DA-90453 Electrically Height Adjustable Table Frame
Specifications
- Maximum Load Capacity: Up to 120 kg
- Flexibly Adjustable Frame: Cross strut (112 –
165 cm) x longitudinal strut (130 – 180 cm) - Suitable for Tabletops: 120 – 180 cm x 140 –
200 cm and a depth of 55 – 75 cm - Height Adjustment Range: 72 – 120 cm
- Control Panel: LED display with 3 brightness
settings and memory function for 4 height settings - Motors: 3 motors for height adjustment,
lifting speed of 25 mm/sec, quiet operation (<55 dB) - Stability: Provided by 3 pedestals (58.5 cm
wide) with 2 footpads each for fine-tuning - Weight: 30 kg
- Shape: L-Shape
- Color: White
Product Usage Instructions
1. Assembly Instructions
Step 1: Install the feet by connecting them to
the lifting columns using screws and tighten with the allen
key.
Step 2: Connect the lifting column with
connection rods using screws and tighten with the allen key.
Step 3: Connect additional connection rods to
the lifting column and tighten them with the allen key. Insert two
connection rods accordingly.
Step 4: Attach the connection arm to the
connection rod using screws and tighten with the allen key.
Frequently Asked Questions (FAQ)
Q: Can the height adjustment be locked at a specific
level?
A: Yes, the control panel allows you to set and save up to 4
height settings for easy adjustment.
Q: Is it possible to install the longitudinal strut on either
side?
A: Yes, the third leg (longitudinal strut) can be fitted on the
right or left side of the frame for flexibility.
Q: How does the collision protection function work?
A: The G-sensor detects obstacles during height adjustment and
stops the motor in case of resistance, ensuring safety and
preventing damage.
Electrically Height-Adjustable Table Frame
Manual
DA-90453
1. Introduction
With this electrically height-adjustable table frame from DIGITUS® you can easily convert your desk into an ergonomic sit / stand workstation. Save the cost and hassle of finding a height-adjustable desktop and just use our electrically adjustable upgrade kit. This model can be used for tabletops with a length of 120-180 cm and 140-200 cm. Tabletop depths of 55 to 75 cm are recommended. Using the control panel, you can save 4 height positions and set them any time at the press of a button. The current height is shown on the LED display. Integrated collision protection prevents collision with any obstacles when raising or lowering the table.
2. Main Features
Maximum load capacity of up to 120 m Flexibly adjustable frame: Cross strut (112 – 165 cm) x longitudinal strut
(130 – 180 cm) Suitable for tabletops: 120 – 180 cm x 140 – 200 cm and a depth of
55 – 75 cm The longitudinal strut (3rd leg) can be fitted on the right Convenient, electrical height adjustment (without tabletop): 72 – 120 cm Control panel for height adjustment with LED display (3 brightness
settings) and memory function for 4 height settings Collision protection function (G-sensor) with 3 sensitivity levels – detection
of obstacles during upwards and downwards movement Automatic stop system – stops the motor in case of resistance and
automatically moves the frame back slightly 3 motors for easy and quiet (< 55 dB) height adjustment – Lifting speed
25 mm/sec. Stability is provided by the 3 pedestals (58.5 cm wide) with 2 footpads
each for fine-tuning to balance out any unevenness in the ground
3. Package Content
1x Electrically Height-Adjustable Table Frame 1x User Manual
2
4. Technical Data
Maxiumum load capacity
Flexibly adjustable frame
up to 120 kg
Cross strut (112 – 165 cm) x longitudinal strut (130 – 180 cm)
120 – 180 cm x 140 – 200 cm and a depth of Suitable for tabletops 55 – 75 cm
The longitudinal strut (3rd leg) can be flexible installed on the left or right
Convenient, electrical without tabletop 72 – 120 cm height adjustment
Automatic stop
stops the motor in case of resistance and
system
automatically moves the frame back slightly
Motors
3 motors for easy and quiet (< 55 dB) height adjustment – Lifting speed 25 mm/sec.
3 pedestals (58.5 cm wide) with 2 footpads each for
Pedestals
fine-tuning to balance out any unevenness in the
ground
Euro, plug (type C, CEE 7/16) Power supply cable C7, device socket, length: 2 m
Weight
30 kg
Shape
L-Shape
Color
White
3
5. Accessory List
Attention: The drawings below are for guidance only and they may differ slightly from the product and fittings received. Please contact our customer service department if you have any queries.
