deli T313 Split Comb Binding Machine
Overview
Model T313 Deli comb binding machine is designed for punching paper and plastic sheets, and using a plastic clip with a rubber ring for loose-leaf document binding. Read this manual to ensure correct use and higher binding efficiency.
Specifications
| Parameter | Value |
|---|---|
| Model | T313 |
| Maximum punching thickness | 20 sheets of paper (80g A4 paper) |
| Binding edge distance | 2–5 mm |
| Hole size and pitch | 3 mm × 8 mm, 14.3 mm pitch |
| Binding specification | A4 size paper or smaller |
| Maximum binding thickness | 450 sheets |
| Net weight | 6.35 kg |
| Device dimensions | 405 mm × 315 mm × 380 mm |
- Consumable comb thickness recommendations (mm → sheets): 620→22180; 840→25210; 1060→28240; 1280→32280; 1410→35350; 16120→38360; 18140→45400; 20160→51450.
Quick Setup & Use
- Before punching original materials, test with waste paper to confirm the machine works normally.
- Set punching position: Set the locating block to the desired position. Loosen by turning the knob counterclockwise, then fasten by turning it clockwise.
- Set edge margin: Turn the punching margin control to set the edge margin.
- Punching: If punching an odd-sized document, pull out and disengage the proper punch selector. Insert paper into the punching channel, pull the handle all the way down until it stops to punch completely through, then pull the handle up and remove the punched paper.
- Empty waste container: Empty the paper scrap box periodically.
- Binding: Place the rubber ring behind the comb-shaped plate and move it left with the opening facing upward. Rotate the pull ring handle clockwise to open the rubber ring, then put the punched file onto the rubber ring. Rotate the pull ring handle counterclockwise to remove the file.
Product Structure & Components
- Handle
- Comb plate
- Pull ring plate
- Pull selector
- 5Locating block
- Pull ring handle
- Punching margin control
- Paper scrap box
Consumable Specification Recommendations
| Comb (mm) | Sheets | Comb (mm) | Sheets |
|---|---|---|---|
| 6 | 20 | 22 | 180 |
| 8 | 40 | 25 | 210 |
| 10 | 60 | 28 | 240 |
| 12 | 80 | 32 | 280 |
| 14 | 100 | 35 | 350 |
| 16 | 120 | 38 | 360 |
| 18 | 140 | 45 | 400 |
| 20 | 160 | 51 | 450 |
Directions for Use
- The machine is used for punching of paper and plastic sheet, and plastic clip is used for loose-leaf binding. The machine only can be used for this purpose, and please use it according to the operation instruction.
- Before punching of the original materials, do remember to use waste paper to test whether the machine works normally.
- Empty the waste container periodically.
- The upper limit number for punching is 20, and this number shall not be exceeded.
Punching Steps
- Set the locating block at the desired position. Turn the knob counterclockwise to loosen. Turn it clockwise to fasten.
- Turn the punching margin control to set the edge margin.
- Pull out and disengage the proper punch selector when punching odd-sized documents.
- Push paper into the punching channel. Pull the handle all the way down until it stops to punch completely through. Pull the handle up completely and remove the punched paper.
Binding Steps
- Place the rubber ring behind the comb-shaped plate and move the rubber ring to the left with the opening facing upwards.
- Rotate the pull ring handle clockwise to open the rubber ring and then put the punched file onto the rubber ring.
- Rotate the pull ring handle counterclockwise to remove the file.
