DURATECH LINK Mini Control Unit
Quick Setup & Use
- Open the device by unscrewing the 4 torx screws.
- Mount the unit to the wall using the screws provided in the packaging.
- Connect wiring to the corresponding connectors (RS485: 0.2–1 mm²; 230V: 1–4 mm²; 12V: 1–4 mm²; solid or stranded).
- Control options: use the OneTouch button (short press = ON/OFF toggle; long press >10 s = reset Bluetooth) or control via the DuraCloud app using Bluetooth (BLE).
- To set up in the app: open the DuraCloud app → Devices → find and tap your controller → Settings (select lamp model) → control from the dashboard.
INTRODUCTION
About LINK-MINI
- This swimming pool control cabinet is designed for the control of pool lights. During its development, a focus was placed on a clear and installer-friendly layout, with all connection points easily accessible and logically arranged.
- This simplifies cable installation and reduces the risk of wiring errors.
- The control cabinet is suitable for use in combination with our Duravision lighting. In addition, the cabinet is equipped with an RS485 connection for communication with external systems or DMX. The control cabinet can be connected to the Duracloud app.
- The app can be downloaded via QR code by scanning the sticker located on the side of the LINK-MINI as shown in the illustration below. This manual describes the operation, connections, and installation requirements of the control cabinet.
Inside the box
- LINK-MINI unit
- Screws and plugs
- Quickstart guide
TECHNICAL SPECIFICATIONS
| SPECIFICATIONS | LINK-MINI |
| Type of control DURAVISION | ON/OFF & Duranet |
| DURA Cloud App | YES |
| Bluetooth BLE | YES |
| Wi-Fi 2,4 Ghz | YES |
| Nominal input voltage | 230 VAC 50 Hz |
| Transformer VA rating | 60 VA |
| Output voltage (SELV) | 12 VAC SELV |
| IEC protection class | CLASS II |
| IP class | 54 |
| Unit dimensions (L*W*H) | 150*157*51 mm |
| Net weight | 1,2 kg |
| Ambient temp operating | 0-40 °C |
| CONNECTOR | MM² | WIRE |
| RS485 | 0,2-1 | solid & stranded |
| 230V | 1-4 | solid & stranded |
| 12V | 1-4 | solid & stranded |
INSTALLATION
- Open the device by unscrewing the 4 torx screws
- Mount to wall with the screws provided in the packaging.
Tools needed:
- Drill diameter 5,5 mm
- Drilling/screw machine
- Spirit level
- Pencil
- Torx bit
Cable connection
| CONNECTOR | MM² | WIRE |
| RS485 | 0,2-1 | solid & stranded |
| 230V | 1-4 | solid & stranded |
| 12V | 1-4 | solid & stranded |
ONE TOUCH CONTROL
You can control the swimming pool lamp controller in two ways:
- With the OneTouch button on the device
- With the DuraCloud app (Bluetooth / BLE)
OneTouch button (on the device)
- The touch button is located in the center of the LED ring.
- NO POWER
- LED WHITE ROTATING: BOOTING
- LED WHITE SOLID: IDLE
- LED GREEN ROTATING: ACTIVE
- LED RED BLINKING: ALARM
- BLUE TRIPLE BLINKING: BLUETOOTH RESET
- BLUE SOLID: BLUETOOTH CONNECTED TO APP
- Short press: Turn the lamps ON/OFF (toggle)
- Long press (more than 10 seconds): Reset the Bluetooth (BLE) connection
- Use this if the controller won’t connect to the app.
DuraCloud app (BLE)
The DuraCloud app lets you set up and control the controller using Bluetooth (BLE)
- Find your controller
- Open the DuraCloud app.
- Go to Devices.
- Find your controller in the list.
- Tap your controller to open it.
- Settings
- Open Settings in the upper right corner and select the lamp model.
- Open Settings in the upper right corner and select the lamp model.
- Control and configure
- From the dashboard, you can control the lamps and see the current status.
TROUBLESHOOTING
- Lamp does not react to color change requests via app
- Check if the correct lamp model is selected. Each DuraVision lamp has different features.
- Lamps are not synced (each lamp shows different color)
- Check lamp model
- Lamps supporting sync, sync via app
- Cannot detect device via bluetooth
- Check the color of led circle. If blue, the device is already connected to another app.
- Long-press the one-touch button to reset bluetooth connection.
- Check if bluetooth is enabled on the phone.
Contact details
- Propulsion Systems BV
- Dooren 72
- 1785 Merchtem, Belgium
- Tel +32 2 461 02 53
- Fax +32 2 706 59 60
- www.duratech.be
- info@duratech.be
- We reserve the right to change all or part of the contents of this document without prior notice.
Documents / Resources
 | LINK Mini Control Unit |
References
- duratech.bewww.duratech.be
- User Manualmanual.tools
Published: July 27, 2026