DRAPER 19232 Engine Timing Kit
GENERAL PRODUCT INFORMATION
This product is designed to be used correctly and with care for the purpose for which it is intended. No liability is accepted by Draper Tools Limited for incorrect use or application of any of our products, and Draper Tools Limited cannot be held responsible for any damage to personnel, property or equipment when using this product. Incorrect use will also invalidate any warranty. The applications database and any instructional information provided has been designed to offer general guidance for a particular product’s use and while all attention is given to the accuracy of the data, no project should be attempted without referring first to the manufacturer’s technical documentation (workshop or instruction manual) or the use of a recognised authority such as Autodata. It is our policy to continually improve our products and thus we reserve the right to alter specifications and components without prior notice. It is the responsibility of the user to ensure the suitability of the product and information prior to use.
HEALTH AND SAFETY INFORMATION
GENERAL SAFETY INSTRUCTIONS
Warning: Please read all safety warnings and all details carefully. Failure to follow the warnings may result in serious injury or major component damage.
Important: Draper Tools recommends that this product should not be modified or used for any application other than that for which it was designed. Save all warnings and instructions for future reference.
Personal safety
- Stay alert, watch what you are doing and use common sense when using this product. Do not use this product while you are tired or under the influence of drugs, alcohol or any medication. A moment of inattention while using this product may result in serious personal injury.
- Use personal protective equipment as necessary.
- Check and remove any part of the product before turning/testing the engine. A part left attached to a rotating part of the engine may result in personal injury or major component damage.
- Carefully clean the tool components after every use.
- Keep the tool components safe and tidy.
- Do not use this product for any purpose other than for which it is designed.
Warning! Some of the packaging materials used may be harmful to children. Do not leave any of these materials in the reach of children. If any of the packaging is to be thrown away, make sure it is disposed of correctly; according to local regulations.
CONTENTS
| ITEM | DESCRIPTION | OEM | STOCK No. |
| A | High-Pressure Fuel Pump Tool Sprocket Locking | EN-51413-2 | 35697 |
| B | Auxiliary Drive Belt Tensioner Locking Pin | EN-955-2 | 35698 |
|
C |
Crankshaft Timing Tool |
EN-51412 |
35699 |
|
D |
Camshaft Locking Pin |
EN-51414 |
35700 |
|
E |
Flywheel Holding Tool For Automatic Transmission |
EN-51411 |
35701 |
APPLICATION
The 19232 has been developed as an engine timing kit for the vehicles listed below. Allows the user to lock the engine in the ‘timed’ position to allow the removal and replacement of the timing chain or for checking the engine timing.
Used on the following Vehicles:
- Vauxhall Cascada 2015 – 2017
- CDTi Vauxhall Insignia 2014 – 2017
- CDTi ecoFLEX Vauxhall Insignia Country Tourer 2014 – 2017
- Vauxhall Zafira-C Tourer 2014 – 2017
Engine Codes
2.0cc
LFS/B20DTH
PREPARATION
The following is for guidance only. Please refer to OEM derived data such as the vehicle manufacturer’s own data or Autodata. The use of this product is purely down to the user’s discretion and Draper Tools Limited cannot be held responsible for any damage caused what so ever.
PROCEDURE AND APPLICATION GUIDE
Depending on manufacture and model, some engine components do change. Please check with Autodata or the manufacturer’s data before use.
Instructions
Component A = High-pressure fuel pump sprocket locking tool (locking tool only) Use component A to lock the fuel pump sprocket in its timed position. 
Component B = Auxiliary drive belt tensioner tool
Component B is used to lock the auxiliary drive belt tensioner in it fully retracted position.
Components C = Crankshaft timing tool (3 parts)
Use component C to align and lock the crankshaft in its timed position.
Component D = Camshaft Locking pin
Use component D to lock the camshaft pulley in its timed position.
Component E = Crankshaft holding tool (automatic transmission)
Component E is used to lock and hold the flywheel from underneath the car to allow the crankshaft pulley bolt to be loosened and tightened.
Please note images are for guidance only and subject to change.
EXPLANATION OF SYMBOLS
Read the guide.
Refer to website.
GUARANTEE
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be free from defective materials and workmanship. Should the tool develop a fault, please return the complete tool to your nearest distributor or contact: Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: (023) 8049 4333 or: Product Helpline (023) 8049 4344.
A proof of purchase must be provided.
If upon inspection, it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out free of charge. This guarantee period covering parts/labour is 12 months from the date of purchase except where tools are hired out when the guarantee period is 90 days from the date of purchase. This guarantee does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless or unsafe handling, alterations, accidents, or repairs attempted or made by any personnel other than the authorised Draper warranty repair agent.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will be quoted and made accordingly. This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. Please note that this guarantee is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
CONTACTS
Draper Tools Limited, Hursley Road, Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF. U.K.
Helpline: (023) 8049 4344
Sales Desk: (023) 8049 4333
Internet: drapertools.com
E-mail: sales@drapertools.com
General Enquiries: (023) 8026 6355
Service/Warranty Repair Agent:
For after-sales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your local area.
Documents / Resources
![]() | 19232 Engine Timing Kit |
References
- User Manualmanual.tools
