DIHOOL IPS-S2 Motor Controller Instruction Manual

DIHOOL IPS-S2 Motor Controller

Product Usage Instructions

• Do not disassemble the product except by authorised personnel.
• Pay attention to Scene, IFTTT, or other settings when inching is enabled.
• When inching mode is enabled, the device will automatically turn off after being on for a while after each start.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

PRODUCT INTRODUCTION

IPS-S2 motor controller that integrates photoelectric signal/radio frequency/WIFI/ button control, mainly used to control electric linear actuators. The controller is compatible with a voltage of DC10V~30V, maximum current of 10A.
The positive and negative poles need to be wired according to the wiring diagram. If the positive and negative connections are not correct, it will not burn the controller. For example, a 60W linear actuator, please choose a 60-90W power adapter/switch power supply. If we use less power, the motor will not work. The controller can be used to control various specifications of electric linear actuators. WIFI module can be controlled through the “EWelink” APP, and only supports 2.4G WIFI. There are 6 buttons F1, F2, F3, on the controller for adjusting various functions. Please refer to the following for detailed instructions. The . The button controls the forward and backwards movement of the motor. Press ? to pair the WIFI.

MAIN TECHNICAL PARAMETERS

• Model: IPS-S2
• Input Voltage: DC 10V-30V
• Output Voltage: 20~93% Input Voltage Adjustable
• Current Monitoring Accuracy. #0.3A
• Maximum Current: 10A
• Power Consumption: < 3W
• DC Connector: 5.5*2.1MM
• RF Frequency: RF433MHz/2.4GHz
• WIFI Protocol: IEEE802.11 b/g/n
• Remote Control Battery. 23A 12V
• Working Temperature: -20°C ~ +70°C
• Working Humidity: 10%~90%RH(No condensation)
• Inout Sianal Tve: NPNI

DEFAULT ACCESSORIES

• Controller
• Remote Control (without battery)

OPTIONAL ACCESSORIES

• Limit Switch
• Magnetic Switch
• Photoelectric Switch
• Button Switch
• Handle Switch
• Foot Switch

FUNCTION DESCRIPTION

MATCH UP TO 8 REMOTE CONTROLS

• Remove the lid and find a small circuit board, see Figure 1
• Click the white matching button and the indicator light illuminates. Click any key of the remote control to match automatically. Press the up and down keys of the remote control to test.

Clear Pairing:

• Click the matching button 8 times, until the indicator light flashes and ends–unbind

FUNCTION F1: MOTOR PROTECTION SETTINGS

• Press and hold the F1 key for 3 seconds to enter the F1 sub-function settings, click F1 to switch in the sub-functions, And hold the F1 key for ? seconds to exit the settings (pre “to increase “ ” to adjust the value)

NOTE

First time connecting to wireless, it is necessary to place the controller within 5 meters of the router.
After connecting, the controller should be kept within 20 meters of the router

1. Download ‘Ewelink’ APP, register an ‘EWelink account and log in. (Connect to 2.4G WiFi. 5G Wifi not supported.)
2. Press ‘HOME’–‘ADD’–‘Quick Paring’–‘Add one device’
3. Enter the correct 2.4 GHz Wi-Fi account and password
4. After pressing the button for 5-20 seconds, the controller will automatically connect to the router
5. Tap”…” to enter Settings. Modify the device name and Channel 1 and Channel 2 (Figure 3).
6. Turn ON the ” Hide Al ON/OFF ” option. Enter ” Inching Settings” (Figure 4). In ” Inching Settings”, open ” UP” and ” DOWN”, and set both to ” 0.5sec ” (Figure 5).
7. Enter the F1 function of the controller and set the ” C” parameter to ” 0 ” (self-locking mode).

