Home › Eachine › Eachine Moneagle User Manual

Eachine Moneagle User Manual

Features:

Built-in Dual module and dual system
With DVR function and DVR autonomous system
Built-in video input,Audio output
Built-in 5.8Ghz Dual diversity receiver automatically for best reception
4000mAh high-capacity battery for 3 hours working time
There are three video recording modes
Have the function of video replay
360-degree all-view HD display
Small, light weight, durable
5 Bands and total 8 Channels,40 frequency channel numbers
Built-in battery , easy to carry and outdoor use
Ultra-high luminance and button for controlling luminance
5-23 V wide supply voltage range, support 2-6S lipo battery to charge the monitor
A key to automatic signal search,Simple operation
Work status OSD display:Always be aware of the device working condition.

Operation Instructions

KEY
1. Power/MENU
  Press 3s boot, then press 3s shutdown
  Short press start to MENU
2. Search
  A key to automatic signal search, Simple operation
3. Rec
  Press the button, recording start, then press the button again to save the video
4. BAND+
5. 5 Bands
  Default mode, click the BAND+ option, A, B, E, R, F cycle selection
6. CH+
  Default mode, click the option for the CH1-8 cycles;
7. B+/B-
  Button for controlling luminance
JACK
1. AV: video input, Audio output
2. TF card: Support up to 64G
3. DC/5-23V:
  The monitor support DC5—23V wide voltage, it not only can be charged with USB and Power Bank, but also 2—6S lipo battery, which is very suitable for long—time flight.
Battery
Built—in 3.8V 4000mAh high—capacity polymer battery
DVR
*Enter DVR
Short press Power start to MENU, and press Power again to select DVR mode; So press CH+ botton to enter DVR mode. vGA/D1/HD three modes are available.
Parts list
*Host x 1
*USB charging cable x 1
*XT60 expanded charging line x 1
*Video line x 1
*Stick antenna x2
*Installed bracket x 1
*Instruction x 1

Technical parameter

Frequency Table(MHZ)

Eachine Moneagle User Manual – Download [optimized]
Eachine Moneagle User Manual – Download

References

User Manualmanual.tools

Published: March 25, 2021

Updated: April 24, 2021

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Joachim says:

September 9, 2021 at 7:11 pm
How can I set the date and time on the Eachine Moneagle?
Joachim asks How can I set the date and time on the Eachine Moneagle?

Manuals+ clarified question

Question

How can I set the date and time on the Eachine Moneagle?
Answer

To set the date and time on the Eachine Moneagle, you must access the device's internal menu system. Based on the manual, follow these steps:

Access the Menu: Short press the Power/MENU button to bring up the OSD menu.

Navigate to DVR Settings: Use the Power button to cycle through the menu options until you reach the DVR or System settings.

Enter Settings: Use the CH+ or Search buttons to navigate through the sub-menus. Look for an option labeled Date/Time or Date Stamp.

Adjust Values: Use the BAND+ and CH+ buttons to change the numerical values for the year, month, day, and time.

Save: Once adjusted, short press the Power/MENU button to exit and save your settings.

Note: If the date and time reset after powering off, ensure the internal 4000mAh battery is sufficiently charged, as it maintains these settings.
Read the full Q&A page
Reply
Mark Perrin says:

March 27, 2022 at 1:25 am
Same question, how can I set the time so the files I record don’t have a date stamp from the year 2068.
Thanks!
Mark
Mark Perrin asks Same question, how can I set the time so the files I record don't have a date stamp from the year 2068.
Thanks!
Mark

Manuals+ clarified question

Question

How do I set the date and time on the Eachine Moneagle to fix the DVR timestamp?
Answer

To set the date and time on the Eachine Moneagle, you must access the internal DVR menu system. Based on the manual instructions, follow these steps:

Enter the Menu: Short press the Power/MENU button to bring up the main menu.

Select DVR Mode: Press the Power button again to navigate to the DVR mode option, then press the CH+ button to enter the DVR sub-menu.

Navigate to Settings: Once inside the DVR interface, use the BAND+ or CH+ buttons to scroll through the settings until you find the Date/Time or Date Stamp option.

Adjust the Values: Use the navigation buttons to change the year, month, day, and time. Ensure you save the settings before exiting to prevent the timestamp from reverting to the default (2068).

Note: If the device does not retain the time after being powered off for a long period, the internal battery may be low, or the device may require a firmware check, as some early units had limited RTC (Real Time Clock) persistence.
Read the full Q&A page
Reply