ECG-logo

ECG FT 23 Table Fan User Manual

ECG-FT 23-Table-Fan-product

Always read the safety and use instructions carefully before using your appliance for the first time. The user´s manual must be always included.

SAFETY INSTRUCTIONS
Read carefully and save for future use!

Warning: The safety measures and instructions, contained in this manual, do not include all conditions and situations possible. The user must understand that common sense, caution, and care are factors that cannot be integrated into any product. Therefore, these factors shall be ensured by the user/s using and operating this appliance. We are not liable for damages caused during shipping, by incorrect use, voltage fluctuation or the modification or adjustment of any part of the appliance.
To protect against a risk of electric shock, basic precautions shall be taken while using electrical appliances, including the following:

  1. Make sure the voltage in your outlet corresponds to the voltage provided on the appliance label and that the socket is properly grounded. The outlet must be installed according to valid safety instructions.
  2. Do not operate the device with a damaged cord. All repairs including cord replacements shall be performed by a professional service centre! Do not remove protective covers of the appliance, risk of electric shock!
  3. Protect the device against direct contact with water and other liquids, to prevent potential electric shock.
  4. The product is intended only for household use! Do not operate the fan outdoors or in a moist environment and do not touch the cord or appliance with wet hands. Risk of electric shock.
  5. Close supervision is necessary for operating the fan near children!
  6. Place the fan out of reach of other objects to ensure sufficient circulation needed for its proper operation. Do not cover the fan vents!
  7. Do not use this fan with a program, timer, independent remote control system or any other device, which switches the fan on automatically. Risk of fire, rfirethe fan is covered or incorrectly positioned.
  8. Do not use the fan in the area, where heat is accumulated (near the stove, heater, etc.).
  9. Do not place the fan onto a soft surface, such as a bed, sofa, etc. It must be placed on a stable and flat surface.
  10. If an unusual smell or smoke begins to come from the device, disconnect the device immediately and visit a service centre.
  11. Do not turn the device on or off by plugging or unplugging the power cord. Always turn the fan off using the main switch; afterward, you may unplug the cord from the outlet!
  12. Leaving the fan cord connected to the outlet unattended is not recommended. Disconnect the cord from the electrical outlet before performing maintenance. Do not pull the cord from the outlet by yanking the cord. Unplug the cord from the outlet by grasping the plug.
  13. Do not allow the cord to touch hot surfaces or lead the cord over sharp edges.
  14. Do not put your fingers or other objects into the openings of the fan.
  15. Use the fanonlyy in theinstructions given in this manual. The manufacturer is not liable for damages caused by the improper use of this appliance.
  16. This appliance is intended for household use and similar areas, including:
    • kitchen corners in markets, offices, and other workplaces
    • appliances used in the agricultural industry
    • appliances used by guests in hotels, motels, and other residential areas
    • appliances used in bed and breakfast businesses
  17. This appliance can be used by children ages 8 and older and by the physically and mentally impaired or by individuals with insufficient experience and knowledge, if supervised or trained to use the appliance safely and understand potential dangers. Children shall not play with the appliance. Cleaning and maintenance operations performed by the user shall not be carried out by children without supervision.

Do not immerse in water!
Warning: To prevent overheating, do not cover the fan. The fan must not be placed directly under an outlet.

INSTALLATION

  1. Unscrew the nut that attaches the back screen by turning it counter-clockwise.
  2. Place the back screen opposite of the front motor cover with the handle facing upward. Make sure the guide pins of the motor cover are properly inserted into the screen holes.
  3. Screw the nut for attaching the back screen fi rmly to the motor by turning it clockwise.
  4. Remove the plastic protector from the shaft.
  5. Place the propeller on the motor shaft by carefully sliding it onto the guide pin of the motor shaft.
  6. Screw the nut for attaching the propeller to the motor shaft by rotating it counter-clockwise and tighten fi rmly.
  7. Attach the front screen to the back screen. Insert the screws in the holes of the ring and screw nuts on to these. Do not tighten the nuts completely at this time.
  8. Move the screen pins so they fall into place.
  9. Finally, tighten the small screws fi rmly.

Product Overview

ECG-FT 23-Table-Fan-fig- (1)

  1. Front guard
  2. Fan blade
  3. Guard mounting nut
  4. Rear guard
  5. Motor shaft
  6. Motor housing
  7. Oscillation k nob
  8. Motor
  9. Neck piece assembly
  10. Stand
  11. Power cord
  12. Speed control switch (0, 1, 2)

Note: You may register radio interference while switching fan speeds, this eff ect is normal for this kind of product.

HEAT PROTECTION
Heat protection is activated if an actuating unit is overloaded. The fan switches off automatically. In this case, refer to a professional service centre.

USE

The fan has 2 speeds, its rotating head ensures smooth rotation. It is quiet, with a low energy consumption, reliable and safe and at the same time, ensures eff ective air circulation.

0 – Fan is of.
1 – Fan is running at low speed.
2 – Fan is running at high speed.

  • The fan can rotate during operation.
  • For the fan head to rotate, push the automatic rotation control down.
  • To stop the rotation of the fan head, pull the automatic rotation control up.
  • The fan head can be set up or down. Loosen the vertical setting nut, adjust the desired angle of the fan and tighten the nut again.

CLEANING AND MAINTENANCE

  1. The fan must be switched off and the cord disconnected from the outlet before cleaning.
  2. Wipe the plastic parts with a towel or moist sponge dipped into a soap agent. Wipe dry. Do not immerse the fan into water!
  3. To dismantle the fan, proceed in the opposite sequence as for the assembly process.
    We recommend keeping the package for transporting the fan or storage.

TECHNICAL INFORMATION

  • Diameter 23 cm
  • Nominal voltage: 230 V~ 50 Hz
  • Nominal input power: 30 W
  • Noise level: 60 dB

USE AND DISPOSAL OF WASTE
Wrapping paper and corrugated paperboard – deliver to scrapyard. Packing foil, PE bags, plastic elements – throw into plastic recycling containers.

ECG-FT 23-Table-Fan-fig- (2)DISPOSAL OF PRODUCTS AT THE END OF LIFETIME
Disposal of electric and electronic equipment (valid in EU member countries and other European countries with an implemented recycling system) The represented symbol on the product or package means the product shall not be treated as domestic waste. Hand over the product to the specified location for recycling electric and electronic equipment. Prevent negative impacts on human health and the environment by properly recycling your product.

Recycling contributes to preserving natural resources. For more information on the recycling of this product, refer to your local authority, domestic waste processing organization or store, where you purchased the product. This product complies with EU directive requirements on electromagnetic compatibility and electrical safety. The instruction manual is available at the website www.ecg-electro.eu. Changes in text and technical parameters reserved. The importer takes no responsibility for printing errors contained in the product’s user’s manual.

Download PDF: ECG FT 23 Table Fan User Manual

References

Leave a comment

Your email address will not be published. Required fields are marked *