ecowitt WS6210 4G and Wi-Fi Weather Station Mobile Gateway User Manual

The WS6210 is a versatile wireless communication device suitable
for meteorological data collection and transmission via Wi-Fi and
4G connections. It supports various sensor data types.

FAQ (Frequently Asked Questions)

Q: How do I connect the WS6210 to my Wi-Fi network?

A: To connect to Wi-Fi, tap the AP button for 5 seconds to
enable the onboard Wi-Fi AP. Then, connect to the device using IP
address 192.168.4.1 and SSID WS6210x-WIFIxxxx.

Q: What is the purpose of the touch buttons on the WS6210?

A: The touch buttons (Reset and AP) are used for unlocking the
device, initiating sensor learning mode, and managing Wi-Fi access
point functionality.

“`

View Fullscreen

4G & Wi-Fi Weather Station Mobile Gateway
Model: WS6210
https://s.ecowitt.com/D33XUA

Content
1.Package ……………………………………………………………………………………… 1 2. Construction & Layout ……………………………………………………………….. 2
2.1 Multiple Views and Size …………………………………………………….. 2 2.2 Layout ……………………………………………………………………………… 3 2.3 Light Indicators …………………………………………………………………. 5 2.4 Touch Button ……………………………………………………………………..6 3. Brief Introduction ………………………………………………………………………..7 4. First Use ………………………………………………………………………………….. 10 4.1 Power on ………………………………………………………………………… 10 4.2 Install the APP ………………………………………………………………….11 4.3 Working Mode ………………………………………………………………… 12 4.4 How to delete and reset WS6210 ………………………………………..23 5. General Setting and Checkup ………………………………………………………23 6. Sensor start up …………………………………………………………………………..27 7. Mounting ………………………………………………………………………………….28 7.1 Solar Panel Size ………………………………………………………………. 28 7.2 Mounting …………………………………………………………………………28 8. Web UI On WS6210 …………………………………………………………………. 31 8.1 Local Network ………………………………………………………………… 31 8.2 Weather Services ………………………………………………………………32 8.3 Device Setting …………………………………………………………………. 33

8.4 Unit Settings …………………………………………………………………….35 8.5 Calibration ……………………………………………………………………….36 8.6 Rain Totals ……………………………………………………………………… 39 8.7 Sensors ID ……………………………………………………………………….42 8.8 Live Data …………………………………………………………………………45 8.9 Modem Management ……………………………………………………….. 46 8.10 SD Card Management ……………………………………………………..53 8.11 Firmware updates …………………………………………………………… 55 9. Product Features ………………………………………………………………………..56 10. Specifications ………………………………………………………………………….56 11. Miscellaneous ………………………………………………………………………….59 11.1 Replacing the SD/SIM Card ……………………………………………..59 11.2 Manually Adding …………………………………………………………….60 11.3 SIM Card Renewal ………………………………………………………….62 12. Optional Sensors …………………………………………………………………….. 64 12.1 Sensor Data Reception Priority …………………………………………64 12.2 Sensors …………………………………………………………………………. 64 12.3 IoT Device ……………………………………………………………………..67 13. Warranty …………………………………………………………………………………68 14. FCC ………………………………………………………………………………………. 69 15. Care and Maintenance ………………………………………………………………71 16. Contact Us ………………………………………………………………………………72

16.1 After-sales Service …………………………………………………………. 72 16.2 Stay in Touch ………………………………………………………………… 72

1.Package

The following items comprise the WS6210 and its accessories.

QTY
1

Item
WS6210 (4G & Wi-Fi Weather Station Mobile Gateway)

Hose Clamp

(3 * Fits pipe diameter: 46-70mm & 3 * Fits pipe diameter: 21-38mm. Choose according to the need)

Hose Clamp Brackets

M5*8 Screws

SD13 to USB power cable, length 50cm(19.7 inch)

Solar panel with cable, length 70cm(27.6 inch)

Galvanized Bracket for solar panel

Screws for solar panel

User Manual

Quick Start

Table 1 Central WS6210 unit and accessories

QTY
8 1 1

Item
AA rechargeable NiMH batteries Nano-SIM card Micro SD card 8G

Table 2 Accessories list (included)

2. Construction & Layout
2.1 Multiple Views and Size 1. WS6210 Size
Figure 1
2

2.2 Layout

Inside

Outside 2G/4G Antenna Unable to open Pressure Balance Valve Power Port Left turn to unlock, right turn to lock Power Switch Press to power on/off
Table 3
4

2.3 Light Indicators

Light Unlock

Indicators
Off: Locked key operation is prohibited On: Unlocked key operation is possible.

