EIKI LC-VC1 Multimedia Projector Owner's Manual

TO THE OWNER
Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.
WARNING:
SAFETY PRECAUTIONS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This projector produces intense light from the projection lens. Do not stare directly into the lens as possible.
Eye damage could result. Be especially careful that children do not stare directly into the beam.
This projector should be set in the way indicated. If not, it may result in a fire hazard.

Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. Minimum distance should be taken. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.
Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR SACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT OANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER’S MANUAL WITH THIS UNIT.

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.
Do not expose this unit to rain or use near water… for example, in a wet basement, near a swimming pool, etc…
Do not use attachments not recommended by the manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer’s instructions, and should use a mounting kit approved by the manufacturers.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided. Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.
Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been damaged.
f. When the projector exhibits a distinct change in performance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

COMPLIANCES
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature.
Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIOPMENT AND EASILY ACCESSIBLE.

TRADEMARKS

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

Windows and PowerPoint are registered trademarks of Microsoft Corporation.
Each name of corporations or products in the owner’s manual is a trademark or a registered trademark of its respective corporation.

FEATURES AND DESIGN

This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use.
The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technoloav.

Compatibility
This projector widely accepts various video and computer input signals including;
• 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PALN color system can be connected.
• Component Video
Component video signals, such as a DVD player output high definition TV signals including 480i, 4BOp, 575i, 575p, 720p, 1 035i, 1 080i-50 or 1 080i- 60, can be connected.
• S-Video
S-Video signals, such as a S-VHS VCR output signals, can be connected.
• Computers
IBM-compatible and Macintosh computers up to 1280 x 1024 resolution.

High Resolution Image
This projector provides 1366 x 768 dots resolution for computer input and 800 horizontal TV lines. The resolution from computer between XGA (1024 x 768) and SXGA (1280 x 1024) is compressed into 1024 x 768 dots. This projector cannot display image of over 1280 x 1024 dots. When the resolution of your computer is over than 1280 x 1024, reset computer output for lower resolution.
Multi-Scan System
This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for complicated manual adjustment of frequency and other settings.

One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and the best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise.
Progressive Scan (for Video)
Progressive Scan function converts interlace video signals into progressive scan signals and provide fine picture quality.

Digital Zoom (for Computer)
Digital Zoom function magnifies the image up to 16 times, allowing you to focus on crucial information at a presentation.
Motor-driven Lens Shift
Projection Lens can be moved up and down with Motordriven Lens Shift function. This function makes it easy to provide projected image where you want. Zoom and Focus can be also adjusted with Motor-driven operation.

Keystone Correction
Positioning height of projector may result in distorted images being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally altering projection to produce undistorted images.
Power Manaqement
Power Management function is provided to reduce power consumption while the projector is not in use. This Power Management function operates to turn Projection Lamp off when the projector detects signal interruption and any button is not pressed over 5 minutes. Projection Lamp is automatically turned on again when the projector detects the signal or any operation button is pressed. This projector is shipped with this function ON.

Multilanguage Menu Display
Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish or Japanese.

NAME OF EACH PART OF PROJECTOR

PREPARATION CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V or 200240 V AC. The projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power supply being in use. Connect projector with the peripheral equipment before turning projector on. (Refer to pages 11 — 13 for connection.)

CAUTION
For safety, unplug the AC Power Cord when the appliance is not used.
The AC outlet must be near this equipment and must be easily accessible.

NOTE ON THE POWER CORD The AC Power Cord must meet the requirement of the country where you use the projector. Confirm the AC plug type with the chart below. The proper AC power cord must be used. If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
Projector side	AC Outlet side
	For the U.S.A. and Canada	For Continental Europe

ADJUSTABLE FEET
POSITIONING THE PROJECTOR
This projector is designed to project on a flat projection surface and it can be focused from 4.43’ (1 .35m) 45.9’ (14.Om). Refer to the figure below to adjust the screen size.
RECOMMENDATION

Screen Size	40″	100″	200″	300″	400″
Width x Height	886 x 498 mm	2215 x 1245 mm	4430 x 2490 mm	6644 x 3736 mm	8860 x 4980 mm

Brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide the best image.
LENS SHIFT ADJUSTMENT

Projection Lens can be moved up and down with Motordriven Lens Shift function.
This function makes it easy to provide the projected image where you want. Refer to P 21 for operation

NOTE
Screen size and lens shift ratio on the above charts are standard values and they may change by positioning conditions.

ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by rotating Adjustable Feet. Projection angle can be adjusted to 9.0 degrees.

