Eccel Pepper C1 PoE Module

Specifications
Electrical Specification
Absolute maximum ratings
- Stresses beyond the absolute maximum ratings listed in the table below may cause permanent damage to the device. These are stress ratings only, and do not refer to the functional operation of the device that should follow the recommended operating conditions.
| Symbol | Parameter | Min | Max | Unit |
| TS | Storage temperature | -40 | +125 | °C |
| TA | Ambient temperature | -40 | +85 | °C |
| VDDMAX | USB supply voltage | 5 | 5.5 | V |
Operating conditions
| Symbol | Parameter | Min | Typ. | Max | Unit |
| TS | Operating temperature | -25 | 25 | +85 | °C |
| H | Humidity | 5 | 60 | 95 | % |
| VDD | USB supply voltage | 5 | 5 | 5.5 | V |
DC characteristics (VDD = 5 V, TS = 25 °C)
| Symbol | Parameter | Min | Typ. | Max | Unit |
| VOUT3.3 | Output voltage (regulator output, 3V3 pin on the J3 header) | 3.23 | 3.3 | 3.37 | V |
| VOUT5 | Output voltage (regulator output, 5V pin on the J3 header) | 4.8 | 5 | 5.2 | V |
| VIH | High-level input voltage (J3 header) | 0.75 x VOUT3.3 | – | VOUT3.3 + 0.3 | V |
| VIL | Low-level input voltage (J3 header) | 0 | – | 0.3 x VOUT3.3 | V |
| VOH | High-level output voltage (J3 header) | 0.8 x VOUT3.3 | – | – | V |
| VOL | Low-level output voltage (J3 header) | – | – | 0.3 x VOUT3.3 | V |
Current consumption (VDD = 5V)
| Symbol | Parameter | Typ. | Max | Unit | ||
| Wi-Fi enabled | Access Point mode | IPN_RFOFF_AP | RF field off (AP) | 150 | 170 | mA |
| IPN_RFON_AP | RF field on (AP) | 190 | 210 | mA | ||
|
Station mode |
IPN_RFOFF_STA | RF field off (STA) | 75 | 95 | mA | |
| IPN_RFON_STA | RF field on (STA) | 130 | 150 | mA | ||
| Wi-Fi Off | IPN_RFOFF | RF field off | 65 | 70 | mA | |
| IPN_RFON | RF field on | 120 | 140 | mA | ||
Product Usage Instructions
Introduction
Description:
This product is designed for users who want to add RFID capability to their projects quickly and easily. The device features a powerful 32-bit microcontroller that simplifies RFID configuration setup and provides a user-friendly command interface for efficient read/write access to supported transponders.
Getting Started
IO and Peripherals
The Pepper C1 POE PCB features various components:
- RJ45 socket
- External RFID antenna connector (J6)
- USB-C socket
- J3 header
- Button ANT2 socket for external 2.4GHz antenna
- RGB LED
J3 Header Description
The J3 header provides access to the following:
- Output voltage (regulator output, 3V3 pin)
- Output voltage (regulator output, 5V pin)
J6 External Antenna Header
To use an external RFID antenna with the Pepper C1 POE reader:
- Connect the external antenna to the J6 connector.
- Soldering may be required for proper functionality.
- Eccel Technology Ltd offers compatible RFID antennas for use with this device.
1 The newest User manual can be found on our website: https://eccel.co.uk/wp-content/downloads/Pepper-C1/C1-POE-user-manual.pdf
Introduction
Device Overview
Features
- Low cost RFID Reader with MIFARE® Classic® in 1K, 4K memory, ICODE, MIFARE Ultralight®, MIFARE DESFire® EV1/EV2, MIFARE Plus® support
- Ethernet + PoE
- USB interface (USB-C socket)
- Wireless connectivity:
- Wi-Fi: 802.11 b/g/n
- 2.4GHz wireless communication (BR/EDR and Low Energy)
- can be disabled by the user
- Built-in Web Interface
- Over-The-Air lifetime updates
- Command interface via UART and TCP sockets
- Configurable RGB LED indicator for RFID events
- 1 configurable IO pin, 2 x input pins
- Stand-alone mode (polling)
- IoT interfaces: MQTT, WebSocket, REST API
- High transponder read and write speed
- -25°C to 85°C operating range
- RoHS compliant
- CE (RED) and UKCA compliant.
- FCC/ISED/PSE and other approvals easily obtained (see section 7)
Applications
- Access control
- Monitoring goods
- Approval and monitoring consumables
- Pre-payment systems
- Managing resources
- Contactless data storage systems
- Evaluation and development of RFID systems
Description
- The Pepper C1 PoE reader is the first Eccel Technology Ltd product with wired connectivity by Ethernet interface, as well as wireless Wi-Fi 802.11b/g/n and WPAN (BR/EDR + LE). Thanks to this, the customer receives free lifetime Over-the-Air updates, and of course the communication protocol can be used over TCP instead of traditional serial interface. Combining these features with standalone mode provides a ready to use device in many applications “straight out of the box.” In standalone mode, the module can be easily integrated with IOT systems thanks to many IOT protocols like MQTT, REST API, TCP sockets and more.
- So, this is an ideal design choice if the user wishes to add RFID capability to their design quickly and without requiring extensive RFID and embedded software expertise and time. An advanced and powerful 32-bit microcontroller handles the RFID configuration setup and provides the user with a powerful yet simple command interface to facilitate fast and easy read/write access to the memory and features of the various transponders supported by this module.
Getting started
IO and peripherals

