DECKED YF3 Drawer System

YF1/YF3 US FORD RANGER (2019-2023) 5’1” BED LENGTH FORD/MAZDA RANGER – XL DUAL/BT50 DUAL (2011-2022) 60.98”/1549MM BED LENGTH
- Trust us on this one; don’t go commando and attempt your install without reading. You’ll just cuss a bunch and create even more chaos in your truck bed.
DANGER: RISK OF SERIOUS INJURY OR DEATH
Failure to follow these instructions, or any unauthorized modification/misuse of this product, can result in property damage, severe injury, or death.
Prohibited Uses & Warranty Void
- No Hazardous Materials: Do NOT place fuels, flammables, explosives, or hazardous materials inside or on top of any DECKED product.
- No Unauthorized Modifications: Any modification or unintended use of this product immediately voids all warranties.
Weight Limits & Payload Distribution
Distribute Loads Evenly: Concentrated weight will damage the system. All loads must be evenly distributed.
Maximum Payload Capacities
- Top Deck: 1000 lbs/454 kg maximum capacity
- Tray: 400 lbs/181 kg maximum capacity Concentrated weight can damage the drawer system. All loads must be evenly distributed to approximately 50 lbs per foot2.
- Vehicle Limits: Always check your vehicle owner’s manual for its maximum payload capacity; do not exceed vehicle limits.
Installation & Maintenance
- Follow Instructions: The DECKED Drawer System must be properly installed and anchored exactly as outlined in the instructions.
- Use Provided Hardware: If supplied, you must use the DECKED tie-down brackets instead of the SUV’s original factory brackets.
- Clear the Cargo Area: Before installation, remove any items from the vehicle’s cargo area that might be blocked by the system.
- Routine Inspections: Check all fasteners at least every three months and retighten any that have come loose.
Vehicle Operation & Safety
- Secure the Liftgate: The vehicle’s liftgate must be closed and latched whenever the vehicle is in motion.
- Wear PPE: Eye protection is required during installation and maintenance.
HEY! TORQUE BOY READ BEFORE YOU INSTALL
Welcome to DECKED. Bad instructions, useless advice, and sketchy internet forums end here. We’re here to make sure your install goes off without a hitch—saving you time, headache, and heartburn. Your only job? Actually read the instructions and follow the steps in order.
Tools & Pre-Install Prep
- Recommended Tools: Use hand tools only. If you choose a cordless driver, set the speed to low and the clutch to the bottom 1/3 of the torque settings.
- Forbidden Tools: Do NOT use pneumatic air tools or drill drivers without clutch controls.
- Pro Tip: Always hand-start screws into inserts first to prevent cross-threading. High torque will strip inserts—take your time.
- Bed Liner Check: Spray-on liners are good to go. Drop-in plastic bed liners are not compatible and must be removed before starting.Stripped an insert anyway? Don’t panic—call our support team for a quick repair kit.
INSTALL VIDEO
High tech link to video here or you can visit decked.com/installvideo

HARDWARE BOX
- PREP RANGER
- NUTS AND BOLTS
- XY WHEELS
- MS SCREWS
- MS BOLTS
- D-RINGS
- MS D-RINGS HW
- WHEEL BRACKETS
- DRAWER BIN HW
- WHEEL STOPS
- TORSION BRACE HW
- MS PLUGS
- STUBBIES TURNBUCKLES
TOOLS REQUIRED
- 1/2” and 3/8” socket
- 7/16” socket and/or wrench
- 7/16” open end wrench
- Torx Plus 40 driver (TP40)
- Torque wrench
- 3/16”, and 7/32” hex key
- We included a 3/16” and 7/32” hex key for your tool kit but you may prefer to use your own.
- Trusted friend with a weak mind and a strong back.
ASSEMBLY OVERVIEW

ARE YOU ADDING A CARGOGLIDE TO YOUR DRAWER SYSTEM?
- You will need CargoGlide Mounting Brackets. If you do not have these, they are available on our website.
- The brackets and CargoGlide can be added after installing the Drawer System into your truck bed.
INSTALL: PREP BED
- Remove factory cabside tie downs with a TP40 driver. Save the bolts.
- There are left and right DECKED tie downs.
- Install the DECKED tie downs with the factory bolts as shown.
- Tighten to a torque rating of 20 N-m.
NOTE: If your bolts are old, rusted or corroded, purchase new bolts from a certified OEM supplier.
STEP 1: NUTS AND BOLTS
READ THIS: All fasteners need to be tightened just until snug. Do not overtighten as this can damage the system.
- Assemble the following outside of the truck. Arrange the left and right C-channel assemblies on a flat surface. The feet with the axles installed are the TAILGATE side. NOTE: The wheel bumpers are pre-installed on the cabside of the C-channels. Confirm they are in place.
- On the TAILGATE side only, inside the C-channel, find the single slotted holes. NOTE: The single slotted hole will be on the bottom portion of the C-channel on the left side and on the top portion of the C channel on the right.
- From inside the C-channel, install a 1” bolt from the NUTS AND BOLTS bag through the left and right single slotted holes and through the corner feet. Secure with a flanged nut on the outside of the foot, but LEAVE LOOSE. The tailgate side tie down bracket bolts should also be loose. IMPORTANT: All bolt heads must be on the inside of the C-channels.