Troubleshooting and Common Fault Analysis
| Fault Phenomenon | Fault Cause Analysis | Troubleshooting Method |
|---|---|---|
| It is hard to press the handle when punching paper. | There is paper scrap or another foreign object in the paper cutting area. | Take out the debris with chipboard. |
| The operating load is beyond the recommended punching capacity. | Operate according to the limits described in the instructions. | |
| The punching edge distance has an uneven inclination. | The two sides of the incoming paper are unbalanced/misaligned. | Align both sides of the paper evenly. |
| There is paper scrap or another foreign object in the paper cutting area. | Take out the debris with chipboard. | |
| The open rubber ring displays uneven alignment. | The comb plate has deformation caused by a collision. | Straighten the comb plate using a straightedge or ruler. |
| The draw hook of the pull ring plate is deformed. | Calibrate and adjust the draw hook by hand. | |
| Incomplete paper punching or the paper is difficult to extract. | The number of sheets being punched at one time is too large. | Reduce the punching thickness per pass, adhering to the instruction limits. |
| The paper cannot reach the bottom of the slot. | The paper is damaged or the edge is curling. | Smoothen the paper edges and try again. |
Product Parameters
- Maximum punching thickness: 20 sheets of paper (80g A4 paper)
- Binding edge distance: 2-5 mm
- Hole Size and Pitch: 3mm × 8mm, 14.3mm pitch
- Binding specification: A4 size paper or smaller
- Maximum binding thickness: 450 sheets
- Net Weight: 6.35 kg
- Device Dimensions: 405 mm × 315 mm × 380 mm
Warranty Card
Thank you for purchasing our products. The interests of customers who purchase our products will be protected. For any malfunction due to product manufacturer quality issues, please contact authorized local dealers or service centers with this receipt and the warranty card.
Warranty Terms:
- For product failures occurring under normal operating circumstances, free of charge repair and spare parts replacement services shall be provided by our company within one year commencing from the date of purchase.
- Customers are required to present this warranty card and the original purchase invoice to our company upon requesting warranty service. This warranty card shall be valid only after the following form is filled out in detail and affixed with the official seal of the dealer.
- No free of charge repair service shall be provided in the event of any of the following circumstances:
- Expiration of the warranty period;
- Damages caused by improper use, maintenance, or storage not in accordance with the requirements of the user manual;
- Failure or damage resulting from unauthorized disassembly, repair, or modification;
- Failure or damage caused by force majeure;
- Wear parts or consumable accessories.
This warranty card is delivered with the product (one card per product). Please keep this warranty card in a secure place to claim free warranty service. It will not be replaced if lost.
Warranty Registration RecordsDate of Purchase: ______ Year ______ Month ______ Day
| Product Information | Product Name | Serial Number | ||
| Product Model Number | T313 | Manufacturing Date | ||
| Customer Information | Company Name | |||
| Address | Contact | |||
| Sales Information | Dealer Name | Phone | ||
| Address | Contact | |||
| Maintenance Record | Date of Purchase | Phone | ||
| Description of Malfunction | Maintenance Results | Customer Signature | Technician Signature | Maintenance Date |
(Dealer Copy: This copy shall be cut along the dotted line and retained by the dealer.)
| Product Information | Product Name | Serial Number | ||
| Product Model Number | T313 | Manufacturing Date | ||
| Customer Information | Company Name | |||
| Address | Contact | |||
| Sales Information | Dealer Name | Phone | ||
| Address | Contact | |||
| Maintenance Record | Date of Purchase | Phone | ||
| Description of Malfunction | Maintenance Results | Customer Signature | Technician Signature | Maintenance Date |
Troubleshooting
| Fault Phenomenon | Likely Cause | Troubleshooting Method |
|---|---|---|
| Hard to press the handle when punching paper | Paper scrap or another foreign object in the paper cutting area | Take out the debris with chipboard. |
| Hard to press the handle when punching paper | Operating load beyond the recommended punching capacity | Operate according to the limits described in the instructions. |
| Punching edge distance uneven inclination | Incoming paper sides unbalanced/misaligned | Align both sides of the paper evenly. |
| Punching edge distance uneven inclination | Paper scrap or foreign object in the paper cutting area | Take out the debris with chipboard. |
| Open rubber ring shows uneven alignment | Comb plate deformation from collision | Straighten the comb plate using a straightedge or ruler. |
| Open rubber ring shows uneven alignment | Draw hook of the pull ring plate deformed | Calibrate and adjust the draw hook by hand. |
| Incomplete paper punching or paper difficult to extract | Number of sheets being punched at one time too large | Reduce the punching thickness per pass, adhering to instruction limits. |
| Paper cannot reach the bottom of the slot | Paper damaged or edge curling | Smoothen paper edges and try again. |
MORE INFORMATION
- DELI GROUP CO., LTD. 301 Xuxiake Ave. Ninghai County Ningbo 315600 China Made in China
- info@nbdeli.com
- www.deliworld.com
- 22) PAP Reserved For Use Version: 1.0Date: 5-2025
Documents / Resources
 | T313 Split Comb Binding Machine |
References
- User Manualmanual.tools
Published: July 24, 2026