DESLOC D120L Plus Series Fingerprint Smart Lock with Handle
[Number button]Number and letter switching function: for example, press the button [2] once to show “2”, , twice to show “A”, three times to “B”, and four times continuously to “C”;
[Enter button ]Cursor move function: Press the [Enter button] to move the cursor back, enter the subsequent text, and double-click the [Enter button] to confirm after the input is completed (as shown in the figure on the right);
[Menu button Backspace function
Press the [Menu button] button to backspace and delete if there is wrong unwanted text in the input process.
- [Numbe button]: Used to enter PIN, numbers, and names
- [Menu button]: Enter the settings interface, return, and backspace
- [el: Enter button, confirm the current operation, and press it to lock
- [A]: Up button, to scroll the menu item up
- [v]: Down button, to scroll the menu item down
Change Initial PIN
Step 1: Click the [Menu button] > Enter the initial PIN “123456” > Click the [Enter button] to confirm (The lock will automatically detect the the door’s opening direction. Please keep the door open and avoid any operations);
Step 2: Enter the administrator’s name, for example, to enter “Ab”: press the [2] button twice to select “A” > press the [Enter button] to confirm > then press the [2] button 3 times continuously to select “b” > double-click the [Enter button] to confirm;
Step 3: Enter a new PIN (6-8 digits), and press the [Enter button] to confirm.
p 4: Enter and confirm the new PIN again, and press the [Enter button to confirm. so that the new PIN settina is comoleted.
NOTE
- It is recommended that the thumb is preferred as the unlocking finger;
- For better fingerprints input, please remove debris and water on the fingerprint reader and fingers before input;
- If failure to enter fingerprint, the screen will display the prompt “Config fail” and automatically return to the home page of the menu, and the fingerprint shall be re-entered according to the steps shown in the figure.
- It is recommended not use the same finger as both the administrator’s fingerprint and the user’s fingerprint.
2.1 Add Admin FP
a. Add the fingerprint of an existing administrator
Step 1: Click the [Menu button] > select “Add Admin” > “Add Admin
FP”> “Select User”.
Step 2: Select an existing administrator; for example, select “Ab”, and
press the Enter button to confirm.
Step 3: Hold the fingerprint you want to enter on the “Fingerprint
Reader”,
“, short press it and then release, and repeat this operation 6
times until the “Config Successful” is prompted on the screen, so that
the fingerprint input is completed.a. Add the PIN code of a new user name
Step 1: Click the [Menu button] > select “Add User”> “Add User PIN”> “Add
User”;
Step 2: Enter the name of a new user, and press the [Enter button] to
confirm;
Step 3: Enter a new PIN (6-8 digits), and press the [Enter button] to
confirm;
Step 4: Enter and confirm the new PIN again, and press the [Enter button]
o confirm, so that the new PIN setting is completed.b. Add the PIN code of the existing user
Step 1: Click the [Menu button] > select “Add User”> “Add User PIN” >
“Add User”.
Step 2: Select the existing user, such as “Andy”, and press the [Enter
button] to confirm.
Step 3: Enter a new PIN (6-8 digits), and press the [Enter button] to
confirm.
Step 4: Enter and confirm the new PIN again, and press the [Enter
button]to confirm, so that the new PIN setting is completed.Step 1: Click the [Menu button] > select “Add User” > “Add Temp PIN”;
Step 2: Press the [Enter button] to confirm and get 4 sets of
temporary PIN (they can only be used once, and will be invalid after
use).To delete a single user, administrators and regular users, but unable
to delete primary administrator.
Click the [Menu button] > select “Del User” > “Del User” > select the user
name to be deleted such as “Andy” > click the [Enter button] to delete all
the information of the user.NOTE:
1. Function Definition: With this function enabled, the door lock will be kept in a
non-auto-locking state.
2. Quick enable mode: Resident users can enter the “5” through the keyboard to
enable the “Passage Mode” within 2 seconds after unlocking the door lock with their
fingerprint or Pin. After this Mode is enabled and the door lock is in the Sleep state,
he screen will light and display the “Passage Mode”.
3. Exit method: Users can enter the [Menu button and set the “Passage Mode” to “OFF”;
or enter “5” through the keyboard within 2 seconds after unlocking the door lock with
一
their fingerprint or Pin to exit this mode.
b. Auto Lock
Step 1: Click the [Menu button] > select “Lock Settings” > “Lock Setup” > “Auto Lock”;
Step 2: Click the [Enter button] to select, enter the period during which the lock is
automatically closed (the period time can be set to 5~120s), and click the [Enter
button] to confirm.
Documents / Resources
 |
DESLOC D120L Plus Series Fingerprint Smart Lock with Handle [pdf] User Guide D120L Plus Series, D120L Plus Series Fingerprint Smart Lock with Handle, Fingerprint Smart Lock with Handle, Smart Lock with Handle, Handle |