments.
  • 0-15 buttons: These buttons are used to select preset strobe speeds when the STROBE button is active, static colors when the COLOR button is active, or internal programs when the PROGRAM button is active. Colors stored in buttons 0-15 can be edited from the units menu if desired by the user.

ELATION 170IP Pixel Driver User Guide - REMOTE CONTROL OPERATION

CONTROL PANEL

The Pixel Driver 170IP features a display screen with a 4-button control pad, which can be used to easily adjust any device settings. Pressing the MODE button will cycle through the various Main Menu options. When the desired Main Menu option is displayed on the screen, press the SETUP button to enter the sub-menu, then use the UP and DOWN buttons to scroll through sub-menu options. In some cases, there will be a second sub-menu that can be navigated in the same way.

ELATION 170IP Pixel Driver User Guide - CONTROL PANEL

SYSTEM MENU

ELATION 170IP Pixel Driver User Guide - SYSTEM MENU

DMX TRAITS

ELATION 170IP Pixel Driver User Guide - DMX TRAITS

Note:

  • In LED Tape mode, the DMX channel control will vary depending on the set pixel count. 3 RGB control channels will be added for each additional pixel. Up to 170 pixels (510 DMX channels) can be controlled with each Pixel Driver 170IP device.
  • In Pixel Wash 40IP mode, the DMX channel control will vary depending on the set pixel count. 4 RGBW control channels will be added for each additional pixel. Up to 40 pixels (160 DMX channels) can be controlled with each Pixel Driver 170IP device.

PIXEL GROUPS

The number of pixels that this device can control is limited by the available number of DMX control channels. The device has a total of 512 available DMX control channels, and each pixel requires three channels (red, green, and blue) to operate. Therefore, the maximum number of pixels that can be controlled in standard configuration is 170: 170 pixels x 3 channels per pixel = 510 channels. This is the maximum number of 3-channel groups that can be accommodated without exceeding the 512 channel limitation.

However, this device also gives the user the ability to adjust the pixel grouping configuration. In the standard configuration, individual pixels are controlled independently for finer control over the resolution of the lighting display. Alternately, multiple individual pixels may be grouped together under a common set of control channels in order to reduce the number of required control channels. This also reduces the effective pixel count for each fixture. The downside to this is the reduced resolution of the lighting display.

In each pixel control mode, the first number denotes the number of individual pixels that make up each control group, while the second number denotes the number of control groups. Each control group will always occupy 3 DMX channels (for red, green, and blue control). This means that within each control group, all pixels will be controlled by the same set of 3 DMX channels.
For example, let us examine a 30-pixel strip, as shown below. Selecting 2×15 mode means that the pixels will be divided into 15 control groups, with each group containing 2 LEDs.

ELATION 170IP Pixel Driver User Guide - PIXEL GROUPS

ELATION 170IP Pixel Driver User Guide - PIXEL GROUPS ELATION 170IP Pixel Driver User Guide - PIXEL GROUPS ELATION 170IP Pixel Driver User Guide - PIXEL GROUPS

COLOR MACROS

ELATION 170IP Pixel Driver User Guide - COLOR MACROS

MAINTENANCE GUIDELINES

⚠ DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
MAINTENANCE Regular inspections are recommended to ensure proper function and extended life. There are no user serviceable parts inside this device. Please refer all other service issues to an authorized Elation service technician. Should you need any spare parts, please order genuine parts from your local Elation dealer. Please refer to the following points during routine inspections:
A. A detailed electrical check by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating.
B. Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during normal operation, resulting in damage or injury as larger parts could fall.
C. Check for any deformations on the housing, rigging hardware, and rigging points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the fixture. Damaged rigging points or unsecured rigging could cause the device to fall and seriously injure a person(s).
D. Electric power supply cables must not show any damage, material fatigue, or sediments. NEVER remove the ground prong from the power cable. TORQUE SETTINGS FOR SCREWS Following any repair or maintenance procedure in which the device’s cover has been removed or opened, the cover screws must be tightened with a torque driver in order to maintain the stated IP rating. All cover screws should be torqued to 11.3 lb-in (13.0 kg-cm).