STEP 2: COMPLETE THE C
- Locate the two bolts securing the middle tie downs. Confirm the tie down brackets are level (wing panels will not fit properly with unlevel tie down brackets) and tighten the two middle C- channel bolts on both C-channel assemblies. DETAIL A.
- Confirm the CABSIDE tie down brackets are level and tighten the two C-channel bolts on both C-channel assemblies.
- Find the single slotted holes inside the C-channels on the CABSIDE of the assembly.
- On the cabside, from inside the C-channel, install a 1” bolt from the NUTS AND BOLTS bag through the left and right single slotted holes and through the corner feet. Secure with a flanged nut on the outside of the foot. Tighten until snug. IMPORTANT: All bolt heads must be on the inside of the C-channels.
NOTE: Leave the three TAILGATE C-channel bolts on each side loose for panel placement.
STEP 3: CLOSE IT OUT
- On the cabside of the assembly, install the cabside closeout panel with two hex head screws from the MS SCREWS bag.
NOTE: Use the round hole in the foot and the oval hole in the closeout panel.
ANOTHER NOTE: These are being installed directly into the plastic; DO NOT OVER-TIGHTEN. Tighten just until seated. - Place the center deck panel on the assembly. The ruler plate location goes on the tailgate end.
- Start at the cabside. Align the three cabside panel mounting holes over the inserts in the cabside support feet on each side.
- Shift the tailgate feet forward/backward to align the inserts in the feet to the mounting holes in the panel on the tailgate side.
- Stretch your hamstrings.

STEP 4: BIG DECK ENERGY
- Use four dogpoint bolts from the MS BOLTS bag, one in each corner at the triangle marks ONLY, to install the deck panel to the inserts in the corner feet. Refer to diagram for correct placement. Tighten just until snug. DETAIL A.
- Tighten the three tailgate side C-channel nuts and bolts on each side, ensuring the tie down brackets remain level. The wing panels will not fit if the tie down brackets are not level.

STEP 5: WHEEL OF TORSION
- Align the torsion brace over the mounting holes in the tailgate feet.
- Install one hex head screw from the MS SCREWS bag into the through the far left torsion brace hole and into the foot. Repeat with the same fastener on the far right mounting location.
NOTE: These screws are being installed directly into the plastic. Tighten just until seated. Do not over-tighten. - Insert a dogpoint bolt from the TORSION BRACE HW bag through the left interior torsion brace mounting hole and feet.
- Secure with a flanged nut on the inside of the foot. DETAIL A. Tighten until snug. Repeat on the interior hole on the right side.
- Install the SMALL wheels and bolts onto the tailgate feet axles.


STEP 6: STUBBIES
- Grab your trusted friend and carefully carry and place this assembly into your truck bed.
- Install stubbies into each stubby slot. You may need to lift the assembly on each side to install the stubbies.
- Push the stubbies inward and make sure they are fully seated.
NOTE: Short beds will have 6 stubbies total. Long beds will have 8 stubbies total. 
STEP 7: TIE ‘ER DOWN
- Attach the cabside turnbuckles only. Use the longer turnbuckles at the cabside.
- Prep the Turnbuckles: Unscrew the jam nuts all the way out toward the hooks to open them fully.
- Adjust Length: Hold both hooks stationary and rotate the center take-up barrel to extend or retract the turnbuckle. Make sure the hook lengths are equal to each other.
- Find Your Anchor: Pre-adjust the turnbuckle to reach from the truck bed bracket (or DECKED replacement tie down bracket) to a round hole in the DECKED C-channel bracket (DETAIL A). Use whichever upper ROUND HOLE offers the best fitment.
- Attach: Hook one end into your chosen round hole on the DECKED bracket and the other end into the bed bracket or DECKED replacement tie down bracket.
- Hand-Tighten (Do Not Over-Tighten): Verify the system is centered in the truck bed. Hand-tighten the turnbuckle until all slack is gone and it no longer wiggles. Stop once snug. No extra turns are necessary. Over-tightening will pull the system out of alignment.
- Lock in Place: Spin the jam nuts down firmly against the center take-up to secure the setting. Tighten them with a 7/16” wrench.
Note: Leave the tailgate turnbuckles off for now. 
STEP 8: TIME TO WING IT
- Remove the stash bin and access lids from the wingers.
- Place the left and right wingers on the assembly.
- Use the remaining bolts in the MS BOLTS bag to install the wingers to the assembly. NOTE: You’ll have two extra bolts if you have a short (5’) bed.