RF Wi-Fi
4G

Flashes regularly: Sensor Learning Blinking Once: A successful reception of sensor signal.
Continuous blinking: AP on. Off: Wi-Fi de-activated. Fast blinking: In Wi-Fi provisioning mode Slow blinking: Wi-Fi connected without internet Steady on: Wi-Fi connected with internet access
Off: Module is not recognized Flashes quickly: The module is under-recognizing Blinks slowly: When registering with the network Flashes once every 5 seconds: Successful network connection

Table 4

2.4 Touch Button The device has two touch buttons Reset and AP.
Tap Reset & AP Button alternatively four times (tap interval < 1.5s) to unlock the WS6210. The below button works when in the unlocked state.

Reset Button Press and hold the button for
3 seconds: it will turn on the receiver and will be in sensor learning mode. The RF LED will flash two times per second for 3 minutes until the learning process is completed.
10 seconds: The gateway reboots to factory default settings. The four LEDs flash two times per second three times, then the device will reboot.

AP Button
Hold for 5 seconds:
Turn on the onboard Wi-Fi AP for 5 minutes. The device can be connected via IP address 192.168.4.1and SSID WS6210x-WIFIxxxx.

Table 5 6

3. Brief Introduction
Thank you for purchasing the Ecowitt WS6210 weather station mobile receiver and transmitter. The WS6210 is a versatile wireless communication device supporting various wireless communication protocols. It is suitable for meteorological data collection and transmission. The product supports Wi-Fi and 4G connections for receiving and processing multiple sensor data types.
Figure 2 4G Scenario
Outdoor Use: The product can use 4G for data transmission when used outdoors without power supply from the grid and without WLAN connectivity. It can also be used outdoors via an available WLAN connection when permanent power supply via the electricity grid or other means (powerstation) is available.
7

Figure 3 WIFI + 4G Scenario
Indoor Use: When used indoors and WLAN connection is available, the product prioritizes Wi-Fi for data transmission. If Wi-Fi disconnects, it switches to 4G to maintain continuous data flow. (This is a configuration option, see chapter 4.3) The WS6210 is technically speaking a gateway, a display-less console, which needs to be used with optional sensors to obtain weather or other environment related data and is not a standalone product. The following user guide provides step-by-step instructions for installation and operation. Use this manual to become familiar with your weather station and save it for future reference.
8

General Terms Used in the Manual: Weather Station: Includes the console and sensors (or sensor array). Gateway: Also known as a hub, it is a Displayless console. Here, refer to the WS6210 device. Transmitter: Refers to the sensor. Receiver: Refers to the console. RF: Radio frequency. It refers to the ISM and SRD SUBG (Industrial, Scientific and Medical and Short Range Devices frequency bands below 1 GHz) for communicating between the gateway and its sensors. This frequency is not the same as the 4G modem or Wi-Fi working frequency. ISM/SRD bands are kept separate from 4G frequencies by national regulations to avoid interferences. Typical ISM/SRD frequencies are 915 (Americas), 868 (Europe), 433 (worldwide), 920 (Japan, Korea). 4G: A mobile data network standard (LTE): Long Term Evolution or 4th generation. WS6210 has a built-in 4G modem that can be configured to upload data via a 4G network. It needs a SIM card and the 4G service provider covers the area where you want the WS6210 to be installed.
9

4. First Use
4.1 Power on 1. Press the physical Power button to power it on. Four lights will turn on for 3s when powered on successfully. As illustrated below:
Figure 4
2. When first used, please charge the WS6210 using the included USB cable. The batteries will be fully charged in 10 hours.
Figure 5 Note: 1. You can also use an external charger, Do not use normal, non-rechargeable
10

batteries ! This could result in battery leakage and will damage the device 2. Reboot the device will need to unplug the USB cable, then press the physical Power button twice.
4.2 Install the APP
1Scan the QR code on the body of WS6210 to download the app. Assure you have the location and Wi-Fi service enabled for this Ecowitt APP.
Figure 6
2Run the “ecowitt” APP and register your account 3Open the APP, tap on “menu” “device” “+add a new device”- choose the model of ws6210 from the product listing
11

4.3 Working Mode

Figure 7

WS6210 has three working modes available for uploading the data to weather services, like www.ecowitt.net, weather underground, wow, weather cloud, and custom server is possible too.
1. Ecowitt SIM: The device comes with a SIM card pre-installed in the factory. You can use the SIM card to upload data. The default package includes a prepaid 90-day (300MB) service. If you want to use this for data uploading, please refer to section 4.3.1 for the activation. You may extend the cellular data service by going through the SIM card renewal process on the “ecowitt” app before the data service expires.
2. User SIM: Open the housing of WS6210, remove the pre-installed SIM card, and replace it with your SIM card. Please refer to section 4.3.2 for the setup.

3. Wi-Fi: If your location has Wi-Fi and USB power access, you may refer to section 4.3.3 for the setup.
Cellular Service and Wi-Fi can both be set at the same time. When both connections are present, the Wi-Fi connection has higher priority, and it will only switch using the SIM cellular connection when the Wi-Fi connection is unavailable. Select the mode that is appropriate for you.

