Quick guide
Equalizer
IMPORTANT
Read carefully before use. Keep for future reference.
You can find other languages, answers to frequently asked questions, and other useful information at easee. support.
Intended use
This product is intended for optimizing the power consumption by performing an automatic load balancing between the Easee Charging Robot(s) and the building. It avoids overload and power interruption while charging the electric vehicle (EV).
The product needs to be paired with a Charging Robot and connected to a compatible smart meter with the cable provided. In order for the Equalizer to work, the smart meter’s HAN port needs to be activated. The product may only be operated with the approved operating parameters and under the specified environmental conditions (see pages 5 and 9).
Uses other than those specified here are not permitted.
Product overview
Cable
Wall mounting kit
(for non-metallic surfaces)
Technical specifications
General
Product (mm): H: 110 x W: 110 x D: 27.5
Packaging (mm): H: 130 x W: 130 x D: 39
Operating temperature: -20 °C to +50 °C
Weight: 110 g
IP degree: IP40
Voltage: 12-32 Vdc 30mA
RJ11 connector
Installation
Cable length: 1.5 m RJ11 to R45 custom made cable Extended with an RJ45 adapter (up to 200 m)
Connectivity
Easy Link RF TM and WiFi*
HAN connection to energy meter Monitor power consumption with the Easee app RFID / NFC reader *WiFi is required for normal operation. When offline, it will continue to work via Easee Link RF TM
Charging Robot
Pairing
Before you start: make sure your Easee charger is connected to the same WiFi as you want the Equalizer to connect to. The Equalizer does not need to be connected to a power source during this step.
Hold the front side of the Equalizer over the light strip of the Easee charger and move it slowly downwards. When the charger lights green, the pairing is done!
Fuse box
Connecting
Plug the Equalizer into a HAN port
- Plug the Equalizer into a HAN port with the provided cable. After around 30 seconds, it should start flashing in white while connecting to your WiFi. Once connected, it is automatically added to the Easee app!
- Place the magnetic backside of the Equalizer directly on a metallic surface. If a metallic surface is not available, fix the metallic disc with a screw on the wall and then snap the Equalizer to it.
NOTICE! For better communication with the Easee charger, place the Equalizer outside of the fuse cabinet. When outdoors, it should be protected from the weather, e.g. inside the fuse box (see page 7).
In most cases the HAN port will be inactive – please contact your utility company to open it for 3rd party use.
What do the LED colors mean?
White, fast flashing – Booting
White, breathing every 10s – Normal operation
Red / white, switching – No WiFi added 2
Red/blue, switching – No internet connection
Red, flashing – No data from power meter 1
Red, breathing every 10s – Error 3
Touch the Easee logo in the middle to check power consumption:
Blue, fast flashing – High power consumption Blue, slow flashing – Low power consumption Count the flashes for a percentage – 1 flash (10%), 2 flashes (20%), up to 10 flashes (100%)
Hold the Easee logo for 3 seconds to check connectivity. You will see 2 flashes:
1st flash – Easee Link RF status
2nd flash – WiFi status
Green – Connected
Red – Not connected
Practical details
Charge faster
The Equalizer makes it possible to charge smarter, safer, and faster if the installation is scaled accordingly. To enable its true potential, the rated value of the charger’s circuit fuse should be as high as possible compared to the main fuse. Even in 1-phase setups, we recommend using a 3-phase cable to future-proof the installation.
Protection
The Equalizer is IP40. This means it has no protection against water. If placed outside the house, it must be installed inside a cabinet protected from the weather.
Product life cycle
This product requires no maintenance. If it needs to be repaired, please contact your Easee supplier.
Storage
The product should be stored in a tempered, dry, and well-ventilated area in order to preserve the packaging and its contents. Relative humidity should not exceed 80% and no corrosive gas should be present. Storage or transportation environment should never exceed the limits provided in the technical specifications (see page 5).
Disposal
This electronic equipment must not be disposed of in the household waste. For the return of old devices, free collection and acceptance points may be available in your vicinity. Observe local regulations for correct and environmentally friendly disposal.
Returns and complaints
Contact your distributor or Easee Customer Support at ease. support regarding the return and complaint of your product.
Contact details
Easee AS Professor Olav Hanssens vei 7A 4021 Stavanger, Norway Org. nr: 920 292 046
You can find additional contact details for your country at easee-international.com.
THIS DOCUMENT CONTAINS INFORMATION THAT IS SUBJECT TO CHANGE WITHOUT NOTICE.
The latest version of this publication can be downloaded at http://easee.support
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including, but not limited to, copying, recording, retrieving data, or computer networks without the written permission of Easee AS.
Ease and all other Easee product names and slogans are trademarks or registered trademarks of Easee AS. Easee products can be protected by one or more patents.
All other products and services mentioned may be trademarks or service marks of their respective owners.
Illustrations of the product and user interface are exemplary and may differ from the actual appearance.
December 2020 – Version 1.02 © 2020 by Easee AS. All rights reserved.
Easy AS
Professor Olav Hanssens vei 7A 4021 Stavanger, Norway
.easee-international.com
Documents / Resources
 |
easee Equalizer [pdf] User Guide easee, Equalizer |
