USER MANUAL
-MODEL NO:G6-

G6 Smart Lock

Please read this manual carefully before using the lock Please take good care of this manual for reference after reading

FCC ID: 2BL9C-G6
FCC ID: 2BL9C-G8
Unlock the Future with Our Smart Lock: Security Meets Convenience

FOR USERS IMPORTANT

Thank you for choosing DEVO smart lock
In order to ensure the ease of use and safety of our products, we have prepared this manual to help you better understand DEVO Smart Lock.
Thank you for purchasing a “DEVO” smart lock. Considering the continuous improvement and updating of our products, the actual products may be slightly different from the pictures in this manual, please refer to the actual products!
DEVO smart lock is popular among users for its unique appear-ance, advanced and reliable technology and considerate after-sales service. Our smart locks have been tested for reliability and functionality. Ambient light test, temperature test, etc. constitute the leading and unique advantages of smart locks.
Our company has established a complete intelligent R&D, manufacturing and sales system. All smart locks are independently developed by the company. We sincerely invite you to share with us your experience of use and opinions of improvement, which will help us to improve our products.

Hardware Introduction

(1) Overview

Notes: The “Emergency Power Supply Port” is not for battery charging purpose and can only be used for emergency power supply to the lock.

Compatible Doors

Compatible Doors

Parts List

Product Dimension

Installation Overview

*45-55mm door thickness use
*35-45mm door thickness use

Step 1. Install Deadbolt

1. Check your door to see if the deadbolt requires adjustment. If the backset is 70mm, turn the faceplate 180° to extend the length.
2. Insert and screw the deadbolt into the doorframe.

Step 2. Install Strike Plate

Step 3. Install Exterior Assembly
Remember to attach the rubber gasket to the handle before Installation.

1.  Measure your cross bore dimension and determine the installation steps accordingly
   If the cross bore of your door is 1 1½ /38mm”.
   please remove the adapter.
   • If the cross bore ofyour door is 2%””/54mm”. please keep the adapter.
2. Route the cable connected on the exterior assembly under the Latch. Make sure the tailpiece is Vertically to the exterior assembly bottom, as the illustration shows,

Step 4. Install Interior Assembly

1. Detach the back cover from the interior assembly.
2. Run the wires through the back cover.
   45-55mm door thickness use A
3. Secure the back cover with screws.
   Important: Please select Screw A, Screw B based on the thickness of the door(35mm-55mm)
   1. Thickness of Screw A compatible doors:45-55mm
   2. Thickness of Screw B compatible doors:35-45mm
   
   35-45mm door thickness use B
4. Tightly fasten the screws in place. Set the screws with your hands, then use a screwdriver to secure them.
5. Fix the exteriorassem blyby the doub le sided tape.
6. Wire to the interior assembly.
7. Mount the interior assembly. Make sure the wire is tucked into the cabin on the back of the interior assembly.
8. Check if the deadbolt retracts by turning the thumbturn.
9. Install 8 AA batteries into the door lock and it is ready to be used. (8 AA batteries are not included)
10. Pay attention to the placement direction of the positive and negative polles of the battery when installing it.

Apart from being able to configure your door lock through the app, you can also directly set the relevant settings on the door lock following the instructions below.

1. Smart Lock Powered on The smart lock self-checks the unlock ing direction when powered on. After the self-check is completed, the lock will be closed.

Programming Instructions

1. User Type
   

   Type	Capacity	Description
   Administrator	1	• Sequence ID 1 • Unlock • Management
   Regular User	199	• Sequence ID 2-200, • Unlock, (Invalid when the Anti-lock is On)
   Total	200	• Fingerprint Capacity: 100 • Passcode Capacity: 50 • IC Capacity: 50