4.3.1 Ecowitt SIM
Ensure the provided Ecowitt SIM card is compatible with the operating service provider in your country. If the built-in SIM card is not supported in your region, replace the SIM card with yours. Refers to Section 4.3.2

Country/Region

Operator

Country/Region

Operator

Albania

Vodafone

Malta

Vodafone

Australia

Vodafone

Mozambique

Vodafone

Austria

H3G

Myanmar

MPT

Brazil

Telefonica

Netherlands

Vodafone

Cambodia

Smart

New Zealand

OneNZ

Canada

Rogers

Philippines

Smart

China

ChinaMobile/Unico m

Portugal

Vodafone

CongoDR

Vodafone

Romania

Vodafone

Czech Republic Denmark
France
Germany Ghana Greece
Hong Kong, China
Hungary Indonesia
Ireland Israel Italy

Vodafone
H3G Bouygues Telecom/Orange Vodafone Vodafone Vodafone
H3G
Vodafone Indosat H3G/Vodafone Partner/Pelephone H3G/Vodafone

Japan

KDDI AU

Lesotho Macau, China

Vodafone H3G

Russian Federation
Saudi Arabia

MTS STC

Singapore

Starhub

South Africa South Korea
Spain

Vodafone SKTelecom Vodafone

Sweden

H3G

Taiwan, China

CHT/FET

Tanzania

Vodafone

Thailand

AIS/Truemove

Turkey

Vodafone-Telsim

UAE

Etisalat

United Kingdom

H3G/Vodafone

USA

AT&T/T-Mobile

Vitenam

Vitenam Mobile

Malaysia

Celcom/Mi3G-UMo bile

Table 6 Regions where the built-in SIM card service is supported
1. Tap on “menu” “device” “+add a new device”- choose the model of ws6210 from the product listing.
2. Tap on the button marked with “Ecowitt SIM Card.”

Figure 8
3. Scan the QR code on the device and bind it simultaneously.
15

Figure 9
4. Select the country or region for the SIM card usage. * Note: that it cannot be changed once activated
Figure 10
5. Reboot the WS6210, then wait approximately 30-60 minutes for the data to upload.
16

You can see the battery level on dashboard.
Figure 11
Note: If there is no data for more than 60 minutes, go to the 8.9 interface for detailed analysis.
4.3.2 User’s SIM Card 4.3.2.1. Replace the SlM Card
(Note: Please refer to section11.1 for specific operations)
Figure 12
4.3.2.2. Tap on the cell marked with “User SIM Card”
17

Figure 13
4.3.2.3. Fill out APN Settings and wait for the data to be uploaded. APN: Access Point Name, used for data communication and can be edited. Correct APN settings are necessary for proper use if using a custom SIM card. You can see the battery level on dashboard.
Figure 14 18

4.3.3 Wi-Fi Provisioning Note1: Using Wi-Fi for data uploading consumes much power and requires the
WS6210 console to be powered by connecting to a USB power socket
instead of a solar panel. Note2: Disabling your phone’s mobile data service will help avoid many
unknown problem during the registration of the gateway with your
network router. (As shown in the figure below)
Figure 15
4.3.3.1. Turn on the WS6210’s AP
Make sure WS6210 is unlocked. Holding the AP Button for 5 seconds will
turn on WS6210’s Wi-Fi AP for 5 minutes.
Figure 16 19

4.3.3.2. AP: access point.
The WS6210 has a built-in WiFi access point (SSID WS6210x-WIFInnnn) which can be used to access the device for configuration and data viewing (IP address 192.168.4.1).
It can also be used to connect the device to a local wireless network (WLAN) by providing the router login credentials (SSID, password) and via that to the internet. The connection to the local network once established will also be maintained when the AP is switched off.
Figure 17
4.3.3.3.
Tap on “menu”-“device”-“+add a new device”-choose the model of WS6210 from the Product listing. Tap on the cell marked with “WIFI provisioning”.
20

Figure 18
4.3.3.4. Connect to WS6210’s AP
In the wireless network list of your device (PC, tablet, Smartphone) select the SSID of the WS6210 (WS6210x-WIFIxxxx). Keep the Wi-Fi connection even without an internet connection.
Figure 19 21

4.3.3.5. Switch the cellphone’s WIFI to the same one as the WS6210.
Figure 20
4.3.3.6. Wait for the data to be uploaded You can see the battery level on dashboard.
Figure 21 22

4.4 How to delete and reset WS6210 Long press the WS6210 till the delete icon appears, press it, then choose Delete or Reset.
Figure 22
5. General Setting and Checkup
After completing the Network configuration, you can set the device for its’ device name, location, Time zone, DST (Daylight Saving Time), and Data public settings. 1. Tap on Menu and then click on “My Devices”. 2. Click the “… with a red new” icon to open the editing page.
23