THE FOLLOWING PRODUCTS NEED TO BE PURCHASED SEPARATELY FOR REFERENCE ONLY
Paired With Photoelectric Switch: Signal And Wiring Instructions

• Brown Wire Connection with VCC (12V)
• Blue Wire Connection with GND
• Black Wire Connection with IN5

Signal Description:

• IN5: Refer To Function F2.
• IN5: low-level active

Functions Available:

1. When the photoelectric switch encounters a signal, the motor rises, but the signal disappears and the motor falls (automatic door opening/closing, smart trash can, etc.)
2. Switching the positive and negative poles of the motor, the photoelectric switch encounters a signal and the motor drops for 1-99 seconds, which can be adjusted (automatic production line)
3. The photoelectric switch encounters a signal that the motor rises, and after setting for 1-99 seconds, the motor descends (drone shutdown platform)
   More features await your discovery

Paired With Handle Switches Or Foot Pedals: Wiring Instructions

• Red Wire Connection with VCC
• Black Wire Connection with GND
• Blue Wire Connection with IN1
• Green Wire Connection with IN2

Signal Description:

• IN1: Motor Up
• IN2: Motor Down
• IN1, IN2: low-level active

• Yellow Wire Connection with GND
• Green Wire Connection with IN1
• Red Wire Connection with IN2

Signal Description:

• IN1: Motor Up
• IN2: Motor Down
• IN1, IN2: low-level active

Paired With Magnetic Switch: Signal And Wiring Instructions

• Brown Wire Connection with IN3 / IN4
• Blue Wire Connection with GND

Signal Description:

• IN3: Motor Down Limit
• IN4: Motor Up Limit
• IN3, IN4: low-level active

Functions Available:

• Attach the magnetic switch to the electric linear actuator (requires a built-in magnet) to enable ascent/descent at two desired positions.
• More features await your discovery

Paired With Emergency Stop Switch Or Button Switch: Signal And Wiring Instructions

• Brown Wire Connection with IN3 / IN 4
• Blue Wire Connection with GND

Signal Description:

• IN3: Motor Down Limit
• IN4: Motor Up Limit
• IN3, IN4: low-level active

Functions Available:

• Emergency shutdown of motor operation is possible
• More features await your discovery

Paired With Various Limit Switches: Signal And Wiring Instructions

• Brown Wire Connection with IN3 / IN4
• Blue Wire Connection with GND

Signal Description:

• IN3: Motor Down Limit
• IN4: Motor Up Limit
• IN3. IN4: low-level active

Functions Available:

• Fix the limit switches at two desired positions to enable the lift to ascend or descend to preset stops.
• More features await your discovery

Optional: IPS-S2B USB-C (PD3.1) Version Controller

Operating Voltage: 10~30V | Power Bank PD3.1 28V, PD3.0 20V
Operating Current: Max 10A
Functions:

1. Real-time current monitoring
2. Adjustable up/down overload current
3. Programmable run time
4. Obstacle rebound/pause
5. Soft start: gradual ascent/descent control
6. External interfaces: photoelectric/magnetic/limit switches, buttons, E-stop
7. Programmable auto-run
8. WiFi (Google Home / Alexa compatible)

Optional: IPS-S1 RS485 Industrial Controller

• Operating Voltage: 10~48V
• Operating Current: Max 10A

Functions:

1. RS-485 Serial Communication Control
2. PWM Speed Control
3. Real-time current monitoring
4. Adjustable up/down overload current
5. Programmable run time
6. Obstacle rebound/pause
7. Soft start: gradual ascent/descent control
8. External interfaces: photoelectric/magnetic/limit switches etc.
9. Programmable auto-run

Optional: IPS-S3 25 Amp High-Power Controller

• Operating Voltage: 10~30V
• Operating Current: Max 25A

Functions:

1. Real-time current monitoring
2. Adjustable up/down overload current
3. Programmable run time
4. Obstacle rebound/pause
5. Soft start: gradual ascent/descent control
6. External interfaces: photoelectric/magnetic/limit switches etc.
7. Programmable auto-run

WARRANTY CONDITIONS

Warranty

• 365 days from the date of purchase of the product

Warranty Regulations

1. Any damage to the equipment due to improper use will also result in the automatic termination of the warranty period.
2. Within 7 days of receiving the product, the damage caused by express transportation can be returned to Amazon for replacement. Or contact the DIHOOL seller for low-cost recycling.
3. Within 365 days of receiving the product, if there is any quality problem, you can contact us through the Amazon for a replacement.

FCC STATEMENT

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates and uses can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

AFTER SALES SERVICE

• Manufacturer: DIHAO ELECTRIC ZHEJIANG CO., LTD.
• ADD: Shanghai Industry, Liushi Town, Wenzhou City, Zhejiang Province, China
• E-mail: support@dihool.com
• Technical issues with the product can be reported through the above email address..

FAQ