2. Enter The Function Settings Mode Short press the “Settings” button. You will hear a voice prompt saying. “Please verify administrator user.” Enter the correct administra tor password, then press the “unlock” button to confirm. If the password verification is successful. you will enter the setting mode.
   Notes: When the automatic locking is turned on, the lock enters the unlocked state. After the set time, the lock will automatically close.
3. Setting Mode Function List
4. Restore Factory Settings 1. Press and hold the “Set” button. After 4 seconds, the lock will start to make a “dong” sound (7 times).
   2. Press and hold the button until you hear a voice prompt: To confirm, press the unlock button””
   3. Press the unlock button within 4 seconds and you will hear a voice prompt: Factory reset successful.
5. Set Administrator Password Step1: Press the setting button. If no adminis trator password has been set before, you will hear a voice prompt: Please set the administra tor password.
   Step2: After input the administrator password, press the unlock button to confirm
   Step3: Follow the voice prompt instructions. enter the administrator password again, and press the unlock button to confirm.
6. Others
   1. There are 5 consecutive trial and error opportunities for fingerprints and passwords within 5 minutes, and will be locked for one minute after exceeding the limit
   2. After the ultra-low power alarm, the motor cannot work. load condition If the battery power is lower than 10%, it will report low battery.
   3. Before configuring the network. please ensure that the power has just been disconnected and plugged in to avoid abnormal pre-operations that may cause the device to fail to enter the network configuration mode normally.
   4. After entering the network configuration mode, it will remains for 120s. If the network is not configured within the validity period of the network configuration the device will automatically restart and exit this mode. In this mode. no other operations are possible.

   Operation	Operation result	Indicator status	Voice broadcast
   Fingerprint/Password /Remote unlock / Wake up panel	Verify successfully	The green indicator light briefly lights up once	Verify successfully, Unlocked
   	verification failed	The red indicator light lights up briefly once	Verify successfully
   	Locked after exceeding the number of trial and error attempts	/	System locked
   	Battery is less than 25%	/	Low battery please replace the battery
   	Battery is about to run out	/	The battery is too low. please use the key or emergency power supply
   Lock	Successful	/	Locked
   Enter the menu	The button panel is fully illuminated	/	Please enter administrator password
   Invalid menu item	Repeat the current menu content	/	/
   Factory reset	Press and hold for 7s	Thee key panel is fully illuminated during the process.	7 sounds of “dong dong dong” Please press the unlock button to confirm
   Power on the device	Install the battery and turn on the power	The panel light tuirns on at the same time.	Power-on tone

7. App Operation Guidance
   1). Connect The Lock To Internet
   1 Following the installation instruction to install the smart lock. 2 Download Smart Life App. 3 Register and login to the Smart Life App. 4 Calibrate the smart lock and Complete Wi-Fi settings in the App.https://smartapp.tuya.com/tuyasmart
   2). Steps to Access System Networking
8. Main Interface Introduction
   1). Add Device (Smart Life App For Reference)
   Please make sure that your Phone is connected to the 2.4G Wi-Fi network Please make sure that your Phone’s Bluetooth is turned on
   1 Click Add Device’ 2 Waiting for device seach 3 Once the device is discovered click G3 device2). Network Configuration
   1 Device added sucessfully 2 Click Done 3 Choose the same 2.4G Wi-Fi network as your phone and enter you password 3).Members Management
   1 Member management2 Select the corresponding member3 Add or delete fingerprints and passwords4). Settings
   ① Enter the setting page ② Open the dormant switch ③ In sleep mode, the app does not support unlocking Notes: In sleep mode,the device cannot be woken up from the App and only be triggered from the device,which can greatly reduce the power consumption of the device.
   5). Password Settings 6). Device Unbinding

Troubleshooting

Product Parameters

(Add Random Digits Before Or After The Real Passcode) Random Digits No Length Limit

For any questions, please feel free to contact us, we will send you a reply and solve the problem within 24 hours.
Email: DEVO.services@outlook.com
DEVO reserves the final interpretation right of all terms and conditions in this manual.
MADE IN CHINA

FCC Warning
This device complies with part 15 of the FCC Rulles. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interferencereceived.including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for co mpliance couldvoid the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device.pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the eauipment into an outlet on a circuit different from that to which the receiver is connected.

Consullt the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontro lled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Documents / Resources

DEVO G6 Smart Lock [pdf] User Manual 2BL9C-G6, 2BL9CG6, G6 Smart Lock, G6, Smart Lock, Lock

References

• User Manual