Figure 23
Version: The current firmware version is displayed here. If an update is available, a “yellow arrow” will appear next to the version number. Tap on the version button to start the upgrade.
Figure 24
Device Name: You can edit your device name here if the default name needs to be changed. Device Location: Your device’s weather map location is determined by
24

its coordinates. You can change its location by tapping the location cell to open the weather map. You can drag and drop your WS6210 gateway on the map; its coordinates will be updated automatically.
Figure 25
25

Note 1: After the above device setting is completed, return to the dashboard. If the network connection is successful, the dashboard will display as follows:
Figure 26 Connection is Succeed
Note 2: The above dashboard should appear immediately with a Wi-Fi connection, and a cellular connection will be activated within 60 minutes. If the device shows an offline status, please refer to section 8.9 for more details.
Figure 27 Connection is failed 26

6. Sensor start up
1. Ensure the gateway is in sensor learning mode. Hold the Reset button for 3 seconds will turn on the receiver and will be in sensor learning mode. The RF LED will flash two times per second for 3 minutes until the learning process is completed. 2. Power up the sensor. Power up your sensor array, and the Web-UI dashboard should be able to show up the sensor data on the dashboard immediately after registration . If all data looks normal, you can temporarily store the gateway and sensor to ensure the system works. Then, refer to section 7 and complete the installation in its permanent location. For sensor mounting, you may refer to the specific sensor instruction manual. 3. Sensor ID confirmation Ensure that the sensor ID from which the receiver is receiving data matches the sensor ID on the label of the sensor array body. You can check sensor ID on the Web-UI dashboard. Reference to Section 8.7 for detailed instructions.
27

7. Mounting
7.1 Solar Panel Size
Figure 28
7.2 Mounting Before installation, please ensure that the product has been set up correctly. You may skip this part until the setup is completed. The accessory supports two range of pole widths. Prepare a support pole with a diameter of 1.8-2.75 inches (46mm-70mm) or 0.83-1.50 inches (21mm-38mm) in an open field with adequate lighting. Ensure the outdoor environment’s 4G cell phone signal is sufficiently strong. Tip: It is recommended to fully charge the device via USB cable before mounting.
28

1. Mount the Solar Panel onto the pole
Figure 29
2. Tighten the screws to secure the enclosure
Figure 30
The enclosure is closed by default. If you need to replace the SD card or SIM card, you will need to open it. Otherwise, it should remain closed. 3. Mount the WS6210 onto the pole
29

4. Mounting completed

Figure 31

Figure 32 30

8. Web UI On WS6210
The Web UI is an essential tool for managing the device. You can use it to check the network connection status, set up weather services (WU, WOW, Weather Cloud, custom server), view live data, manage sensors, make calibrations, manage SD card files, and more.
How to Access the Web UI: Make sure WS6210 is unlocked. Holding the AP Button for 5 seconds will turn on its Wi-Fi AP for 5 minutes. Connect to the WS6210’s AP. Enter 192.168.4.1 in the browser. Log in with the default username and password, which are blank. If your gateway is connected to a local network, the WebUI can also be reached via the IP address the gateway has received or has been configured: http://IP-address-of-the-gateway (e.g. http://192.168.1.123) Settings changes, such as registered Sensor IDs, are saved three minutes after power-up. However, changes made via the web interface are saved immediately and retained even if power is lost.
8.1 Local Network This page supports viewing or setting (1) MAC address (2) WLAN: WLAN is the function of the gateway’s Wi-Fi connection router, which is disabled by default Note: Make sure to deactivate the WLAN when the system is powered up by the solar panel.
31

(3) IP Address Mode: Receive Automatically (DHCP) or Static

8.2 Weather Services

Figure 33

After the Network configuration is successful, data can be uploaded to the following weather station servers: A. ecowitt.net (Default upload to this server) B. wunderground.com C. weathercloud.net D. wow.metoffice.gov.uk E. one Customized server of your choice

8.3 Device Setting

Figure 34

This page supports viewing or setting:
(1) Device sensor reception frequency (view only)
(2) Automatic Frequency Control (AFC): turn this option on when your location is busy on the sensor radio spectrum to improve signal reception.
(3) Temperature Compensation: Turn on this option to minimize sun light influence on outdoor temperature measurement if the outdoor temperature and humidity sensor installation site is not ideal. This option works with sensor arrays like WS69, WS80, WS90 and WS85.

