DIGITUS DN-651130 4 Port Fast Ethernet Network Switch

Specifications

• Power Input: 12 to 48V DC redundant power
• Power Consumption: < 3 watts
• Network Protocols: IEEE802.3 10BASE-T; IEEE802.3i 10Base-T; IEEE802.3u;100Base-TX/FX;
• Industry Standard:
  FCC CFR47 Part 15,EN55022/CISPR22, Class A, IEC61000-4-2 (ESD): ±8kV (contact), ±12kV (air), IEC61000-4-3 (RS): 10V/m (80~1000MHz), IEC61000-4-4 (EFT): Power Port: ±4kV; Data Port: ±2kV, IEC61000-4-5 (Surge): Power rt: ±2kV/DM, ±4kV/CM; Data Port: ±2kV, IEC61000-4-6 (CS): 3V (10kHz-150kHz); 10V (150kHz-80MHz), IEC61000-4-16 (Common mode conduction): 30V (cont.), 300V (1s)
• Dimensions (W x D x H): 118 x 92.4 x 40 mm
• Weight: Product Weight: 0.48KG
• Working Environment: working temperature: -40～80℃ ;Storage temperature: -40～80℃
• Relative Humidity: 5%~95 % ( no condensation)
• Relative Humidity: 5%~95 % ( no condensation)
• Relative humidity: 5% to max. 95% (non-condensing)
• Number of ports: 4
• Ethernet speed: Fast Ethernet
• Industrial usage: yes
• Installation type: DIN rail
• Managed: no
• Number of ports (Uplink): 1
• Outdoorsuitable: no
• PoE (Power over Ethernet): no
• Protection against vanadlism: no
• Uplink port connection: SFP
• VLAN: no

Package contents

• 4+1 Port-Ethernet-Switch
• Manual

Product Usage Instructions

Industrial 4+1 Port Fast Ethernet Switch Unmanaged, 4 RJ45 Ports 10/100 Mbits
DN-651130 is a Industrial Fast-Ethernet-Switch with 4-Port 10/100Mbps RJ45 +1 Port 100Mbps base-FX. The industrial graded switch has the operating temperature of -40℃ ~ 80℃, has the super firmness can adapt to all kinds of harsh environment, can also be conveniently placed in the compact space of the control box. The installation characteristics of the guide rail, wide temperature operation, IP40 protection class housing and LED indicator light make the DN-651130 a plug and play industrial grade device, providing a reliable and convenient solution for users to network their Ethernet devices.

DN-651130 is a industrial graded 4+1 -Port Ethernet Switch, provides non-blocking wire-speed performance in harsh industrial environment.

• 4-port 10/100Base-Tx RJ45 with autonegotiation and auto-MDI/ MDI- X function
• 1-port 100Base-Fx interface SFP
• 12V to 48V DC, redundant power input
• -40℃ to 80℃ operating temperature
• IP40 aluminum housing
• Supports 6KV DC Ethernet ESD protection
• Supports 6KV DC EFT protection for power line
• Free Fall, Shock and Vibration Stability
• DIN-rail Installation
• Performance Specification: Bandwidth: 1.6Gbps, Packet Buffer Memory:1Mbit, Packet Forwarding Rate:1.2Mpps, MAC Address Table: 2K
• Flow Control: Back pressure for half duplex, IEEE 802.3x pause frame for full duplex
• LED Indicator: Power: Red, Fiber: Link 2(Green), Ethernet: Yellow.

Installation

1. Place the switch on a stable surface near power and network connections.
2. Connect the power adapter to the switch and plug it into a power outlet.
3. Connect devices to the RJ45 ports using Ethernet cables.
4. If using the SFP FE uplink, connect the corresponding SFP
   module and fiber optic cable.

Operation

The switch is plug-and-play and requires no configuration. Devices connected to the ports should automatically establish network connections.

Safety Notes

• This product is intended for indoor use only.
• Read all instructions and follow all warnings and instructions on the device.
• Do not place this appliance on an unstable surface (such as a trolley, stand, table, etc.).
• Do not use this appliance near water.
• Do not place this appliance near or above a radiator.
• The housing is equipped with openings for heat dissipation and ventilation. To prevent overheating during operation, the ventilation openings must not be blocked or covered.
• Do not place the appliance on a soft surface (e.g. bed, sofa, blanket, etc.). This will block the ventilation.
• The appliance must not be installed in a closed environment if adequate ventilation is not guaranteed.
• Do not spray any liquids onto the appliance.
• Disconnect the mains plug before cleaning. Do not use any liquid or foam cleaners.
• Clean the appliance with a damp cloth.
• Connect the device according to the power supply on the rating plate.
• To prevent damage to the appliance, it is important that all appliances are properly earthed.
• Do not place any objects on the power cable and lay it in such a way as to avoid tripping hazards.
• Use a surge protector, a regulator or an uninterruptible power supply (UPS) to protect your system from sudden, temporary and reduced power.
• Secure the system cable and mains cable properly and ensure that no objects are pressing on the cable.
• Do not insert any objects into the appliance through the openings in the housing. There is a risk of a short circuit, which can lead to fire or electric shock.
• Do not attempt to repair the appliance yourself. Always contact an authorized customer service centre.
• If any of the following conditions occur, unplug the appliance and send it to an authorized service centre for repair
• The mains cable, power supply unit or plug for the power supply is damaged or worn;
• Liquid has penetrated the appliance;
• The device has been exposed to rain or water;
• The device has been dropped or the housing has been damaged;
• The function of the device has obviously changed;
• The appliance cannot be operated as described in the operating instructions

Maintenance

Regularly check for dust accumulation and ensure proper ventilation around the switch for optimal performance.

www.digitus.info

FAQs

Documents / Resources

DIGITUS DN-651130 4 Port Fast Ethernet Network Switch [pdf] Instruction Manual DN-651130, DN-651130 4 Port Fast Ethernet Network Switch, 4 Port Fast Ethernet Network Switch, Fast Ethernet Network Switch, Ethernet Network Switch, Network Switch

References

• User Manual