J3 header description

- Ground
- +5V output (300mA max.)
- IO32 – UART2 TX, debug TX, general purpose IO pin
- IO20 – (NC, RFU)
- Ground
- I34 – UART2 RX
- +3.3V output (500mA max.)
- I35 – general purpose input pin
J6 External antenna header
- The user has the option to connect an external RFID antenna to the Pepper C1 POE reader. The J6 connector is where to plug in an external antenna, but some soldering shown on the pictures below is required to make it work. Eccel
- Technology Ltd provides a variety of RFID antennas which the user can use together with this device.
- See our range of external PCB antennas (the green ones):

- GND
- Antenna TX1 – RFID driver output
- Antenna TX2 – RFID driver output
- GND

Ethernet + PoE interface
The Pepper C1 PoE reader features a 10/100 Mbps Ethernet interface based on the LAN8720A PHY chip, enabling reliable network communication. Additionally, the device supports Power over Ethernet (PoE) functionality, which supplies both data and power over a single twisted-pair Ethernet cable. This simplifies installation by eliminating the need for a separate power supply.
- PoE functionality is implemented using the Si3402-C-GM power management IC, which complies with the IEEE 802.3af standard. The device is fully compatible with IEEE 802.3 Type 1 (Class 3 and below) Powered Device applications, supporting a power budget of up to 15.4 W at the PSE (Power Sourcing Equipment) and up to 12.95 W available at the PD (Powered Device), depending on cable length and quality.
- The integrated RJ45 connector (Würth Elektronik 74984104400) includes built-in magnetics and is designed to support both Ethernet data transmission and PoE power delivery, in accordance with IEEE specifications.
For optimal performance and reliability, it is recommended to use standard-compliant PoE switches or injectors. Examples of compatible equipment include:
- Ubiquiti UniFi Switch (e.g., US-8-60W) – provides stable 802.3af PoE output and seamless network integration,
- TP-Link TL-SF1008P – 8-port switch with 4 PoE ports (IEEE 802.3af compliant),
- TP-Link TL-POE150S – standalone PoE injector compliant with IEEE 802.3af.
Using IEEE-compliant PoE equipment ensures proper power negotiation, safe operation, and long-term reliability of the Pepper C1 PoE reader in diverse installation environments.
Typical connection
- The Pepper C1 PoE was developed to use a PoE + LAN circuit to power it and provide network communication with the host server. It can also be connected to a host computer using a standard USB-C cable. In the same way it can be powered to operate as a standalone device by using power sources such as a USB charger or power bank.
- The computer operating system should recognize this device as a USB to TTL bridge or a USB to Serial port converter and it should appear in Windows device manager as a COM port. By default this COM port can be used for communication using the binary protocol described below.
- The reader also has the UART2 interface (J3 header) where the user can view console logs which contain additional information about temporary executing commands. The default configuration: baud: 115200, Data: 8 bit, Parity: none, Stop bits: 1 bit, Flow Control: none.