(4) Auto Time zone: Your time zone setting on ecowitt.net will be applied here. (5) Automatic firmware upgrade (6) Device AP Auto OFF: Enabled by default, the AP automatically shuts down when no terminals are connected; disabling this option keeps the AP continuously running. If using the system only solar-powered, do not disable this setting. (7) Login & AP Password (8) Restore default: During factory Reset, all indicators will flash 3 times (ON: 500ms; OFF: 500ms), followed by an automatic restart upon completion.
Figure 35 34

8.4 Unit Settings Supports the following unit settings: (1) Temperature: , (2) Pressure: hPa, inHg, mmHg (3) Wind: m/s, km/h, mph, knots Note: Lightning distance units are the same as wind speed units:

Wind Speed Unit
m/s, km/h, BFT(BFT can only be set in App/ website)
knots
mph, fpm(fpm can only be set in App/website)
Table 7 (4) Rain: mm, in (5) Solar Irradiance: Klux, W/, Kfc

Lightning Distance Unit km nmi mi

Figure 36
8.5 Calibration This page supports the following data calibration: (1) Solar Irradiance (2) UV (3) Wind Speed (4) Indoor Temperature (5) Indoor Humidity (6) Absolute Pressure (7) Relative Pressure (8) Outdoor Temperature (9) Outdoor Humidity (10) Wind Direction
36

Figure 37
As well as: (11) Soil Moisture (12) Multi-Channel Temperature & Humidity (13) Multi-Channel Temperature
37

Figure 38 Figure 39
38

Figure 40
8.6 Rain Totals
This page supports settings such as: (1) Choose traditional or piezoelectric rain gauge data to be uploaded to the WU server, as only one rain gauge data can be accepted when you have both our haptic rain gauge and tipping bucket type rain gauge. (2) Rainfall calibration (3) Rain reset time for Daily Rain/Weekly Rain/Rainfall Season (4) For Piezo Rain1~5 Gain calibration Piezoelectric rain gauge working principle: raindrops fall on the sensor’s surface so that the monitoring panel produces small mechanical vibration, the vibration of the mechanical stress, and the sensor produces a voltage difference corresponding to the amount of rainfall. In practice, the measurement of precipitation by piezoelectric rain gauges is influenced by environmental factors such as wind, terrain, and debris. In the case of large rainfall intensity, rainfall intensity
39

can be measured by the piezoelectric rain gauge, but the raindrops landing may have two impacts on the monitoring panel so that the measured rainfall value is larger; for minimal rainfall intensity, due to the vertical momentum is too small, so that the measured rainfall value is small. Therefore, it is necessary to calibrate the piezoelectric sensors for different rainfall intensities depending on the environment in which they are located. WS90 and WS85 are weather stations equipped with piezoelectric rain gauges. To make your rain data more accurate, you can calibrate the rain sensor accuracy by yourself: 1. A reference is needed to record the rainfall value, and it is also important to be able to record the rain rate. Our WH40 rain sensor can be used for this purpose. 2. You can set five rain gain parameters: Piezo Rain1: Rain5. We usually leave Rain1 as it is unless you can confirm it consistently produces the same result, and then you can adjust this. 3. Please ensure that you record rain data as follows: set rain4 gain to 6/7.5, which equals 0.8. For easier management, set rain2, rain3, and rain5 all to 0.8 for now. Only when different rain rates are recorded, divide the ws90 rain by 0.8 to get 1.0 rain, and then recalculate (reference/ws90/0.8) to precisely adjust the corresponding rain gain setting.
40

Figure 41 41

8.7 Sensors ID (1) Supports viewing and registering sensor ID. (2) Viewing battery status and signal quality. (3) By entering the “Edit” sub-page of a particular sensor, you may register the sensor by entering the sensor ID so that this sensor can be mandatorily assigned. You can also choose to disable the sensor. It is good practice to disable all sensor ID slots of sensors which you don’t have or don’t use with your console/gateway in order to avoid the reception of “ghost” sensors from other weather stations in your neighbourhood. (4) By entering the “Re-register,” the gateway will learn the sensor again to ensure its presence. If a new sensor is discovered, it will be displayed here with its sensor ID updated.
42

Figure 42 43

Figure 43 44

8.8 Live Data (1) Display connected sensor data. (2) Show WS6210’s battery voltage and solar charging power supply voltage. (3) You can edit the sensor name by clicking the pencil icon. This name is only reflected on this device, it will not update your dashboard tile name at ecowitt.net.
Figure 44 45

8.9 Modem Management 7.9.1 Management Page Description (1) Display basic information of the Modem: SIM Card: Inserted or Not Inserted RSSI: Signal strength, used to measure signal quality IMSI: International Mobile Subscriber Identity, used to identify a SIM card uniquely IMEI: International Mobile Equipment Identity, used to identify a 4G module uniquely ICCID: Integrated Circuit Card Identifier, a unique identifier for the SIM card IP address: Currently assigned local area network IP address Registered Operator: The operator with which the device is registered Network Standard: Network protocol and frequency bands supported by the device APN: Access Point Name, used for data communication and can be edited. Correct APN settings are necessary for proper use if using a custom SIM card Modem Model: Model of the 4G module Modem Version: Firmware version of the 4G module
(2) Support real-time display of Modem Log (3) Support downloading Modem Log to local storage
46

Figure 45
Check the top section to see if it was successful. Click “Download” to download the SIM card data log. The log file reveals the cellular network connection status in detail. It is useful when you need to investigate the connection in detail. Thus, downloading the log and sending it to customer support is quite useful when you seek help.
47