Lift the front of projector and pull Feet Lock Latches on both sides of projector.
Release Feet Lock Latches to lock Adjustable Feet and rotate Adjustable Feet to fine tune position and tilt.
To shorten Adjustable Feet, lift the front of projector and pull and undo Feet Lock Latches.

Position and keystone distortion of the image can be adjusted using Menu Operation. (Refer to P 21 and 36.)

MOVING PROJECTOR
Use Carry Handle when moving projector. When moving projector, replace Lens Cover and retract Adjustable Feet to prevent damage to Projection Lens and cabinet. When this projector is not in use for an extended period, put it into the case (Dust Cover) supplied with this projector.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

Do not bump projector, otherwise damages or malfunctions may result
When carrying projector, use a suitable carrying case

Do not transport projector by using a courier or transport service in an unsuitable transport case. This may cause damage to projector.

To transport projector through a courier or transport service, consult your dealer for best way.

TERMINALS OF PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Cables used for connection (* = Cables are not supplied with this projector.)

Video Cable (RCA x 1)
Video Cable (RCA x 3)*, (BNC x 1 )*, (BNC x 2)* or (BNC x 3)*

S-VIDEO Cable
Audio Cable (RCA x 2)
Speaker Cable (Mini x 1 (stereo)) *

NOTE :
When connecting projector, AC Power Cords of both projector and external equipment should be disconnected from AC outlet.

CONNECTING TO COMPUTER

Cables used for connection (* = Cables are not supplied with this projector.)

VGA Cable (HDB 15 pin) *
Video Cable (BNC x 5) *

MAC Adapter (in the case of connecting Macintosh computer) *
Audio Cables (RCA x 2) or (RCA x 1 – Mini Plug (mono)) *
Speaker Cable (Mini Plug (stereo)) *

NOTE :
When connecting the cable, AC Power Cords of both projector and externa! equipment should be disconnected from AC outlet. Tum projector and peripheral equipment on before your computer is switched on.

TOP CONTROLS AND INDICATORS

This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.

TOP CONTROL

OPERATION AND REMOTE CONTROL

Remote Control Unit can be used as either Wired or Wireless.

OPERATING RANGE
Point Remote Control toward projector (Remote Receiver) whenever pressing the buttons. Maximum operating range for Remote Control is about 16.4’ (Sm) and 60° in front and rear of projector.

WIRED REMOTE CONTROL OPERATIONS
When using this Remote Control Unit as Wired Remote Control, Connect Remote Control Unit to R/C JACK with Remote Control Cable (supplied). Batteries installation is required when using as Wired Remote Control Unit.

REMOTE CONTROL BATTERIES INSTALLATION

Remove the battery compartment lid
Slide 2 batteries into the compartment.
Replace the compartment lid.

To insure safe operation, please observe the following precautions:

Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at the same time.

Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose Remote Control Unit to moisture, or heat

Do not drop Remote Control Unit.
If batteries have leaked on Remote Control Unit, carefully wipe the case clean and load new batteries..

OPERATION ON-SCREEN MENU

HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through ON-SCREEN MENU. Refer to the following pages to operate each adjustment on ON-SCREEN MENU.

DISPLAY MENU Press MENU button to display ON-SCREEN MENU.
MOVING POINTER
Move the pointer (* see below) or adjust the value of item by pressing POINT button(s) on Top Control or on Remote Control Unit.* Pointer is the icon on ON-SCREEN MENU to select the item. See the figures on the section “FLOW OF ON-SCREEN MENU OPERATION” below.
SELECT ITEM
Select the item by pressing SELECT button.

FLOW OF ON-SCREEN MENU OPERATION

Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU BAR). A red frame is POINTER
Select item to be adjusted
Move POINTER (red frame) to MENU ICON that you want to select by pressing POINT RIGHT / LEFT buttons.

Control and adjust through ON-SCREEN MENU
Press POINT DOWN button and move POINTER (red frame or red arrow) to ITEM that you want to adjust, and then press SELECT button to show Item Data.
Adjust ITEM DATA by pressing POINT buttons.
Refer to the following pages for details of respective adjustments.

MENU BAR
FOR PC SOURCE Press MENU BUTTON for PC input source. FOR VIDEO SOURCE

TURNING ON/OFF PROJECTOR

TURNING ON PROJECTOR

Complete the peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to “CONNECTING TO PROJECTOR” on Pages 11~-13 for connecting that equipment.)
Connect the projector’s AC Power Cord into an AC outlet and turn MAIN ON I OFF SWITCH to ON. LAMP Indicator lights RED, and READY Indicator lights GREEN.
NOTE : When “On start” function is ON, this projector is turned on automatically by switching MAIN ON / OFF SWITCH on. (Refer to page 37.)