Hint – If you don’t have a USB-UART converter to see the logs on the UART2 (J1 header), you can temporarily change the default log interface from UART2 to UART0 in the Web Interface (Communication->UART tab). Then, the logs should be available on the USB port.

By default, both interfaces (LAN and Wi-Fi) are enabled. If the user connects only the USB-C cable (without the LAN cable), Wi-Fi will be available (Access Point or Client mode depending on the configuration). Each time the LAN cable is inserted, Wi-Fi will be disabled. Unplugging the LAN cable will re-enable Wi-Fi. This way, it will always be possible to connect to the reader via the Web Interface. LAN is always enabled. This can be configured in the Web Interface and saved in the non-volatile memory of the reader. More information can be found in the Pepper C1 software manual.
Plastic enclosure
Upon request, the Pepper C1 PoE reader can be supplied with a dedicated enclosure, designed to protect the electronics and facilitate easy installation in various environments. Additionally, we offer the option to redesign the PCB to match the customer’s specific mechanical requirements, allowing seamless integration of the reader into custom housings or existing device enclosures.

Mechanical dimension
All dimensions are in mm.

Configuration and functional description
- Here is the document describing configuration, communication protocol, commands and all functions of the Pepper C1 POE reader:
- Eccel provides a variety of free tools & libraries ready to be downloaded from this link:
Custom Integration Services
We offer integration services for embedding our RFID readers into customer end devices or systems. Our engineering team can assist in antenna tunning directly within the target environment to ensure optimal performance and reliability.
Additionally, we provide options for custom firmware development, as well as mechanical modifications – including changes to shape, mounting format or enclosure design – to meet customer-specific technical and design requirements.
Please contact us at sales@eccel.co.uk for more information.
RF Emissions and Susceptibility Approvals
- Eccel have tested and declare that this product meets all the requirements of the relevant RF directives (RED) to be declared CE (European Union) and UKCA (United Kingdom) compliant. Please see our declaration of conformity for this on the downloads tab of the product webpage.
- This product is designed to be incorporated into products easily and quickly such that those products can pass any national or regional statutory RF requirements and certifications such as FCC (USA), ISED (Canada) and PSE (Japan) for example.
- This product is designed to meet all statutory RF requirements applicable worldwide using the most cost effective but robust design methodology.
- Eccel is pleased to offer customers very cost-effective certification for their end equipment that incorporate this product. Prices start from £3K per approval/ certification. Please contact us for more details at sales@eccel.co.uk.
Revision history

MIFARE, MIFARE Ultralight, MIFARE Plus, MIFARE Classic, and MIFARE DESFire are trademarks of NXP B.V.
- No responsibility is taken for the method of integration or final use of the Pepper C1 readers
- More information about the Pepper C1 reader and other products can be found at the Internet site:
- http://www.eccel.co.uk or alternatively contact ECCEL Technology by e-mail at: sales@eccel.co.uk
FAQs
Q: What are the operating conditions of the device?
Q: How do I connect an external RFID antenna to the Pepper C1 POE reader?
Documents / Resources
![]() | Pepper C1 PoE Module |
References
- co.ukco.uk
- mailto:sales@eccel.co.ukeccel.co.uk
- HF (13.56 MHz) - Eccel Technology - RFID made simpleeccel.co.uk
- Support - Eccel Technology - RFID made simpleeccel.co.uk
- Custom RFID/NFC solutions for your bussiness - Eccel Technology - RFID made simplewww.eccel.co.uk
- User Manualmanual.tools