8.9.2 Troubleshooting Modem Issues
(1) Communication Issue with 4G Module Symptom: On the Modem Management page of the WebUI, SIM Card status shows “Not Inserted” and the Log only displays “-> AT”.
Figure 46
Analysis: Failure in communication between the main control and the module. Solution: Try power cycling the device. If the issue persists, the 4G module may be damaged or there could be a circuitry issue, requiring replacement of the 4G module board.
48

(2) SIM Card Not Detected Symptom: On the Modem Management page of the WEB UI, SIM Card status shows “Not Inserted” and the Log shows “-> AT+CPIN?” followed by “<- +CME ERROR: 10”.
Figure 47
Analysis: Possible reasons include SIM card not inserted properly, loose SIM card, damaged SIM card, or faulty 4G module board. Solution: Verify SIM card readiness, replace SIM card if necessary, or replace the 4G module board.
49

(3) Poor Network Signal Strength Symptom: On the Modem Management page of the WEB UI, SIM Card status shows “Inserted” and the Log repeatedly shows “-> AT+CSQ” followed by “<- +CSQ: 99,99”.
Figure 48
Analysis: Repeated occurrences of “-> AT+CSQ” and “<- +CSQ: 99,99” indicate poor network signal quality. Solution: Check the antenna connection and verify SIM card quality. (4) SIM Card Attach to Network Failure Symptom: On the Modem Management page of the WEB UI, SIM Card status shows “Inserted” and the Log shows multiple occurrences of “<+CREG: 0,5”, “<- +CREG: 0,1”, and “<- +CGATT: 0”.
50

Figure 49
Analysis: “<- +CREG: 0,5” and “<- +CREG: 0,1” indicate successful registration, while “<- +CGATT: 0” indicates failure to attach to the network. This could be due to SIM card being tied to a specific IMEI or running out of data. Solution: Check SIM card status (payment, validity) or replace SIM card if necessary.
(5) SIM Card Internet Connection Issue Symptom: On the Modem Management page of the WebUI, SIM Card status shows “Inserted” and the 4G module obtains an IP address, but the Log displays “<- +CDNSGIP: 0,8”.
51

Figure 50
Analysis: Indicates a problem with the SIM card. Solution: Check SIM card status (payment, validity) or replace SIM card if necessary.
52

8.10 SD Card Management
(1) SD card file system format: Only FAT32 is supported. For cards larger than 32GB, use the Rufus tool to format the SD card to FAT32. Download the tool from https://rufus.ie/en/.
Tip: When replacing with a higher-capacity card, please be mindful of the memory card’s maximum read/write cycles and lifespan.
(2) Real-time status display and hot-swap support: The system monitors the SD card’s status in real-time and allows for its insertion or removal without restarting the device.
(3) SD card information display: The interface shows detailed SD card information, including storage capacity and read/write frequency.
(4) Multi-level directory management: The system adopts a multi-level directory structure for easy file categorization and management by users.
(5) Sensor data storage: Data collected by sensors is saved in .csv format in the root directory of the SD card, facilitating direct access and analysis of data.
(6) Log file management: The system generates new log files daily, saved in .txt format. All log files are automatically categorized and stored in respective folders by month, facilitating retrieval and management of historical data.
(7) File filtering mechanism: The system automatically filters out non-gateway-generated files, ensuring storage space is allocated for important data and avoiding unnecessary data redundancy.
(8) File operations support: Users can download and delete individual files, providing flexible file management capabilities.
(9) Customizable save intervals: The system allows users to adjust save intervals for data and log files according to specific recording needs.
53

Figure 51 54

8.11 Firmware updates
Firmware Automatic Upgrade: If automatic firmware update is enabled on the web interface and new firmware is detected, the product will enter OTA (over the air, here: WiFi or 4G) mode and automatically restart upon completion. (Automatic update check interval is 24 hours) Manual Upgrade: Access the local web page (either via the gateway AP 192.168.1.4 or via the local network http://IP-address-of-the-gateway, navigate to the device settings page, click on ‘Check Version,’ and if a new version is found, click “Upgrade Version.”
Figure 52 55

9. Product Features
Networking: Supports Wi-Fi and 4G, prioritizing Wi-Fi for data upload to the weather station server if available.
Sensor Support: Receives data from almost all ecowitt sensors, viewable via a web interface and Ecowitt app.
Web Functions: Supports web configuration, sensor data viewing, server settings, calibration parameters, and Sensor ID settings.
IoT Functionality: Compatible with IoT devices: WFC01 and AC1100.
Automation: Automatic time zone and network time acquisition, unit settings.
Models for 433MHz, 868MHz, 915MHz (and 920.9MHz) available. Integrated SD card data management: no extra APP or tools needed.

