df models 2406 Remote Control Instruction Manual

Remote Control

Insert the transmitter batteries: Open the battery compartment. Insert batteries (2x AA) (not included in the scope of delivery, DO NOT use rechargeable batteries!), ensure correct polarity! Close the battery compartment again. If the model is not to be used for a longer period of time, remove the batteries from the transmitter!

1. On/off switch (rear)
2. Steering wheel
3. Throttle lever
4. Sound on/off
5. LED indicator light
6. Battery compartment

Start Preparation

Your new RC model is ready to drive. Transmitter and receiver are bound. The speed controller is set up and ready to use. Charge the drive battery and insert it into the battery compartment in your RC model. To remove/insert the battery, open the battery compartment on the underside of the model. Connect the battery to the connector plug/speed controller (ensure correct polarity). Always switch on the remote control first and then the model (speed controller) (B ON/OFF). When switching off, proceed in reverse order. If the model is not being operated, ALWAYS disconnect the battery and remove it from the model! If the model slows down considerably or stops (no more drive, but steering works), stop driving immediately and recharge the battery (DO NOT switch on/off and continue driving, this will destroy the battery!).

Charging Battery

NEVER leave the charging cable unwound, this can lead to overheating!

The model is equipped with a Li-ion battery and a USB charger. ALWAYS charge the battery outside the model to avoid overheating during the charging process. NEVER charge the battery unattended (e.g., “overnight”), always use a fireproof base and observe the safety instructions for the battery/charger! When the model is not in use, the battery must ALWAYS be unplugged and removed from the model. Never pull on the cables; always pull on the plug to disconnect! Never charge warm/hot batteries; always allow them to cool down first!

• Connect the charging cable (USB) to a suitable power supply (USB power supply unit, output: 5 Volt – 10 Watt | not included).
• Now connect the battery to the USB charging cable.
• The LED flashes / lights up red, the battery is charging.
• The LED goes out when the battery is connected, the battery is fully charged.
• Disconnect the battery from the USB charging cable. Disconnect the USB power adapter from the power supply.
• Maximum charging time approx. 1-4 hours (depending on the output power of the USB power supply unit).

http://mali-racing.com/Anleitungen-Manuals/Akku_Sicherheitshinweise.pdf

When the model is not in use ALWAYS disconnect the battery and remove it from the model!

Driving
Turning the steering wheel to the left/right steers the model to the left/right. Pulling the throttle handle in the direction of the handle accelerates the model (moves forward). By pushing away from the handle, the model moves backwards. If the model does not move straight ahead without steering, you can adjust this using the trim on the underside of the model (adjust the trim lock (C) to the right or left).

Maintenance Regular Checks

The model is already assembled ready to drive and can be put into operation immediately after inserting the transmitter batteries (not included) and the drive battery. The drive and control components are assembled and wired, and the transmitter and receiver are connected automatically. However, you should check all screw connections for tightness before the first ride. Replace defective parts immediately and clean the model to remove dirt and dust.

Notice: The model is not designed for water travel. Water will get into the tires and destroy them. The electronics are also not waterproof and can be damaged. Very dusty and dirty terrain should also be avoided.

Check the following points regularly:

• Are the wheel nuts and screw connections tight?
• Is the servo control lever firmly seated on the servo shaft?
• Is the drive battery charged and fixed in the holder?
• Are the rotating and moving parts running smoothly?
• Are the cables routed and secured so that they do not get caught in moving parts?
• Is the range of the transmitter sufficient?

Declaration of Conformity

In accordance with the Radio Equipment Directive (RED) 2014/53/EU

• It is hereby declared that the product:
• MH664414 DF Jumbo Foot V2 Truck RTR | 9945 (EAN: 4250684199453) | 9948 (EAN: 4250684199484)
• When used as intended, complies with the essential requirements according to Article 3 and the other relevant provisions of Directive (RED) 2014/53/EU, EC EMC Directive 2014/30/EU, and 2009/48/EC.

Manufactured in accordance with the following harmonized standards:

• EN 62479:2010 ETSI EN 301 489-1 V2.2.3 (2019-11) | ETSI EN 301 489-3 V2.3.2 (2023-01) | ETSI EN 300 440 V2.1.1 (2017-03)
• EN IEC 55014-1:2021
• EN IEC 55014-2:2021 | EN IEC 62115:2020 Electric toys – safety
• EN IEC 62115:2020/A11:2020
• EN71:Part 1:2014+A1:2018 clauses 1-7
• EN71:Part 2:2020
• EN 71 PT.1-14:A1-18 MECHANICAL HAZARDS (1-7)
• EN 71 PT.2-20 FLAMMABILITY
• EN 71 PT.3-19:A1-21 HEAVY METALS CONTENT European RoHS Directive 2015/863/EU amending Annex II to Directive 2011/65/EU – Certain hazardous substances

European Parliament and Council Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) with its Amendment Directive (EU)2015/863 (on certain component)

• EIRP Power (Max.): 2405MHz-2475MHz | 6.29 dBm (4.26 mW)
• The source-based time-averaging power is below the max permitted sending level of 20 mW, and therefore the EUT is not required to conduct SAR measurement.
• Frequency Range: 2405-2475 MHz
• Signed for and on behalf of: DF Models – Jürgen Kamm – Drahthammerstr. 22 – 92224 Amberg – Germany – info@df-models.com Place, date: Amberg, 30.09.2025 Name: Jürgen Kamm (Inhaber)

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.