DOMUS LINE RC3 Remote Controller Instruction Manual

DOMUS LOGO

DOMUS LINE RC3 Remote Controller Instruction Manual

DOMUS LINE RC3 Remote Controller

FIG 1 QR CODE

phone: 0039 0434 595911
fax: 0039 0434 923345
e-mail: info@domusline.com
website: www.domusline.com

Disposal icon The product must be disposed of separately from urban waste, delivering it to the collection centres established by the prevailing standard. Adequate sorted waste collection contributes to preventing negative effects on the environment and health and favours reuse and/or recycling materials. Incorrect disposal of the product implies the application of the administrative sanctions envisaged by the prevailing regulation.

FIG 2 Product Feature

 

Inserting – replacing batteries

FIG 3 Inserting - replacing batteries

 

Setting DIMMER mode operation

FIG 4 Setting DIMMER mode operation

 

Configuring with CALL-ME V17 receiver

FIG 5 Configuring with CALL-ME V17 receiver

 

Configuration with X-DRIVER

FIG 6 Configuration with X-DRIVER

 

FIG 7 Configuration with X-DRIVER

 

Setting TW mode operation

If the channel has already been set to dimmer / RGB mode, follow steps 1 and 2. If it has already been set in the TW channel, skip steps 1 and 2.

FIG 8 Setting TW mode operation

 

FIG 9 Setting TW mode operation

 

Configuring the MAGIC TUNE receiver

FIG 10 Configuring the MAGIC TUNE receiver

 

Configuring with TW X-DRIVER

FIG 11 Configuring with TW X-DRIVER

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

IC warning
This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

 

Documents / Resources

PDF thumbnailRC3 Remote Controller
Instruction Manual · RC3, Remote Controller, RC3 Remote Controller
PDF thumbnailRC3 Remote Controller
Instruction Manual · REMOTE3, 2AX76-REMOTE3, 2AX76REMOTE3, RC3 Remote Controller, RC3, Remote Controller

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. My rc3-tw remote controller has stopped working. I installed new batteries,but it still does not work. What can I do?

    🇺🇸 Anonymous asks My rc3-tw remote controller has stopped working. I installed new batteries,but it still does not work. What can I do?
    Manuals+ clarified question
    Question

    My RC3-TW remote controller has stopped working. I installed new batteries, but it still does not work. What can I do?

    Answer

    The manual for the DOMUS LINE RC3 remote controller provides instructions for inserting and replacing batteries (page 3). It states that the remote uses 2 x CR 2032 batteries. Since you've already replaced the batteries, here are some general troubleshooting steps you can try:

    • Check battery orientation: Double-check that the new CR 2032 batteries are inserted with the correct polarity.
    • Ensure proper contact: Make sure the batteries are seated firmly in their compartment and that the contacts are clean and free of debris.
    • Re-pair the remote: The manual includes sections on "Configuring with CALL-ME V17 receiver" (page 4) and "Configuring with X-DRIVER" (page 4), as well as "Configuring the MAGIC TUNE receiver" (page 7) and "Configuring with TW X-DRIVER" (page 7). Depending on your specific setup, you may need to re-pair your remote with its receiver. Follow the relevant configuration steps in the manual for your receiver type.
    • Test with another device (if possible): If you have another compatible device, try using the remote with it to determine if the issue is with the remote or the receiver.
    • Inspect for physical damage: Look for any visible damage to the remote controller.

    If these steps do not resolve the issue, you may need to contact Domus Line customer support for further assistance. Their contact information is available on page 1 of the manual and on their website.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.