HOWT01F Outdoor Wi-Fi Pool Timer
“
Product Information
Specifications:
- Product Name: Outdoor Wi-Fi Pool Timer
- SKU: HOWT01F
- Model: V50517
- Input Voltage: 240VAC 60Hz
- Output Capacity: 40A Resistive, 240VAC 3HP, 240VAC
Product Usage Instructions:
Installation:
- Read Important Safety Information before beginning
installation. - Open the outer cover by pressing the clip.
- Remove the interior protection cover by unscrewing the two
screws holding it in place. - Select the knockouts to be used and remove the inner 1/2
knockout carefully. - Disconnect power at the circuit breaker and ensure power is off
before installing the Pool Timer. - Wiring must comply with national and local electrical code
requirements.
Connection to Wi-Fi:
- Refer to the Installation Instruction Sheet before proceeding
with Wi-Fi router connection. - Download the dewenwils App by scanning the QR Code or searching
dewenwils in Google Play or the App Store. - Launch the app and connect your Pool Timer to your network
(only supports 2.4GHz network). - If the Blue Wi-Fi LED indicator doesn’t flash initially, press
and hold the power button for 5-10 seconds. - If unable to connect to Wi-Fi, reset by long-pressing the power
button for 5-10 seconds.
Frequently Asked Questions (FAQ):
Q: What should I do if my Pool Timer can’t be connected to
Wi-Fi?
A: If the connection fails, try resetting the Pool Timer by
long-pressing the power button for 5-10 seconds. Ensure you are
connected to a 2.4GHz network and contact your ISP to disable the
5GHz network if needed.
Q: How do I know if my Pool Timer is powered on or off?
A: The Power Indicator being ON indicates that the Pool Timer is
powered on, while it being OFF means it is powered off.
Q: Can the Pool Timer control both Load1 and Load2
simultaneously?
A: Yes, the Pool Timer can control both loads simultaneously as
per the typical application wiring diagrams provided.
“`
Outdoor Wi-Fi Pool Timer
SKU:HOWT01F
V50517
WARNING: This Power Timer should be installed by a licensed
electrician.Turn power off at main panel before servicing this switch or the equipment it controls.
IMPORTANT: For outdoor use. Rain-tight or wet location conduit,
hubs, tubing, and cable fittings that comply with requirements of UL 514B must be used for installation.
Pool Timer.
Load Indicator Power Indicator Wi-Fi Antenna
Wi-Fi LED Indicator
Terminal Blocks Ground Terminal
Knockouts
PTW02 PTW04 Input: 240VAC 60Hz Output: 40A Resistive, 240VAC 3HP, 240VAC
1. Read Important Safety Information below before beginning installation. 2. Open outer cover by pressing the clip. 3. Remove the interior protection cover by removing the two screws holding
the cover in place (Figure 1). 4. Select the knockouts to be used. Remove the inner 1/2″ knockout by
inserting a screwdriver inthe slot and carefully punching the knockout loose. Remove slug. lf 3/4″ knockout is required,also remove the outer ring with pliers after removing the 1/2″ knockout. Smooth any rough edgeswith a file or sandpaper, if necessary. 5. Place and mark the Pool Timer in the desired mounting position. Install two screws at the mark and partially drive into place. Attach Pool Timer by placing screws over keyholes, then tighten screws. 6. Wire in accordance with national and local codes (see wiring diagrams below). Use copper wire AWG 8-18 suitable for 90°C(194°F).Tighten all connections to minimum 10.6 lb. in. torque. 7. Grounding:Connect all grounding wires to the grounding lug at the bottom of the enclosure. 8. Replace interior protection cover. 9. Close outer cover. Pool Timer now is ready to be connected to the WiFi router via the app.
WARNING: Risk of Fire or Electric Shock. Read instructions thoroughly before installation and preserve for future reference.
Disconnect power at circuit breaker and test if power is off before installing (or servicing) the Pool Timer (more than one circuit breaker or disconnect switch may be required to fully disconnect power).
Wiring must be in accordance with all national and local electrical code requirements. Inspect all terminals and wires with voltage meter before touching. The maximum total load to be controlled must not exceed Pool Timer capacity.
The Pool Timer enclosure does not provide grounding between conduit connectors. When metallic conduit is used, you must also i nstall grounding type bushings and in accordance with National Electrical Code (NEC) requirements.
POOL TIMER TYPICAL APPLICATION WIRING DIAGRAMS
Note: Pool Timer is only capable of being configured for 240VAC.
POOL TIMER Load1 Line1 Load2 Line2
Load
L1
Load
Power L1
Load L2
240VAC
Power L2
POOL TIMER
Load1 Line1 Load2 Line2
04
Please refer to INSTALLATION INSTRUCTION SHEET before proceeding with Wi-Fi router connection. Pool Timer must be installed before connecting to Wi-Fi router.