10. Specifications

Model

WS6210

Name Dimensions
Weight
Material of Plastic Casing
Sim card SD card

4G & Wi-Fi Weather Station Receiver Mobile Gateway 187*138*55(mm) L*W*H 694.5g (8 batteries involved) 457g (WS6210 only)
PC
Nano-SIM 8G Micro SD

Cellular and Wireless
Supported Brand
RF Connection Frequency RF Wireless Range WLAN WLAN
Wireless Range
Power Supply
Indicator Light
Button
Operating Temperature Port Material
Battery Capacity
Battery Life

Support LTE 3GPP Rel.13 technology, support 4G network
4G LTE-FDD B1/B2/B3/B4/B5/B7/B8/B12/B13/B17/B18/B19/B20/B25/B 26/B28/B66 4G LTE-TDD B34/B38/B39/B40/B41 2G GSM 850/900/1800/1900
920/915/868/433MHz (depending on local regulations)
Over 100 meters (in open areas)
802.11 b/g/n 2.4 GHz (802.11n, Max 150 Mbps)
Over 30 meters (in open areas)
12V solar panel (or DC power supply with USB connector, input 5-15V, not included) Unlock, RF, Wi-Fi, 4G Touch button: Reset, AP Physical button: Power
-20 to 60 (-4 to 140°F)
2-core waterproof aviation connector
4800 mAh @5V
20 days (5-minute upload interval, AP off, not connected to IoT Sub device) 10 days (5-minute upload interval, AP off, connected to IoT Sub device)

Power Consumption

0.06W, 10mA (AP off, not connected to IoT)
0.12W, 20mA (AP off, connected to IoT)
0.9W, 150mA (AP on, connected to Wi-Fi, not connected to IoT)
0.96W, 160mA (AP on, connected to Wi-Fi, connected to IoT)
0.8W, 133mA(AP off, connected to WiFi, not connected to loT) 0.85W, 142mAAP off, connected to WiFi, connected to loT)
While in a 5-minute upload interval

USB charging 5V, 1A

Solar Panel charging power
Solar Panel Size

7W 270*180*17(mm)L*W*H

Posting intervals

By default: 5 minutes
The setting range is “off, 1, 2, 3, 4, 5, 10 minutes.” Shortening the posting interval will increase power consumption

SD13 to USB Length 50cm(19.7 inch) power cable

Solar panel cable

Length 70cm(27.6 inch)
Table 8

11. Miscellaneous
11.1 Replacing the SD/SIM Card
1. Locate the SD/SIM Card Slot Open the device casing with a Phillips screwdriver as per the manual’s instructions

2. Access the SD/SIM Card Slot 3. Install the SD/SIM Card
4. Close the SD/SIM Card Slot Cover
5. Verify Proper Installation
6. Secure the Device Casing 7.Enter the correct APN.

Press down on the cover and pry it open gently, using a fingernail or a similar tool. Insert the SD/SIM card into the slot with the metal contacts facing down. Ensure it aligns correctly. Push the cover back in place gently. Ensure it closes tightly; if not, recheck the card’s placement. Check if the SD/SIM card is functioning properly after installation. Reattach the device casing securely. To configure a new SIM card, please refer to Section 8.9 for instructions.

Table 9

11.2 Manually Adding
For users who have already set up the network, follow these steps to manually add the WS6210 device.

Instructions

Illustration

1.Obtaining MAC Address
*The MAC address can be found on the label of the device or via Embedded Web Page.

label of the device

Embedded Web Page 60

2.Click on Other, and choose Manually Adding.

3.Manually Enter the MAC Address. Then wait approximately 30-60 minutes for the data to upload when in 4G mode .

Table 10

11.3 SIM Card Renewal Instructions

Illustration

1.When the SIM card is about to expire, the interface will display a “subscribe” icon. Click on the “…”.

2.Select the appropriate plan and click “subscribe.”

3.After successful payment, click “back.” Please note that on ios, you cannot directly return to the Ecowitt app.
4.Once the renewal is successful, check if the
validity period has been updated.
Table 11 63

12. Optional Sensors
The product supports receiving data from various sensors, which can be used with the Ecowitt server for enhanced data services. The RF reception function will always be turned on to receive data from all registered sensors anytime. 12.1 Sensor Data Reception Priority
Please note that data processing is prioritized when there is more than one sensor array or a rainfall sensor for outdoor temperature, wind, rain and solar data where applicable registered in the gateway (sensor hierarchy). Sensor Array Priority:WS85>WS90>WS80>WS68>WS69. Piezo rainfall priority: WS85>WS90 Traditional rainfall Priority: WH40>WS69. 12.2 Sensors
The following sensors can be purchased separately. For more information, please visit our website: http://www.ecowitt.com. Select the model of the units with the same RF frequency as your gateway or display (the frequency is different for various countries because of regulations). Notes: (1) The max QTY in the following table indicates the maximum number of the same sensor model or type that can be connected to the WS6210. (2) Theoretically all the different sensor arrays (WS68, 69, 80, 85, 90) could be connected to one gateway at the same time, but due to the sensor hierarchy (see above) this would only make sense in a few special cases (e.g. WS85 + WS68 (get solar data from WS68). WS85 or WS90 + WS69 (get traditional rain data from the WS69).
64

