E Plus E Elektronik EE600 Differential Pressure Sensor
Specifications
- Model: EE600 – Differential Pressure Sensor
- Analogue Outputs: 2-wire (15 – 35 V DC), 3-wire
- Electrical Connection: P15ow-e3r5sVupDpCly
- User Interface: LED Indication – Green LED Flashing, Red LED Flashing
- Mounting Examples Available
PLEASE NOTE
Find this document and further product information on our website at www.epluse.com/ee600.
Electrical Connection
WARNING: Incorrect installation, wiring or power supply may cause overheating and result in personal injury or property damage. Cables must not be under voltage during electrical installation and connection or disconnection, especially at terminal connections on circuit boards. For correct cabling, always observe the presented wiring diagram for the product version used. The manufacturer cannot be held responsible for personal injury or damage to property caused by incorrect handling, installation, wiring, power supply or maintenance of the device.
Analogue Outputs
Installation
Use a Ø7.5 mm drill to install the pressure connection nipples into the duct.
User Interface
LED Indication
| Green LED | Red LED | |||
| Flashing (1 s interval) | EE600 operates normally, the measured data is within the selected
measuring range |
Flashing (1 s interval) | The measured data is out of the selected range (overload or
reversed pressure connection) |
|
| One flash (2 s) | Confirms adjustment or return to
factory settings |
One flash (2 s) | Indicates the failure of the attempt to adjust zero point or span point, or to return to factory adjustment | |
| Off | No power supply or
electronics failure |
|||
| Fast flashing
(0.2 s interval) |
Auto-zero is executed
(first time 90 min after start / reset) |
|||
EE600 with 2-wire Analogue Output
- Measuring range: 100 % = max. / customised range, other MR of max. range
- No function
- Auto-zero version only
- These and further settings can be changed with PCS10 via USB configuration adapter (HA011066) while DIP switch S9 = 1
- Measuring range examples:
- S1 = 1, S2 = 0, S9 = 0, S10 = 1 0…750 Pa or 0…7 500 Pa
- S1 = 0, S2 = 0, S9 = 0, S10 = 0 ±1 000 Pa or ±10 000 Pa or customised measuring range
PLEASE NOTE
The 2-wire version allows manual zero-point adjustment at 90-minute intervals if an autozero valve is present.
EE600 with 3-wire Analogue Output
| S1 | S2 | MR1) | S3 | S4 | Time | S5 | S6 | Unit | S7 | DPB2) |
| 0 | 0 | 100 % | 0 | 0 | 50 ms | 0 | 0 | Pa | 0 | On |
| 1 | 0 | 75 % | 1 | 0 | 500 ms | 1 | 0 | mbar | 1 | Off |
| 0 | 1 | 50 % | 0 | 1 | 2 s | 0 | 1 | inch WC | ||
| 1 | 1 | 25 % | 1 | 1 | 4 s | 1 | 1 | kPa | ||
| S8 | Output | S9 | Setting3) | S10 | Measuring Direction4) |
| 0 | 0-10 V / 4-20 mA | 0 | DIP switches | 0 | Bidirectional |
| 1 | 0-5 V / 0-20 mA | 1 | PCS10 | 1 | Unidirectional |
- Measuring range: 100 % = max. / customised range, other MR of max. range
- Display backlight
- These and further settings can be changed with PCS10 via USB configuration adapter (HA011066) while DIP switch S9 = 1
- Measuring range examples:
- S1 = 1, S2 = 0, S9 = 0, S10 = 1 0…750 Pa or 0…7 500 Pa
- S1 = 0, S2 = 0, S9 = 0, S10 = 0 ±1 000 Pa or ±10 000 Pa or customised measuring range
E+E Elektronik Ges.m.b.H.
- Langwiesen 7 4209 Engerwitzdorf | Austria
- T +43 7235 605-0
- F +43 7235 605-8
- info@epluse.com
- www.epluse.com
QG_EE600 | Version v1.0 | 03-2025 | All rights reserved | 195408
FAQ
Q: How can I change the settings of the sensor?
A: Settings can be changed using DIP switches or PCS10 via USB configuration adapter while ensuring specific switch positions.
Q: What does the red LED flashing indicate?
A: The red LED flashing indicates that the measured data is out of the selected range or there is a failure in adjusting zero point or span point.
Q: How do I know if the sensor is operating normally?
A: The green LED flashing at specific intervals indicates normal operation and that the measured data is within the selected measuring range.
Documents / Resources
 |
E Plus E Elektronik EE600 Differential Pressure Sensor [pdf] User Guide EE600, EE600 Differential Pressure Sensor, Differential Pressure Sensor, Pressure Sensor, Sensor |