DZS 2428TE Wi-Fi 6 Ethernet Wireless Controller
Caution
Please follow the instructions below to avoid physical injury: You should not install the unit during a storm. Likewise, you should not connect or disconnect any line to avoid the risk of electric shock.
Caution & Warning
- This unit is indoor use and all the communication wiring are limited to inside of the building.
- DO NOT plug in, turn on or attempt to operate an obviously damaged unit.
- DO NOT use near water.
- DO NOT place near high high-temperature source.
- DO NOT disassemble the unit.
- DO NOT operate the unit in a location where the maximum ambient temperature exceeds 40°C.
- Open optical connections must use a protective cap under all circumstances to protect against physical damage and dirt.
- Before making connections, use isopropyl alcohol and non-fibrous cellulose to clean the faces of the connectors.
- Avoid impact stresses when handling connectors. Physical damage to the faces of optical connections impairs transmission quality (higher attenuation).
- Avoid a bend radius in excess of 30 mm for fiber optic links.
- Check the available voltage supply.
- Only use the unit in dry rooms.
- Set up the unit away from direct sunlight or other electrical equipment.
- Only connect approved accessories.
- It may only be repaired by authorized service personnel.
- This equipment is not suitable for use in locations where children are likely to be present.
Limited Warranty
- Not covered under this warranty is defect and damage resulting from product disassembly by yourself. And also, such behavior may amount to intellectual property infring
Introduction
Package Contents
- 2428TE
- QIG (Quick Installation Guide)
Specification
Information furnished by DZS is believed to be accurate and reliable. However, no responsibility is assumed by DZS for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of DZS. DZS reserves the rights to change specifications at any time without notice.
Interface
LED
Installation
- Attach the 2428TE to the desktop stand in the direction of the marked arrow.
- Connect the telco cable from POTS port to home phone lines.
- Connect the Ethernet cable from GE port to PC.
- Connect the power cable from power port to an electrical outlet.
- (OPTIONAL) Connect the Battery Backup Unit power and telemetry to the UPS port
Web Access
You can access the unit through a web browser by using the following steps:
- Connect an Ethernet cable from your computer to GE1 on the 2428TE.
- Launch a browser or telnet session and point it to 192.168.1.1.
- Enter the username and password.
The default username/password is admin/dzsi.
For security the password should be changed
Mounting on a Wall
If necessary, you may have your ONT mounted on a wall using mounting holes
FCC Statement
FCC Regulations:
This mobile router complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This mobile router has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Note
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
RF Exposure Information
This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm during normal operation.
ISED Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
CAN ICES-003 (B)/NMB-003(B)
This Class B digital apparatus complies with Canadian ICES-003.
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 20 cm during normal operation.
Frequently Asked Questions
- Q: Can I use this product outdoors?
- A: No, this product is designed for indoor use only.
- Q: How do I reset the unit to factory defaults?
- A: Press and hold the Reset button for 10 seconds to reset the unit to factory defaults.
- Q: What should I do if the unit is damaged?
- A: Do not attempt to operate a damaged unit. Contact authorized service personnel for repairs.
Documents / Resources
 |
DZS 2428TE Wi-Fi 6 Ethernet Wireless Controller [pdf] Installation Guide 2428TE, 2428TE Wi-Fi 6 Ethernet Wireless Controller, Wi-Fi 6 Ethernet Wireless Controller, 6 Ethernet Wireless Controller, Wireless Controller |