TORQUE DRIVERS (Recommended): UTICA TS-30 (Shown) TORQUE DRIVER (Alternate):

  • Proto J6107A
  • Wiha 28887

ELATION 170IP Pixel Driver User Guide - TORQUE SETTINGS FOR SCREWS

⚠ CAUTION! DO NOT OVER TORQUE SCREWS AS THIS CAN CAUSE LEAKAGE ISSUES!

SPECIFICATIONS

CONTROL / CONNECTIONS
4-Button OLED Display
1 DMX Universe (170 Pixels)
LED Control: LED Tape or Pixel Wash 40IP
UC-IR24EL Remote (Included)
DMX Input via 5pin XLR Connector
DMX Output via 5pin XLR Connector
LED Out via 4pin XLR Connector
Hi Power Mode Off:
• control up to 8pcs Pixel Wash 40IP with the driver alone
• control up to 40pcs Pixel Wash 40IP with the use of 4pcs Pixel Amp 200 Hi Power Mode On:
• control up to 5pcs Pixel Wash 40IP with the driver alone
• control up to 25pcs Pixel Wash 40IP with the use of 4pcs Pixel Amp 200

SIZE / WEIGHT
Length: 3.68” (93.5mm)
Width: 7.38” (187.5mm)
Height (No Omega Bracket: 3” (75.7mm)
Height (With Omega Bracket: 4.4” (111.0mm)
Weight: 2.64 lbs. (1.2kgs.)

ELECTRICAL
DC Input 12-24VDC, 8.4A (Requires separate power supply)
200W Max Power Consumption

INCLUDED ACCESSORIES:
EL-IR Remote
IR Receiver Cable
2-pin Power Cable to adapt to PSU

APPROVALS / RATING
CE | RoHs | cETL | FCC IP65

ELATION 170IP Pixel Driver User Guide - APPROVALS

*Specifications are subject to change without notice.

DIMENSIONAL DRAWINGS

Dimension drawings not to scale

ELATION 170IP Pixel Driver User Guide - DIMENSIONAL DRAWINGS

OPTIONAL ACCESSORIES

ELATION 170IP Pixel Driver User Guide - OPTIONAL ACCESSORIES

SOFTWARE UPDATES

NOTICE: Before beginning the software update procedure, please contact Elation service for information, directions, and guidance. DO NOT proceed without contacting Elation service first!

  1. Copy the software update file to a Micro SD card.
  2. Insert the Micro SD card into the Uploader.
  3. Power on the Uploader and wait until the LCD displays “HUAYAO Software Update Box”.
    Use UP and DOWN buttons to scroll to “Output Type”, then press ENTER to confirm. Use UP and DOWN buttons to select “DMX”, then press ENTER button again to confirm.
  4. Use UP and DOWN buttons to select “Devices Upgrade”, then press ENTER button to confirm. Use UP and DOWN button to select the software update file which you want to upload to the Pixel Driver 170IP. Press the ENTER button again. The upload interface should now be displayed.
  5. Power on the Pixel Driver 170IP and set it to DMX mode. Use a 5 pin DMX cable to connect the Pixel Driver 170IP to the Uploader.
  6. Press the ENTER button. The Uploader will begin to upload the new software to the Pixel Driver 170IP. After the upload has been completed, press EXIT button to exit the uploader interface.
  7. Power off and then restart Pixel Driver 170IP. 8. Check if Pixel Driver 170IP has been updated to the new software by checking the software version listed in the system menu. If the update was not successful, please repeat the process.

FCC STATEMENT

Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

ELATION 170IP Pixel Driver User Guide - FCC icon

Documents / Resources

PDF thumbnail170IP Pixel Driver
User Guide · 170IP Pixel Driver, 170IP, Pixel Driver, Driver

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.