Press POWER ON-OFF button on Top Control or on Remote Control Unit to ON. LAMP Indicator dims, and Cooling Fans start to operate.
Preparation Display appears on a screen and the count-down starts. The signal from the PC or Video source appears after 30 seconds.

TURNING OFF THE PROJECTOR

Press POWER ON-OFF button on Top Control or on Remote Control Unit, and the message “Power off?” appears on a screen.

Press POWER ON-OFF button again to turn off projector. LAMP Indicator lights bright and READY Indicator turns off. After projector is turned off, Cooling Fans operate (for 90 seconds). During this “Cooling Down” period, this appliance cannot be turned on.
When projector has cooled down, READY Indicator turns to green again and you can turn projector on. After cooling down completely, turn MAIN ON / OFF SWITCH to OFF and disconnect AC Power Cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.
When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on page 37.
When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.
When WARNING TEMP. Indicator continues to flash, follow procedures below:

Turn MAIN ON / OFF SWITCH to OFF and disconnect the AC Power Cord from a AC outlet.
Check Air Filters for dust accumulation.
Clean Air Filters. (See “AIR FILTER CARE AND CLEANING” section on page 38.)

Turn projector on again.

If WARNING TEMP. Indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center.

ADJUSTING SCREEN

ZOOM ADJUSTMENT

Press ZOOM A/V button(s) on Top Control or on Remote Control Unit. The message “Zoom” is displayed.
Press ZOOM A button or POINT UP button to make image larger, and press ZOOM V button or POINT DOWN button to make image smaller.

FOCUS ADJUSTMENT

Press FOCUS A/V button(s) on Top Control or on Remote Control Unit. The message “Focus” is displayed.
Adjust focus of the image by pressing FOCUS A/V button(s) or POINT UP/DOWN button(s).

LENS SHIFT ADJUSTMENT

Press LENS SHIFT A/V button(s) on Top Control or LENS SHIFT button on Remote Control Unit. The message “Lens shift” is displayed.
Press LENS SHIFT A button or POINT UP button to move image up, and press LENS SHIFT V button or POINT DOWN button to move image down. Refer to P9 for operating range.

KEYSTONE ADJUSTMENT
If image has keystone distortion, correct image with KEYSTONE adjustment

Press KEYSTONE button on Remote Control Unit or select Keystone on SETTING Menu (P36). The message “Keystone” is displayed.
Correct keystone distortion by pressing POINT UP/DOWN button(s). PressPOINT UP button to reduce upper part of the image, and press POINT DOWN button to reduce lower part of the image. To reset Keystone adjustment, press NORMAL button.

NO SHOW FUNCTION
Press NO SHOW button on Remote Control Unit to black out the image. To restore to normal, press NO SHOW button again or press any other button.

PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze the picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button.
Press VOLUME (+1—) button(s) on Top Control or on Remote Control Unit to adjust volume. Volume dialog box appears on the screen for a few seconds.
(+) button to increase volume, and (—) button decreasing.
MUTE SETTING
Press MUTE button on Remote Control Unit to cut off sound. To restore sound to its previous level, press MUTE button again or press Volume (+/—) button(s).

SELECTING INPUT SOURCE

DIRECT OPERATION
Choose either Input 1 or Input 2 by pressing INPUT button on Top Control or on Remote Control Unit.

MENU OPERATION

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon.
Press POINT DOWN button to move a red arrow pointer to either Input 1 or Input 2 that you want to choose and then press SELECT button. When choosing Input 2, Source Select Menu will appear. Move POINTER to RGBand then press SELECT button. (Input 2 accepts R, G, B, HN and V computer signals (P 13).)

This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to “COMPATIBLE COMPUTER SPECIFICATION” on page 27). When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)
Note: Proiector may display one of the foIIowin~ messanes.
When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment

SELECTING COMPUTER SYSTEM

function operates to adjust projector and the message “AUTO PC Adj.” is displayed on SYSTEM icon. When image is not provided properly, manual adjustment is required. (Refer to P25 and 26.)
There is no signal input from computer. Make sure the connection of computer and projector is set correctly. (Refer to TROUBLESHOOTING on page 40.)
AUTO PC Adj.
When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and the message “AUTO PC Adj.” Is displayed on SYSTEM icon. When image is not provided properly, manual adjustment is required (Refer to P25 and 26).
No signal
There is no signal input from computer. Make sure the connection of computer and projector is set correctly, (Refer to TROUBLESHOOTING on page 40.)

SELECT COMPUTER SYSTEM MANUALLY
This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SYSTEM icon.