Sensor Model

Max QTY

Picture

WS90

WS85

WS80

WS69

Functions
Outdoor temperature & humidity, light, UV, wind speed/direction, rainfall
Wind speed/direction, rainfall
Outdoor temperature & humidity, light, UV, wind
speed/direction Outdoor temperature & humidity, light, UV, wind speed/direction, rainfall

WS68

Light, UV, wind speed/ direction

WH40

WN32P

WN32

WH45/(WH46) 1

Rainfall
Indoor temperature, humidity, and pressure
Outdoor temperature and humidity
WH45: CO, PM2.5, PM10, temperature and humidity WH46: CO, PM1.0, PM2.5, PM4.0, PM10, temperature and
humidity

WN31

Temperature and humidity

WN30

Temperature

WN36

WH57

WH41/WH43 4

WH55

Pool temperature Lightning detection
PM2.5 Water leak detection

WH51L 16*
WH51

Soil moisture Soil moisture

WN34L/S/D

Temperature

WN35

Leaf wetness

Table 12 Optional sensors
*–Refers to the maximum number of sensors in this group. Any combin ation that sums up to the number mentioned is possible.

12.3 IoT Device
Sensor Model Max QTY Picture

Functions

WFC01 16*
AC1100

Smart water timer Smart plug

*–See Above

Table 13 IoT device

13. Warranty
We disclaim any responsibility for any technical error or printing error or the consequences thereof. All trademarks and patents are recognized. We provide a 2-year limited warranty on this product against manufacturing defects or defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased, and only to the original purchaser of this product. To receive warranty service, the purchaser must contact us for problem determination and service procedures. This limited warranty covers only actual defects within the product itself and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, or claims based on misrepresentation by the seller, or performance variations resulting from installation-related circumstances.
Manufacturer: Shenzhen Fine Offset Electronics Co., Ltd. Address: 4/F, Block C, JiuJiu Industrial City, Shajing Town, Baoan District, Shenzhen City, China
68

14. FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
69

To maintain compliance with RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
IC Caution: English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. French: L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
70

15. Care and Maintenance
When batteries of different brand or type are used together, or new and old batteries are used together, some batteries may be over-discharged due to a difference of voltage or capacity. This can result in venting, leakage, and rupture and may cause personal injury. · Do not mix Alkaline, Lithium, standard, or rechargeable batteries. · Always purchase the correct size and grade of battery most suitable for the intended use. · Always replace the whole set of batteries at one time, taking care not to mix old and new ones, or batteries of different types. · Clean the battery contacts and also those of the device prior to battery installation. · Ensure the batteries are installed correctly with regard to polarity (+ and -). · Remove batteries from product during periods of non-use. Battery leakage can cause corrosion and damage to this product. · Remove used batteries promptly. · For recycling and disposal of batteries, and to protect the environment, please check the internet or your local phone directory for local recycling centers and/or follow local government regulations
71

16. Contact Us
16.1 After-sales Service Order Issues: If you encounter any missing or incorrect shipments of Ecowitt products purchased, please reach out to the respective platform’s customer service from the store where you bought the product for assistance.
Usage Inquiries: Our product is continuously changing and improving, particularly online services and associated applications. To download the latest manual, and additional help, and for any issues related to product usage feel free to contact our customer support team at support@ecowitt.com. We are committed to providing assistance and resolving any concerns you may have.
16.2 Stay in Touch Ask questions, watch setup videos, and provide feedback on our social media outlets. Follow Ecowitt on Discord, YouTube, Facebook and Twitter.
Copyright © 2025 ecowitt All Rights Reserved. DC061625
72

Documents / Resources

ecowitt WS6210 4G and Wi-Fi Weather Station Mobile Gateway [pdf] User Manual
WS6210, WS6210 4G and Wi-Fi Weather Station Mobile Gateway, 4G and Wi-Fi Weather Station Mobile Gateway, Wi-Fi Weather Station Mobile Gateway, Weather Station Mobile Gateway, Station Mobile Gateway, Mobile Gateway, Gateway

References

User Manual

ecowitt WS6210 4G and Wi-Fi Weather Station Mobile Gateway User Manual

WS6210 4G and Wi-Fi Weather Station Mobile Gateway

Specifications

Product Usage Instructions

1. Package Contents

2. Construction & Layout

2.1 Multiple Views and Size

2.2 Layout

2.3 Light Indicators

2.4 Touch Button

3. Brief Introduction

FAQ (Frequently Asked Questions)

Q: How do I connect the WS6210 to my Wi-Fi network?

Q: What is the purpose of the touch buttons on the WS6210?

Documents / Resources

References

Leave a comment

Cancel reply