DYNAVIN D8-MOAGW MOST AGW Adapter

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -PRODUCT

Specifications

  • Compatible with: Mercedes SLK (R171 till ca. 03/2008 before Facelift Modell), E-Class W211 or S211, CLS (C 219)
  • Manufacturer: Dynavin GmbH
  • Country of Origin: Germany
  • Website: www.dynavin.de

OVERVIEW

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-1

  1. replace the original unit
  2. remove all connectors
  3. plug in the Most Adapter

PRODUCT INSTRUCTION

Canbus distributor within Mercedes SLK

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-2

Remove the screws from the panel on the driver’s side footwell with a torx screwdriver (2x T20/T25 Torx). One of the screws is placed in the middle, the other on the top. Carefully remove the plastic cap above the screw in the middle with a screwdriver or pocketknife. Pull out the side panel to the bottom left. It is anchored with other parts.

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-3Raise the carpet and unhook the lid from the black plastic channel. The lid is held with plastic hooks (marked).

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-4

Now you see the canbus distributor. Pull out the marked distributor to the top.

Canbus distributor within Mercedes MBE and CLS

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-5

Remove the two marked screws (T20/T25) to remove the panel under the glovebox. The canbus distributor is placed on the left side

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-6

 

The picture shows the original fiber optic cable.

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-7Pull out the MOST line from the original fibre optic cable.

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-8

After you disconnected the MOST line connect the fiber optic cable (without the most line) with this mating part.

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-9

Connect the pulled-out MOST line with this housing. After you‘ve done this connect it with the Most Adapter.

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-10

Place this cable on any free place within the canbus distributor. Where you can find the different canbus distributors is shown in pictures 2-5.

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-11

Connect the cable to the Dynavin unit as shown in the picture

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-12

Pull out the radio antenna from the AGW (black connector). Connect it with the extension cable from the delivery content and run the cable to radio.

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-13

FAQ

  • Q: What should I do if I encounter issues during installation?
  • A: If you face any difficulties or issues during installation, please refer to the provided manual for detailed instructions or reach out to our customer support at www.dynavin.de for assistance.

CONTACT

DYNAVIN-D8-MOAGW-MOST-AGW-Adapter -FIG-14

www.dynavin.de

© 2024 Dynavin GmbH

Documents / Resources

DYNAVIN D8-MOAGW MOST AGW Adapter [pdf] Installation Guide
D8-MOAGW, MOST AGW Adapter, MOST AGW, Adapter, D8-MOAGW MOST AGW Adapter, D8-MOAGW Adapter

References

Leave a comment

Your email address will not be published. Required fields are marked *