To power on the DT362DN, push and quickly release the Power
Button. The display will turn on after a few seconds. To put the
tablet in standby mode, push and quickly release the Power Button.
To power off for extended storage, use the software function to
shut down the computer.

Note: Use the AC-DC adapter to fully charge the
battery pack before first-time use. Push and quick release the
Power Button to put the tablet in standby mode when not in use to
conserve power.

Start Up

If the startup is successful, the appropriate interface will be
displayed after a few seconds. The wireless LAN connection may take
10-15 seconds to establish.

Wireless Networking

For information on wireless networking, refer to the tablet’s
manual for detailed setup instructions.

Data Capture Module Operation Guide

If your tablet includes a RFID Reader, follow the steps provided
in the manual to configure the settings for proper operation.

For More Support

Users can download additional operation guides from the DT
Research website for further assistance.

FAQ

Q: What should I do if the battery LED does not blink while
charging?

A: If the blue Battery LED does not blink while charging, unplug
and replug the AC-DC adapter to activate the charging process.
Repeat this process if necessary.

Q: How can I ensure safe operation of the tablet?

A: Follow all safety instructions provided in the manual, use
approved accessories, and avoid using the Power Button for extended
shutdowns.

View Fullscreen

Rugged Handheld Tablet

DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2022, DT Research, Inc. All Rights Reserved.

BOG0824 DT362DN ENG

DT362DN
INTRODUCTION
Thank you for acquiring the DT362DN, part of DT Research’s line of Rugged Tablets. Featuring a slim yet robust enclosure, the DT362DN with 6″ high brightness TFT display is powered by the Intel® Core® i3-N300 processor, offering optimal combinations of performance and power savings. The DT362DN is available with Microsoft® Windows® operating system. The software operating system features web browser, client/ server computing software, media player, accessories, and applications support.
PACKAGE CONTENTS
· One DT362DN · One Battery Pack · AC-DC Power Adapter · Basic Operation Guide
* The actual package contents may vary depending on the configuration acquired.

PRECAUTIONS
· Always exercise care when operating and handling the DT362DN
· Do not disassemble any portion of the DT362DN, as this will void any product warranty.
· Do not use any power adapter or charging cradle other than the one provided with the tablet or acquired from the manufacturer or its partners.
· In the unlikely event that abnormal noise, strange odor, or smoke is present, immediately power down the DT362DN and disconnect all power sources. Please report the problem to your device provider immediately.

The DT362DN

Input/ Output Ports A USB Type-C Port (power input)

Button Functions

BUTTON ACTION

Power Button

Trigger Buttons

Battery Latch

Data Capture Modules B USB Type-C C Smart Card Reader D Back Camera (optional) E Front Camera (Optional) F NFC/UHF RFID Reader (optional)

A
2

3
* The Handstrap and Digital Pen are optional.

OPERATION Powering ON and OFF
To activate DT362DN, push and quickly release the Power Button. The display will come on in a few seconds. To put the DT362DN in standby mode, push and quickly release the Power Button. To turn the DT362DN off for extended storage, power off safely using any software function that “shuts down computer” provided in the software operating system.
NOTE: The battery packs shipped with your tablet may be low in power – please use the AC-DC adapter with the DT362DN when setting up for the first time to fully charge the battery pack.
NOTE: To conserve power, push and quick release the Power Button to put the tablet in standby mode while not in use. Pushing briefly on the same button will wake up the system.
When the battery pack is charging, the blue-colored Battery LED should blink slowly. If plugging in the AC-DC adapter does not trigger this blinking activity and the LED stays dark, the battery pack(s) may have been drained substantially. Unplug/ replug the AC-DC adapter to the DT362DN a few times to activate the charging process.
NOTE: For DT362DN, avoid using the Power Button (“hold 4+ seconds” feature) to turn off the tablet–this form of hardware shutdown is intended to be a means of recovery from lockups, and not as normal operation.
3

Start Up
If the power up (from Standby mode or otherwise) is successful, the appropriate interface will be displayed after a launch sequence of several seconds. The wireless LAN connection may take 10-15 seconds to be established.
Wireless Networking
Wireless LAN The DT362DN is often delivered with an embedded (user-inaccessible) 802.11ac LAN adapter equipped with a hidden custom antenna. · Through the support of typical WLAN adapters, the DT362DN should be able to
detect all 802.11 access points in the vicinity for you to select the access point of your choice for connection. · The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT362DN and the access points have to match. The SSID is case-sensitive and it is recommended that you enable WEP/WPA/WPA2 encryption (or advanced alternatives) for secure access. · When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your networking equipment literature to properly configure associated settings such as Authentication mode, etc. · Refer to the access point operating manuals for setting up the 802.11 access points.
Data Capture Module Operation Guide
If your DT362DN comes with a RFID Reader refer to the steps below to configure the settings.
For More Support
Users can download the Tablet Modules Basic Operation Guides from the DT Research website.
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information Unique Identifier Trade Name: Model No.:DT362DN Responsible Party U.S. Contact Information DT Research, Inc. 2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com
4

Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
·Reorient or relocate the receiving antenna. ·Increase the separation between the equipment and receiver. ·Connect the equipment into an outlet on a circuit different from that to which
thereceiver is connected. ·Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the FCC. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body, with 0mm separation. FCC ID Label is in removable battery compartment, it could be easily found by removing the battery cover.
5

Safety Instructions
For Battery Safety: · Replace only with the same or equivalent type recommended by the manufac-
turer. Dispose of used batteries according to the manufacturer’s instructions. · Replacement of a battery with an incorrect type that can defeat a safeguard. · Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting
of a battery, that can result in an explosion. · (English)
CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type.
· (French)
ATTENTION: Risque d’explosion si la batterie est remplacée par un type incorrect.
For Protective earthing used as a safeguard: Ensure to connect the power cord to a socket-outlet with earthing connection if supplied by Class I power supply or power source.

Documents / Resources

DT Research DT362DN Rugged Handheld Tablet [pdf] User Guide
600-AX210D2, YE3600-AX210D2, YE3600AX210D2, DT362DN Rugged Handheld Tablet, DT362DN, Rugged Handheld Tablet, Handheld Tablet, Tablet

References

User Manual

DT Research DT362DN Rugged Handheld Tablet User Guide

DT362DN Rugged Handheld Tablet

Specifications

Product Information

Package Contents

Precautions

Product Usage Instructions

Powering ON and OFF