Dspread D50 Smart POS User Guide

This device is designed to comply with FCC emission limits for exposure to RF energy. The exposure standard is measured as SAR, with a recommended limit of 1.6W/kg averaged over one gram of tissue.

QUICK GUIDE

We recommend you read this guide to use your reader correctly and to make the most of it.

Code scanning

Your device supports bar codes and QR codes.

Launch the app
Put the QR code/bar code into the bar. Your device wil read the information automatical.

OVERVIEW

Welcome to D50

A) Use TypeC

B) Power Key
C) Volume Key

Specifications

Electrical characteriale

Power Supply

Input: 100-240∼50/60HZ 0.3A
Output: 5V2A

Device layout

Package contents

Be sure all items listed here were included with your device.

USING INSTRUCTION

Welcome to D50

How to take care of your reader

Keep & in environments with temperatures between 0°C and 40°C
Clean it using a dry cloth. Do not use water or other cleaning products.
Use the battery charger included with the reader. Do not connect it to a power source of more than 5 volts.
Avoid contact with microwaves or extreme heat sources such as hair dryers and stoves.
Do not submerge it in water or place & near sinks, bathrooms, de any other damp place.
Avoid exposing the battery in contact with metallic objects or to places that can generate short circuits or frost.
Do not use a sharp tool to sough or attempt to separate Internal components or connectors.
Do not drop, disari, mar, open, crush, or bend. warp, ort strod, paint, incinerate, or insert foreign objects into the reader.
Do not open & or try to fix it on your own. We can help you in case of a malfunction.
The reader contains small detachable parts and therefore should be kept away from children. If any of the small objects are accidentally swallowed, see a doctor immediately.

Operation of this equipment is subject to the following two conditions:

The equipment or device may not cause harmful interference.
The equipment or device must accept any interference received, including interference that may cause undesired operation.

FCC Regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference,
This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Radio Frequency (RF) Energy

This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. The exposure standard for wireless devices employing a unit of measurement is known as the Specific Absorption Rate, or SAR. The SAR limit recommended by the general public is 1.6W/kg, averaged over one gram of tissue by IEEE Std 1528. The FCC has granted an Equipment Authorisation for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirements. SAR compliance for body-worn operation is based on a separation distance of 10 mm between the unit and the human body. Carry this device at least 10 mm away from your body to ensure the RF exposure level is compliant or lower than the reported level.

FAQ

Q: What should I do if my device is causing interference?
- A: If your device is causing interference, try reorienting the antenna, increasing separation from other equipment, or consult a professional for assistance.
Q: Can I make modifications to the device?
- A: No, modifications not approved by the manufacturer may void your authority to operate the equipment.

Documents / Resources

Dspread D50 Smart POS [pdf] User Guide
2AGQ6-D50, 2AGQ6D50, d50, D50 Smart POS, D50, Smart POS, POS

References

User Manual

Dspread D50 Smart POS

Product Usage Instructions