Press POINT DOWN button to move a red arrow pointer to the system that you want to set, and then press SELECT button. Auto PC Adjustment function is provided to automatically adjust Fine sync., Total dots, and Picture Position to conform to your computer. Auto PC Adjustment function can be operated as follows.

PC ADJUSTMENT

AUTO PC ADJUSTMENT
Auto PC Adj.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon.

Press POINT DOWN button to move a red frame pointer to AUTO PC Adj. icon and then press SELECT button. This Auto PC Adjustment can be executed by pressing AUTO PC ADJ. button on Top Control or on Remote Control Unit.
Fine sync, Total dots and Picture Position of some computers may not be fully adjusted with Auto PC Adjustment function. When the image is not provided properly through this function, manual adjustment is required. (Refer to page 25, 26.)

Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode in SYSTEM Menu (above). Refer to step 3 of MANUAL PC ADJUSTMENT section (P26).
NOTE: Auto PC Adjustment function cannot be operated when “RGB,” “HDTV72Op,” “HDTV1O35i” or “HDTV1O8Oi” is selected on SYSTEM Menu (P23, 24).

MANUAL PC ADJUSTMENT
This projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-Scan system of this projector. If this happens, projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it.
Note : This PC ADJUST Menu cannot be operated when “RGB” is selected on SYSTEM Menu (P23, 24).

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon.
Press POINT DOWN button to move a red frame pointer to the item that you want to adjust and then press SELECT button. Adjustment dialog box will appear. Press POINT LEFT/RIGHT button to adjust the value.

Adjust the picture as necessary to eliminate flicker from the display.
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 255.)

The number of total dots in one horizontal period. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image.

Adjust horizontal picture position. Press POINT LEFT/RIGHT button(s) to adjust the position.

Adjust vertical picture position. Press POINT LEFT/RIGHT button(s) o adjust the position.

Press SELECT button to show the information of computer selected.

The number of the total horizontal lines. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image.

Adjusts clamp level. When the image has a dark bar(s), try this adjustment.
Selects area displayed with this projector. Select the resolution at the Display area dialog box.

Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) and adjust number to match the resolution ofimage.

Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) and adjust number to match the resolution of image.
Adjustment of width of image. Press POINT LEFT/RIGHT button(s) for adjustments.

Adjustment of height of image. Press POINT LEFT/RIGHT button(s) for adjustments.
NOTE: Display area (H/V), Horizontal scale and Vertical scale cannot be adjusted when “HDTV1O35i” or “HDTV1O8Oi” is selected on SYSTEM Menu (P23, 24).
Fine sync and Total dots cannot be fully adjusted when ‘HDTV1O35i” or “HDTV1O8Oi” is selected on SYSTEM Menu (P23, 24).
To store adjustment parameters, move a red frame pointer to Stored icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store to and then press SELECT button.

I o clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then SELECT button. Move a red arrow pointer to the Mode that you want to clear and then press SELECT button.
Other icons operates as follows.

Reset all adjust parameters on adjustment dialog box to previous figure.

Closes PC ADJUST MENU

COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and less than 180 MHz of Dot Clock.
NOTE : Specifications are subject to change without notice.

