Doorsafe DS1900 Wireless Intercom User Manual

1. Outdoor unit on battery
→ Open the flap on the
back of the outdoor unit and
insert the battery.
→ Insert the battery with
the rounded side (the head)
facing down.
→ The battery can be
charged with a USB-C
cable and 5V DC charger
at the bottom of the outdoor unit..

2. Outdoor unit on 5V DC
→ Remove the battery from
the outdoor unit.
→ Insert the supplied plug
with the 2 wires into the
back of the outdoor unit.
→ Connect to 5V DC direct
current. Connect red (+)
to red (+) and black (-) toblack (-).

INDOOR UNIT SUPPLIED WITH POWER

1. Insert the battery
→ Open the flap on the
back of the indoor unit and
insert the battery.
→ Insert the battery with
the rounded side (the head)
facing down.

2. Place in holder
→ Plug the supplied USB
cable into the back of the
holder and into a 5V DC
charger. This is the type of
charger that is also used for
a smartphone.
→ The red light on the
holder should light up.
→ Place the indoor unit in
the holder to charge the
battery.

MEANING OF FLASHING LED RING BUTTONS

→ Bell button or Key button flashes quickly when the battery is charging and stops flashing when the battery is charged.
→ Low battery: Bell button or handset button flashes during a call.

MOUNTING THE OUTDOOR UNIT

→ Attach the rain cover at shoulder height.
→ Stick with the double-sided tape.
→ Or screw with the 3 screws.
→ Secure the outdoor unit in the rain cover by tightening the small screw at the bottom of the outdoor unit.

CONNECT EXTRA INDOOR / OUTDOOR UNIT

1. Remove the battery from the outdoor unit.
2. Keep the push button on the outdoor unit pressed
while the battery is removed.
3. Put the battery back in with the button pressed: 2
tones will be heard and the button will flash.
4. Now press the button with the receiver on the
indoor unit until 2 tones are heard.
You will hear 2 tones again if the pairing is successful.
Repeat this for each additional indoor unit.
→ Do step 4 first and then steps 1, 2 and 3 to pair
an additional outdoor unit.
→ Press the bell or receiver button to stop pairing.

INDOOR UNIT OPERATION

1. Ring the doorbell
→ Press the button on the
outdoor unit to ring the
doorbell.
→ A ringtone will be heard
outside so that the caller
knows that the doorbell has
been successful. This tone
cannot be turned off.
2. Answer call
→ Press the button with the
receiver to answer the call
and talk back and forth. Press
the same button again to
disconnect.
→ Optional: Press the button
with the key to open the door.
3. Ringtone & Volume
→ Press the button with the
music note to change the
ringtone. There are 38.
→ Press the button with the
volume symbol to adjust the
volume of the ringtone. The
length of the ringtone is not adjustable.

AANSLUITSCHEMA DRAADLOZE UNLOCK MODULE

→ Wireless unlock module must be connected to 5-40V
DC or 9-40V AC power supply.
→ Wireless unlock module can be opened in three ways:
1. During a call, press the unlock button with the key on
the indoor unit.
2. Press the button on the wireless unlock module.
3. Press the button on the remote control.
→ Connect black (-) of the power supply to DC- of the
module and to port 1 of the door opener. Connect port 2
of the door opener to NO (operating current) or NC. Connect
red/black with white printed (+) to DC+ and to COM.
→ Pairing: Get power from module. Press button on module.
Connect power. Blue LED on module flashes. Press
unlock button during a call or button on remote control.
Press button on module to stop pairing.
→ Move pins to adjust unlock: 3 ,6, 8 sec.

TECHNICAL SPECIFICATIONS

→ Battery: 3,7V 18650 Li-ion, USB-C charging
→ Ringtones: 38, Volumes: 4
→ 433 Mhz Wireless signal
→ Total max outdoor/indoor stations: 5
→ Power: DC5V/1A; Consumption: <800uA
→ Casing: Plastic
→ Operating temperature: -10°C + 50°C
→ Water & dust restistant: IP55