Software Installation Guide
Download the “dewenwils” App: Scan QR Code or search “dewenwils” in Google Play or the App Store to download and install the app. Note: All pictures shown are for illustration purpose only, the APP will be updated continuously, please refer to the latest APP interface to operate.
05
Each device can only be connected to one account. If anyone else needs to control it, please share your device via the app.
1.Launch the “dewenwils” app and connect your Pool Timer to your network. Note: The Pool Timer only support 2.4GHz network.
Power Indicator is ON Power Indicator is OFF Load Indicator is ON Load Indicator is OFF
Blue WiFi LED blinks
Blue WiFi LED blinks until stays on
Pool Timer is powered on Pool Timer is powered off Load is powered on Load is powered off
06
1) If the Blue Wi-Fi LED indicator on Pool Timer doesn’t flash at the first connection, please press and hold the power button for about 5-10 seconds to see if it starts flashing;
2) If the Pool Timer can’t be connected to WiFi, please long press power button for 5-10 seconds to reset;
3)The Pool Timer only work with 2.4GHz network. If your router broadcasts both 2.4GHz and 5GHz, please select the 2.4GHz network with the app. If connection still failed, we recommend you call your ISP and had them completely shut off the 5GHz network on the router. You are free to change the network to 5GHz again after connecting.
4) Please try to make the Pool Timer and router as close as possible.
1. Add the Pool Timer
Auto Add Mode (Bluetooth Mode) · Turn on the smartphone’s Bluetooth. · Open the “dewenwils” APP and click the “+” at the top right list, it will find the Pool Timer automatically. · If the Pool Timer is not automatically discovered, select Auto Scan to automatically search for the Pool Timer. · Follow the steps in the APP to complete the pairing.
07
Note:Please attention “location information” on mobile needs to be turned on.
2. Timer Function
Select the”Countdown”, “Schedule”, “Circulate”, “Random” or “Astronomical” to meet your needs.
Countdown Schedule
ON/OFF Button
Astronmical Random Circulate
Timer Function
08
1.Countdown: Tap “Countdown” to set the hours and minutes, and then tap the ” ” button. The Pool Timer will maintain the current state (on or off) until the end of the countdown. It will exit countdown mode automatically if you turn on/off manually.
2.Schedule:You can set the Start/End time in a 7-day period with a 1 minute interval according to your needs. Every program you set repeats weekly.
09
3.Circulate: You can set the duration of each ON and OFF, the Start and End time according to your needs. The ON/OFF schedule will repeat between the Start and End time. For example: You set a period from 9:00 to 15:00 on Monday to Friday, turn on your light for 1 hour , and off for 30 minutes. The outlet will repeat ON/OFF from 9:00 to 15:00.
4.Random: Either +/-30 minutes than setting ON/OFF time, randomly control device when you are away from home.
10
5.Astronomical: The controlled device will turn on or off at (before or after) sunset or sunrise.
Link dewensils account to Alexa 1. Open your Alexa app, tap “Skills” in the menu, and then search
“dewenwils” Select “dewenwils” and tap “ENABLE” to enable the dewenwils skills. 2. You will be directed to the account link page. Type in your “dewenwils” account and password, don’t forget to select your country/ region where your account belongs to. And then tap “Link Now” to link your dewenwils account. Control your smart devices Discover devices: Echo needs to discover your smart devices before controlling them.You say “Alexa. discover devices” to Echo. Echo will discover devices that have already been added in “dewenwils “app.You can also tap “discover devices” to discover the smart devices. Discovered devices will be shown in the list. Note : Every time you change the device’s name on the dewenwils app, Echo must re-discover before you control them. 1.Make sure the smart device has been added to the dewenwils App and the device is online. 2.Make sure the Google Home App is installed.
11
Start 1.Click Me in the bottom right corner, click Google Assistant, click Link with
Google Assistant. 2.The App will pull up the Google Home App, click Link. 3.Click agree Link. 4.Wait for it to finish loading, your smart devices will be synced to Google
Assistant or Google Home App that can control them. Next, you can assign rooms to your devices in the Google Home App.
dewenwils
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
12
13
ISEDC Warning:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil contient des émetteurs/récepteurs sans licence qui sont conformes aux RSS sans licence d’Innovation, Sciences et Développement économique Canada. L’exploitation est soumise aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d’interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences qui pourraient causer un fonctionnement indésirable de l’appareil.
ISED Radiation Exposure Statement: This equipment complies with ISED RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
Cet appareil est conforme aux limitesd’ exposition de rayonnement RF ISEDC établiespour un environnement non contrôlé. Cetémetteur ne doit pas être co-implanté oufonctionner en onjunction avec toute autreantenne ou transmetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.
Documents / Resources
 |
dewenwils HOWT01F Outdoor Wi-Fi Pool Timer [pdf] Instruction Manual HOWT01F, HOWT01F Outdoor Wi-Fi Pool Timer, Outdoor Wi-Fi Pool Timer, Wi-Fi Pool Timer, Pool Timer |