Image A
Specification M5 x 16 mm
Number 24+2
B
M6 x 11 mm
42+2
C
M8 x 12 mm
2+1
D
M5 x 16 mm
4+1
E
Allen Key
1
S = 5 mm
F
Cable Tie
6
G
Rubber Pad
16+2
4
H
Tablestop
2
Connector
I
Foot Pad
6
6. Component list
Part 1. Feet
No
Part
No
3 2. Lifting column
3
3. Side bracket
3 4. Connection arm
1
5. Connection rod
2 6. Connection rod
3
7. Connection rod
1 8. Connection rod
1
5
9. Connection rod
1 10. Handset
1
11. Control Box
1 12. Power plug
1
13. Adapter cable 1M
1 14. Adapter cable 1.3M 1
6
7. Assembly instruction
Step 1: Install the feet
Connect the feet (l) and the lifting column (2) with screws (B), and tighten them with the allen key (E). Step 2: Install the connection rod.
Using screws (B) to connect the lifting column with connection rods (5) and (6) and tighten them with the allen key (E).
7
Step 3: Install the connection rod.
Using screws (B) to connect the lifting column with connection rods (6) and (7) and tighten them with the allen key (E).
Insert two connection rods (6) into connection rods (5) and (7) respectively.
8
Step 4: Install the connection arm.
Connect the connection arm (4) to the connection rod (7) with screws (C) and tighten them with the allen key (E). Step 5: Install the connection rod
Connect connection rods (8) and (9) to the connection arm (4) with screws (B), and tighten them with the allen key (E).
9
Step 6: Install the connection rod.
Using screws (B) to connect the lifting column with connection rods (5) and (6) and tighten them with the allen key (E).
Insert the connection rod (6) into the connection rod (8). Insert the connection rod (9) into the connection rod (5).
10
Step 7: Fix the connection rod.
Adjust Tighten
Adjust the length according to the table size, then fix the frame with screws (B). Step 8: Install the side bracket.
Connect side brackets(3) to lifting columns(2) with screws(B), and tighten them with the allen key (E).
11
Step 9: Install the rubber pads. Step 10: Install the tabletop.
12
Step 11: Install the tabletop, control box.
13
Step 12: Connect cables and power plug.
Cable Management
Port for handset
Port for adapter cable
Port for cable connected to the lifting column
14
8. Common fault treatment
Adjust the desk upwards Adjust the desk downwards
Height Preset 1
Height Preset 2
Height Preset 3
Height Preset 4
To set Height Preset, press the M button until LED Display flashes then Preset 1, 2, 3 or 4 to program preset
Error Code Troubleshoot (Shown on LED Display) Hot Over-heating Alarms when continuously in motion for 2
protection minutes. Power back on and wait for at least 18 minutes before adjusting height again.
E10 Detection Alarms when motor sensor cannot be detected. alarm Turn off power, check the connection of motor and control box, and then power back on.
E20 Overload If alarm sounds when the desk is moving up, protection remove loads off the desk and try again. If it
15
E02 Rebound protection
E32 Overvoltage alar
E31 Undervoltage alarm
E60 Step out alarm
Breaking protection
alarms when desk is moving down, turn off the power, remove loads off the desk and re-try. Alarms when vibrated, collided or inclined during height adjustment. Check if there is anything in the way of desk motion. Then proceed to the reset the motor. It alarms when voltage is higher than anticipated value. Turn the power off, check the connection between power and control box. If no problem, power it back on. It alarms when voltage is lower than required value. Turn the power off, check the connection between power and control box. If no problem, power it back on. It alarms when height difference between left leg and right leg exceeds the set value. Power off first. Check whether the left leg and the right leg are in the same height. If not, re-do Installation Step 4 to make them same height. Power it back on. It stops and enters protection state when motor cables o r manual control cables are removed or disconnected accidentally; goes back to normal after it’s reconnected and alarm is cleared.
Engineering Mode
Change Displayed Unit (Un)
Press and hold the button until
“M” shows and flashes. Press “M” again and the display shows “Un”. Press to select. Press or to
switch between (metric) or
Change Brightness (br)
(imperial).