ON-SCREEN DISPLAY	RESOLUTION	H-Freq. (khz)	V-Freq. (khz)
VGA 1	640 x 480	31.47	59.88
VGA 2	720 x 400	31.47	70.09
VGA 3	640 x 400	31.47	70.09
VGA 4	640 x 480	37.86	74.38
VGA 5	640 x 480	37.86	72.81
VGA 6	640 x 480	37.50	75.00
VGA 7	640 x 480	43.269	85.00
MAC LC13	640 x 480	34.97	66.60
MAC 13	640 x 480	35.00	66.67
RGB	—	15.625	50 (interface)
RGB	—	15.734	60 (interface)
SVGA 1	800 x 600	35.156	56.25
SVGA 2	800 x 600	37.88	60.32
SVGA 3	800 x 600	46.875	75.00
SVGA 4	800 x 600	53.674	85.06
SVGA 5	800 x 600	48.08	72.19
SVGA 6	800 x 600	37.90	61.03
SVGA 7	800 x 600	34.50	55.38
SVGA 8	800 x 600	38.00	60.51
SVGA 9	800 x 600	38.60	60.31
SVGA 10	832 x 624	32.70	51.09
SVGA 11	1024 x 768	38.00	60.51
MAC 16	1024 x 768	49.72	74.55
XGA 1	1024 x 768	48.36	60.00
XGA 2	1024 x 768	68.677	84.997
XGA 3	1024 x 768	60.023	75.03
XGA 4	1024 x 768	56.47	70.07
XGA 5	1024 x 768	60.31	74.92
XGA 6	1024 x 768	48.50	60.02
XGA 7	1024 x 768	44.00	54.58
XGA 8	1024 x 768	63.48	79.35
XGA 9	1024 x 768	36.00	87.17(interface)
XGA 10	1024 x 768	36.04	77.07
XGA 11	1024 x 768	61.00	75.70
XGA 12	1024 x 768	35.522	86.96 (interface)
XGA 13	1024 x 768	46.90	58.20
XGA 14	1024 x 768	47.00	58.30
XGA15	1024 x 768	58.03	72.0
MAC 19	1024 x 768	60.24	75.08
MAC 21	1152 x 870	68.68	75.06
SXGA 1	1152 x 864	64.20	70.40
SXGA 2	1280 x 1024	62.50	58.60
SXGA 3	1280 x 1024	63.90	60.00
SXGA 4	1280 x 1024	63.34	59.98
SXGA 5	1280 x 1024	63.74	60.01
SXGA 6	1280 x 1024	71.69	67.19
SXGA 7	1280 x 1024	81.13	76.107
SXGA 8	1280 x 1024	63.98	60.02
SXGA 9	1280 x 1024	79.976	75.025
SXGA 10	1280 x 960	60.00	60.00
SXGA 11	1152 x 900	61.20	65.20
SXGA 12	1152 x 900	71.40	75.60
SXGA 13	1280 x 1024	50.00	86.00 (interface)
SXGA 14	1280 x 1024	50.00	94.00 (interface)
SXGA 15	1280 x 1024	63.37	60.01
SXGA 16	1280 x 1024	76.97	72.00
SXGA 17	1152 x 900	61.85	66.00
SXGA 18	1280 x 1024	46.43	86.70 (interface)
SXGA 19	1280 x 1024	63.79	60.18
SXGA 20	1280 x 1024	91.146	85.024
MAC	1280 x 960	75.00	75.08
MAC	1280 x 1024	80.00	75.08
HDTV720p	—	45.00	60.00
HDTV1035i	—	33.75	60.00 (interface)
HDTV 1080i	—	33.75	60.00 (interface)

NOTE: Specifications are subject to change without notice.

PICTURE IMAGE ADJUSTMENTS

IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on the Remote Control Unit.

Normal picture level preset on this projector. This normal picture level can also be selected by pressing NORMAL button.

Picture level adjusted for the picture with fine tone.

User preset picture adjustment in IMA(.iE AL)JUS I Menu (t~29).IMAGE LEVEL SELECT (MENU)

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon.
Press POINT DOWN button to move a red frame pointer to the level that you want to set and then press SELECT button.
+
Normal picture level preset on this projector.

Picture level adjusted for the picture with fine tone.

User preset picture adjustment in IMAGE ADJUST Menu (P29).

IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to IMAGE ADJUST Menu icon.
2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust. and then press SELECT button. The level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s).

Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)

Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)

To store manually preset image, move a red frame pointer to STORE icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to the Image 1 to 4 where you want to set and then press SELECT button

PICTURE SCREEN ADJUSTMENT

This projector has a picture screen resize function, which enables you to display the desirable image size.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SCREEN Menu icon.
Press POINT DOWN button and move a red frame pointer to the function that you want to select and then press SELECT button.

Provides image to fit the vertical size of the screen.

Provides image to fit the horizontal size of the screen.

Provides image in its original size. When the original image size is larger than screen size (1366 x 768), this projector enters Digital Zoom mode automatically. Image size can be set to Normal by pressing NORMAL button.

Adjusts image size or pans image. In “Digital Zoom” mode, the ON- SCREEN MENU disappears and the magnifying glass icon and the message “D. Zoom” is displayed.
This projector also enters Digital Zoom mode by pressing the D.ZOOM A/V button on Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press the D.ZOOM A button or the SELECT button. The image is magnified by degrees.
Compress function
To compress the image size, press the D.ZOOM V button. The
Panning function To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is larger than the screen size.
To return to screen size previously set, press NORMAL button.
To cancel Digital Zoom mode, press any button except D.ZOOM A/V, SELECT, POINT, NORMAL or AUTO PC ADJ. button.

NOTE
S This SCREEN Menu cannot be operated when “HDTV72Op,” “HDTV1O35i” or “HDTV1O8Oi” is selected on SYSTEM Menu (P23, 24).

True and Digital Zoom cannot be selected when “RGB” is selected on SYSTEM Menu (P23, 24).

This projector cannot display any resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting projector.
The image data in other than XGA (1024 x 768) is modified to fit the screen size in the initial mode.
Panning function may not operate properly if the computer system prepared on PC ADJUST Menu is used.