DrayTek Corporation 35b Security Firewall User Guide

Q: What should I do if I encounter connectivity issues?
- A: If you experience connectivity problems, try reorienting the receiving antenna, increasing separation between devices, or seek assistance from a professional.
Q: Can I make modifications to the device?
- A: Any changes or modifications not approved by the manufacturer may void your authority to operate the equipment.

IMPORTANT SAFETY INSTRUCTIONS

Intellectual Property Rights (IPR) Information

Copyrights

© All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.

Trademarks

The following trademarks are used in this document:

Microsoft is a registered trademark of Microsoft Corp.
Windows 8,10, 11, and Explorer are trademarks of Microsoft Corp.

Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of their respective manufacturers.

Safety Instructions and Approval

Safety Instructions
- Read the installation guide thoroughly before you set up the router.
- The router is a complicated electronic unit that may be repaired only by authorized and qualified personnel. Do not try to open or repair the router yourself.
- Do not place the router in a damp or humid place, e.g. a bathroom.
- Do not stack the routers.
- The router should be used in a sheltered area, within a temperature range of +5 to +40 Celsius.
- Do not expose the router to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
- Do not deploy the cable for LAN connection outdoors to prevent electronic shock hazards.
- Do not power off the router when saving configurations or firmware upgrades. It may damage the data in a flash. Please disconnect the Internet connection on the router before powering it off when a TR069/ ACS server manages the router.
- Keep the package out of reach of children.
- When you want to dispose of the router, please follow local regulations on the conservation of the environment.

Warranty

We warrant to the original end-user (purchaser) that the router will be free from any defects in workmanship or materials for two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects that do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revisions or changes.

EU Declaration of Conformity

Hereby, DrayTek Corporation declares that the equipment type Vigor2865 complies with EU EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU.
The full text of the EU Declaration of Conformity is available at the following internet address: https://fw.draytek.com.tw/Vigor2865/Document/CE/.
Product name: VDSL2 Security Firewall
Model number: Vigor2865
Manufacturer: DrayTek Corp.
Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan.

Declaration of Conformity

Hereby, DrayTek Corporation declares that the equipment type Vigor2865 is in compliance with The Electromagnetic Compatibility Regulations 2016 (SI 2016 No.1091), The Electrical Equipment (Safety) Regulations 2016 (SI 2016 No.1101), and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (SI 2012 No. 3032).
The full text of the UKCA Declaration of Conformity is available at the following internet address: https://fw.draytek.com.tw/Vigor2865/Document/CE/.
Product name: VDSL2 Security Firewall
Model number: Vigor2865
Manufacturer: DrayTek Corp.
Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan

FCC

Regulatory Information

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device may accept any interference received, including interference that may cause undesired operation.

USA Local Representative	Company name	ABP International Inc.
	Address	13988 Diplomat Drive Suite 180 Dallas TX 75234
	ZIP Code	75234	E-mail	itadmin@abptech.com
	Contact Person	Mr. Henry N Castillo	Tel.	(972)831-1600 140

Caution:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

More updates, please visit www.draytek.com.

*The external power supply used for each product will be model-dependent.

Manufact urer

CWT

APD

MOSO

Address

No. 222, Sec. 2, Nankan Rd., Lujhu Township, Taoyuan County 338, Taiwan

No.5, Lane 83, Lung-Sou St., Taoyuan City 330, Taiwan

Shanghai Industrial Park, Guanwai Xiaobaim ang Songbai Road, Nanshan District, 518108 Shenzhen, Guangdong,

China

Shanghai Industrial Park, Guanwai Xiaobaim ang Songbai Road, Nanshan District, 518108 Shenzhen, Guangdong, China