Press “M” to save your selection Press and hold the “M” button, until “S–“shows and flashes. Press
16
Collision Force Detection (CF) Reset
“M” again and the display shows “Un”. Press or to switch to “br”. Press “M” to select. Press or to switch between
Low (L), Normal (n) or High (H)
brightness. Press “M” to save your choice.
Press and hold the “M” button, until the “S–“shows and flashes. Press “M” again and the display shows “Un”. Press or to witch to “br”. Press “M” to select. Press or to switch between
“OFF”, Low (L), Normal (n) or Heavy (H) collision force
detection. Press “M” to save your choice. Press and Hold for 5 seconds, the LED display will show `RES’ and the desk goes down to the
lowest level and comes back to
certain height to finish Reset
process.
9. Important Safety & Usage Instructions
1. This appliance can be used by children aged from 8 years and above and persons with reduced physic, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved
2. Persons with reduced physical, mental abilities and or lack of experience and knowledge must not use the product, unless they’re under supervision, understand the hazards involved or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons
17
3. Children are forbidden to play on the product because of unforeseen actions when playing, so any dangerous consequences caused by this improper action will not be manufacturers. Children are forbidden to play with the appliance at all
4. Be familiar with all functions and program settings of the product before first use
5. Check carefully to ensure correct and complete assembly before using 6. Cleaning and user maintenance shall not be made by children without
supervision 7. If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent, or a similarly qualified person in order to avoid a hazard 8. Please make sure there is no hazard sources in your operating environment e.g., do not litter the tools around. Always be careful to treat the packaging materials to avoid any possible danger, e.g., plastic bag may lead to choking hazard to children 9. Keep the original package of the equipment, if necessary, in case of the future use in transportation 10. Power supply: AC 100 V 240 V, 50 / 60 Hz 11. Operating Temperature: 0 40°C 12. Unplug the power plug before cleaning, wipe the dust off the surface with a slight wet dishcloth, be careful do not let the drops into the internal parts and do not lose the connector 13. The electric box contains electronic components, metals plastics, wires etc., so dispose of it in accordance with each countries environmental legislation, not the general household waste 14. Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on the use of the equipment 15. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the cleaner used will not pollute the environment 16. This appliance shall only be used together with the included power supply unit. Every person who is responsible for this table at installation or employment of the table in daily use or in service and repair work should carefully read these instructions. Keep these instructions close to your sit/stand table 17. The table shall only be used as a working table with the possibility to continuously adjust working height between sitting and standing
18
position. The table shall only be used indoors and in dry premises (office environment or similar). 18. The table must not be overloaded maximum load is 120 kg 19. The motors may be run continuously for maximum 2 minutes. Afterward, the motors must stand by for approx. 18 minutes before they can be used again 20. Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury 21. Users should make sure that they never sit on the desktop in order to prevent serious bodily injury 22. Don’t clean the product with water while the power is still connected 23. Don’t disassemble or replace components while the power is still connected 24. Never operate the system with a damaged cord or plug 25. Never operate the system if it’s in moist environment or its electrical components have contact with liquid 26. Don’t operate thOvervoltage alarme system if the control box makes noise or odor. Alterations of the given power unit and control box aren’t allowed 27. Clear up all obstacles within the height adjustment range 28. Don’t leave the cords or plug unorganized in order to prevent tripping hazards 29. Any attempts to reconstruct the desk frame aren’t allowed 30. Don’t add anything to the adjustable junctions of the desk frame. 31. Outdoor use is prohibited 32. When the table is run up/down, keep the necessary safety distance to avoid the risk to get squeezed between the moving table top and fixed objects in the surrounding area. 33. When the table is run up/down the user shall keep watch so that nobody is injured or no object is damaged. The table top must not bump into a fixed object so that the table is overturned. Always remove any office chair before the table is run up/down 34. Alterations to the control box are absolutely forbidden 35. The table must not be used as a hoisting device for persons
19
Disclaimer
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
www.assmann.com Assmann Electronic GmbH Auf dem Schüffel 3 58513 Lüdenscheid Germany
20
Documents / Resources
 |
DIGITUS DA-90453 Electrically Height Adjustable Table Frame [pdf] Instruction Manual DA-90453, DA-90453 Electrically Height Adjustable Table Frame, Electrically Height Adjustable Table Frame, Height Adjustable Table Frame, Adjustable Table Frame, Table Frame |