ECARE ELECTRONICS TP960B Bluetooth Module

Product Overview

TP960B is a Intelligent wireless data transmission Bluetooth module developed by SHENZHEN ECARE ELECTRONICS CO., LTD. It consists of a highly integrated wireless radio chip (ASR5601) and several peripherals。

Features

• In practical applications, customers only need to install the corresponding firmware, connect to the application product, quickly establish a connection, and then they can control the product through instructions.
• This module can be easily connected to the Bluetooth devices of various digital products such as mobile phones, tablets and laptops. Through wireless data transmission, it enables the control of the products by sending instructions.

Major Application Fields

• Intelligent building
• Intelligent home and household applications
• Intelligent socket and light
• Industrial wireless control

Module Interfaces

Dimensions and Footprint
TP960B provides three rows of pins with the distance of 0 . 6 mm between every two pins.
TP960B dimensions: 15.2 mm (L) x 24.0 mm (H) (see figure 2)

Pin definition
Table 1 describes the interface pins and their functions.

PIN	Definition	Function
1	GND	GND
2	VDD	Power supply
3	P23	Digital and Analog GPIO
4	P24	Digital and Analog GPIO
5	P15	Digital and Analog GPIO
6	P16	Digital and Analog GPIO
7	P02	Digital GPIO/UART_RX
8	P03	Digital GPIO/UART_TX
9	P04	Digital GPIO/UART_RX
10	P05	Digital GPIO/UART_TX
11	P17	Digital and Analog GPIO
12	P18	Digital and Analog GPIO
13	P25	Digital and Analog GPIO
14	P26	Digital and Analog GPIO
15	P29	Digital and Analog GPIO
16	P08	Digital and Analog GPIO/ADC1
17	P09	Digital and Analog GPIO/ADC2
18	P13	Digital and Analog GPIO/ADC3
19	P14	Digital and Analog GPIO/ADC4
20	P21	Digital and Analog GPIO

21	P28	Digital and Analog GPIO
22	P27	Digital and Analog GPIO
23	P22	Digital and Analog GPIO
24	P07	Digital and Analog GPIO
25	P06	Digital and Analog GPIO
26	P11	Digital and Analog GPIO
27	P12	Digital and Analog GPIO
28	P00	Digital and Analog GPIO
29	P01	Digital and Analog GPIO
30	P19	Digital and Analog GPIO
31	P10	Digital and Analog GPIO
32	P20	Digital and Analog GPIO
33	Res	RST

Parameter

Chip Model	ASR5601
Operation Voltage	1.7~3.6V
Operation Frequency	2402 MHz    ～ 2480 MHz
Transmitting  Power	-20~7dBm
Receive Sensitivity	-97 dBm sensitivity (in 1 Mbps mode)
FLASH	512 KB
Quantity of GPIO	33
Module Size	15.2 mm (L) x 24.0 mm (H)
Packaging Type	SMT
Operating Temperature	-40    ℃ ~ + 85    ℃
Antenna Gain（ peak）	0 dBi

Antenna Information

1.  Antenna type
   TP 96 0B uses the onboard PCB antenna.
2. Antenna Interference Reduction
   To ensure optimal performance when the Bluetooth module uses the onboard PCB antenna, it is recommended that there be a space of at least 15 mm between the module antenna and other metal parts.

Packaging Information and Poduction Instructions

 Mechanical DimensionsProduction Instructions
Storage conditions of a delivered module are as follows:

1. The anti-moisture bag is placed in an environment where the temperature is under 40°C and the relative humidity is under 85%.
2. The shelf life of a dry-packaged product is six months from the date when the product is packaged and sealed.

Precautions:

1. Throughout the production process, each involved operator must wear an electrostatic ring.
2. During the operation, strictly protect the module from water and strains.

 Recommended Oven Temperature Profile

Refer to IPC/JEDEC standard; Peak Temperature: <250°C; Number of Times: 52 times 

Certification

Integration instructions for host product manufacturers according to KDB 996369 D03

Manual v01r01

 List of applicable FCC rules
CFR 47 FCC Part 15 Subpart C and Subpart C has been investigated. It is applicable to the modular transmitter

Specific Operational Use Conditions

• Antenna Placement Within the Host Platform
•  The module is tested for mobile RF exposure use condition..
• The transmitter module may not be co-located with any other transmitter or antenna.
• In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Limited Module Procedures

• Not applicable

Trace Antenna Designs
Not applicable

RF Exposure Considerations

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be mobile RF exposure use condition.

Antenna Type and Gain
The following antennas have been certified for use with this module. Only antennas of the same type with equal or lower gain may also be used with this module. Other types of antennas and/or higher gain antennas may require the additional authorization for operation.

 End Product Labelling Compliance Information
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:  “Contains FCC ID: 2AATP-TP960B”. The FCC ID can be used only when all FCC compliance requirements are met.

Information on Test Modes and Additional Testing Requirements
This transmitter is tested in mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirement, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

Additional testing, Part 15 Subpart B Disclaimer
This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rules requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed.

 Manual Information to The End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369.

OEM/Host Manufacturer Responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

 How to Make Changes – Important Note
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

FCC Statement

This device is intended only for OEM integrators under the following conditions:

1. The antenna must be installed such that 20 cm is maintained between the antenna and user.
2. The transmitter module may not be co-located with any other transmitter or antenna. Module Antenna Type: 2.4GHz onboard PCB Antenna, 0 dBi peak gain.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369.

The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369. OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body

Frequently Asked Questions

What is the recommended distance between the onboard PCB antenna and other metal parts?

To ensure optimal performance, it is recommended to maintain a space of at least 15 mm between the module antenna and other metal parts.

How can I establish a Bluetooth connection with the TP960B module?

To establish a Bluetooth connection, install the firmware, power the module, and pair it with your Bluetooth-enabled device following standard pairing procedures.

Documents / Resources

ECARE ELECTRONICS TP960B Bluetooth Module [pdf] Owner's Manual TP960B Bluetooth Module, TP960B, Bluetooth Module, Module

References

• User Manual