Model identifier

2ABB012F UK

2ABB018F UK

2ABL024F UK

2ABL030F UK

2ABN036F UK

WA-12M1 2FG

WB-18D12 FG

WA-24Q12 FG

WA-36A12 FG

MS- V2000R12 0- 024Q0-GB

MSS- V2500WR 120- 030E0-GB

V30-V300 0R12 0-036T0- GB

2ABB012F EU

2ABB018F EU

2ABL024F EU

2ABL030F EU

2ABN036F EU

WA-12M1 2FK

WB-18D12 FK

WA-24Q12 FK

WA-36A12 FK

MS- V2000R12 0- 024Q0-DE

MSS- V2500WR 120- 030E0-DE

V30-V300 0R12 0-036T0-D E

Input voltage

100~240V

Input AC frequency

50/60Hz

Output voltage DC

12.0V

Output current

1.0A

1.5A

2.0A

2.5A

3.0A

1.0A

1.5A

2.0A

3.0A

2.0A

2.5A

3.0A

Output power

12.0W

18.0W

24.0W

30.0W

36.0W

12.0W

18.0W

24.0W

36.0W

24.0W

30.0W

36.0W

Average active efficiency

84.9%

86.2%

87.6%

87.8%

89.8%

83.7%

85.4%

88.6%

88.2%

87.8%

89.5%

89.3%

Efficiency at low load 10%

73.6%

78.0%

81.3%

83.3%

83.7%

74.5%

80.5%

86.4%

85.4%

84.7%

87.7%

No-load power consumption

0.07W

0.10W

0.07W

0.10W

0.08W

0.10W

External power supply (Power Adapter) information. For more updates, please visit www.draytek.com.

PACKAGE CONTENT

Take a look at the package content. If anything is missing or damaged, please contact DrayTek or the dealer immediately.
The type of power adapter depends on the country in which the router will be installed. * The maximum power consumption is 22 Watts.

PANEL EXPLANATION

LED	Status	Explanation
ACT	Off	The router is powered off.
ACT	Blinking	The router is powered on and running normally.
WAN2	On	The Internet connection is ready.
	Off	Internet connection is not ready.
	Blinking	The data is transmitted.
QoS	On	The QoS function is active.
QoS	Off	The QoS function is inactive.
USB1~2	On	The USB device is connected and ready for use.
	Off	No USB device is connected.
	Blinking	The data is transmitted.
DSL	On	The router is ready to access the Internet through a DSL link.
DSL	Blinking	Slowly: The DSL connection is ready. Quickly: The connection is training.
WCF	On	The Web Content Filter is active. (It is enabled from Firewall >> General Setup).
WCF	Off	WCF is disabled.
VPN	On	The VPN tunnel is active.
	Off	VPN services are disabled
	Blinking	Traffic is passing through a VPN tunnel.
DMZ	On	The DMZ function is enabled.
	Off	The DMZ function is disabled.
	Blinking	The data is transmitted.

LED on Connector

WAN2 / P6	Left LED	On	The port is connected.
		Off	The port is disconnected.
		Blinking	The data is transmitted.
	Right LED	On	The port is connected with 1000Mbps.
	Right LED	Off	The port is connected with 10/100Mbps.
LAN P1~P5	Left LED	On	The port is connected.
		Off	The port is disconnected.
		Blinking	The data is transmitted.
	Right LED	On	The port is connected with 1000Mbps.
	Right LED	Off	The port is connected with 10/100Mbps

The port “WAN2 / P6” is switchable. It can be used for LAN connection or WAN connection according to the settings configured in WUI.

Interface	Description
Factory Reset	Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink more rapidly than usual, release the button. Then the router will restart with the factory default configuration.
USB1~2	Connecter for a USB device (for 3G/4G USB Modem or printer or thermometer).
WAN2 / P6	Connecter for local network devices or modem for accessing the Internet.
LAN P1-P5	Connecters for local network devices.
DSL	Connecter for accessing the Internet.
PWR	Connecter for a power adapter.
ON/OFF	Power Switch.

HARDWARE

This section will guide you to install the router through a hardware connection and configure the router’s settings through a web browser. Before starting to configure the router, you have to connect your devices correctly.

NETWORK CONNECTION

Connect the DSL interface to the landline jack with a DSL line cable, or Connect the cable Modem/DSL Modem/Media Converter to the WAN port of the router with an Ethernet cable (RJ-45).

Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router and the other end of the cable (RJ-45) to the Ethernet port on your computer.
Connect one end of the power adapter to the router’s power port on the rear panel, and the other side into a wall outlet.
Power on the device by pressing down the power switch on the rear panel.

The system starts to initiate. After completing the system test, the ACT LED will light up and start blinking. (For detailed information on LED status, please refer to section 2. Panel Explanation)

WALL-MOUNTED INSTALLATION

Vigor router has keyhole-type mounting slots on the underside.

Drill two holes in the wall. The distance between the holes shall be 168mm.
Fit screws into the wall using the appropriate type of wall plug.
- Note The recommended drill diameter shall be 6.5mm (1/4”).

When you finished about procedure, the router has been mounted on the wall firmly.

SOFTWARE CONFIGURATION

To access the Internet, please finish the basic configuration after completing the hardware installation.

QUICK START WIZARD FOR NETWORK CONNECTIONS

The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. Make sure your PC connects to the router correctly.

Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1. For detailed information, please refer to – Trouble Shooting of the user’s guide.

Open a web browser on your PC and type http://192.168.1.1. A pop-up window will open to ask for a username and password. Please type “admin/admin” as the Username/Password and click Login.

Note If you fail to access the web configuration, please go to “Trouble Shooting” on the User’s Guide for detecting and solving your problem.

Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard.

If your router can be under an environment with high-speed NAT, the configuration provided here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is entering the login password. After typing the password, please click Next.

On the next page as shown below, please select the WAN interface that you use. If a DSL interface is used, please choose WAN1; if an Ethernet interface is used, please choose WAN2; if a 3G USB modem is used, please choose WAN5 or WAN6. Then click Next for the next step. WAN1, WAN2, WAN5, and WAN6 will bring up different configuration pages. Here, we take WAN1 (ADSL/VDSL2) as an example.

Click Next to go to the following page. You have to select the appropriate Internet access type according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. In addition, the field For ADSL Only will be available only when ADSL is detected. Then click Next for the next step.

PPPoE/PPPoA

Choose WAN1 as WAN Interface and click the Next button; you will get the following page.

After finishing the above settings, simply click Next.
Please manually enter the Username/Password provided by your ISP. Then click Next to view a summary of such a connection.
Click Finish. A page of Quick Start Wizard Setup is OK!!! will appear. Then, the system status of this protocol will be shown.

Now, you can enjoy surfing on the Internet.

MPoA/STATIC DYNAMIC IP

Choose WAN1 as WAN Interface and click the Next button; you will get the following page.

Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next to view a summary of such a connection.
Click Finish. A page of Quick Start Wizard Setup is OK!!! will appear. Then, the system status of this protocol will be shown.
Now, you can enjoy surfing on the Internet.

Customer Service

If the router cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.

Be a Registered Owner

Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com.

Firmware & Tools Updates

Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek website for more information on the newest firmware, tools, and documents. https://www.draytek.com.

ALVACO
- Telecomunicaciones
- Espana, S.L
- Avenida de Italia 10 Centro
- de Transportes de Coslada
- 28821 Coslada, Madrid,
Spain
- AntiPode
- 12 Rue des Chauffours
- 95000 Cergy – France
- BRINET sp. z o.o. sp.k.
- ul. Lubowska 23, 60-433
- Poznań

CMS
- UK – CMS Distribution
- Limited, 15 Worship Street,
- London, EC2A 2DT
- Ireland – CMS Distribution
- Limited, Bohola Road,
- Kiltimagh, Co Mayo, Ireland

Documents / Resources

DrayTek Corporation 35b Security Firewall [pdf] User Guide
35b Security Firewall, 35b, Security Firewall, Firewall

References

User Manual

DrayTek Corporation 35b Security Firewall

Specifications

FAQs

IMPORTANT SAFETY INSTRUCTIONS

Warranty

FCC

PACKAGE CONTENT

PANEL EXPLANATION

HARDWARE

SOFTWARE CONFIGURATION

Customer Service

Documents / Resources

References

Leave a comment

Cancel reply