- D-Rings may be installed in any of the six locations depending on your liking. Most sane people use the four corners. You can purchase additional D-Rings
on our website. - Install D-Ring flat side down on top of silver spacer. Place a small black washer on top of the D-ring and fasten with bolt. Tighten fully with a 3/16” hex wrench (included in your hardware kit). DETAIL A.
- Install the large black washers and bolts in the unused tie down locations. DETAIL B.

STEP 10: BUILD THAT TRAY
NOTE: Perform the following steps on a table or raised, flat surface. You can even use the DECKED carton with the flaps closed.
- Leave the banding on the tray assembly. Set the tray assembly on a table or carton with the track channels facing up and the four mounting holes closest to you. The tray bin is installed on the end with the holes.
- Position the side aluminum pieces so they are even with the side of the tray with no mounting holes. DETAIL A – this page.
- Use a 3/16” hex wrench to loosely install the 3/4” long screws through the inside and tab on the drawer bin and into the weld strip below the bin. Leave loose. DETAIL B.
- While supporting the tray bin, evenly insert and slide the weld strips into the left and right tray channels on the side with the holes. Leave the bin screws loose.
- Insert the tray edge in between the tabs on the tray bin. You’ll know the tray is in place when you can see the bin mounting holes through the slat holes from below. DETAIL C.


STEP 11: BE SQUARE
- Use the hex drive screws from the MS SCREWS bag to install the tray bin. You’ll need to pull the assembly off the table/carton slightly to install from underneath. These are installed directly into the polymer – tighten just until seated. Do not overtighten.
- Push the aluminum side channels all the way against the tray bin wall.
- Tighten the bin/weld strip screws, two on each side. IMPORTANT: Check that both the left and right side channels are flush against the bin walls (DETAIL B). If this isn’t correct, the tray won’t be square, the other tray parts will not align correctly, and the tray may not function or latch properly.
- You can remove the tray strap at this point.
- Flex for the neighbors.

STEP 12: WALL BUILDING
- Insert five 1/2” hex head bolts into each channel.
- Lay the left and right wheel brackets next to the tray at the cabside end. The flanges should face up.
- Lay the left and right high sides ON TOP of the wheel brackets and next to the tray so that the mounting holes align to each other. The flanges should face up.
- Slide the hex bolts in the channels to align to the mounting locations in the wheel brackets and high sides.

STEP 13: SECURE THE PERIMETER
- Lift the high side and wheel bracket slightly to install the 7/16” long hex drive bolts and nuts. Leave loose.
- Place the high side/wheel bracket flanges over the channel bolts.
- Use the 1/2” nuts to secure the high side/wheel bracket assembly to the channel bolts. Leave all fasteners loose.

STEP 14: ONE BIG ASS DRAWER
- Insert the bottom tab on the back plate into the groove in the bottom of the tray and rotate up into position. The back plate should rest against the wheel brackets and side frame.
- Install the 7/16” long hex drive bolts and nuts to secure the back plate to the cabside flange of the wheel bracket. Tighten until snug.
- Confirm alignment of the highsides, wheel brackets and cabside back plate. Tighten all loose fasteners.
- Install both BIG wheels into the wheel brackets.
- Clip the wheel stops around the side rails. The wheel stop marked with the R is installed on the right/passenger side.
- Install the other wheel stop, marked with an L, on the left/driver side (not shown).

STEP 15: THE HOME STRETCH
- Carefully lift the tray assembly and slide the wheels into the C-Channels.
- Holding the tailgate side higher, slide the tray in until the wheel stops clear the tailgate wheels.
- Level out the tray and slide all the way in.
- Install stash bins where you want them. Additional stash bins can be ordered from our website.
- Install the two stash bin lids and two access lids.
- Install the ruler using four 3/16” hex drive screws. Do not over torque, torque boy. Just get ‘em snug.
- Install stash bin plugs. Make sure they are fully seated.
- Install tray bin plug or lock (if purchased).
- The weatherstrip will be installed on the tray bin. Confirm the wiper blade is pointing towards the inside of the tray as shown.

NOTE: Facing the weatherstrip the wrong way will funnel water into the drawer: BAD! 

STEP 16: THAT’S A WRAP
- Roll the tray in and out a couple of times to ensure proper function.
- Confirm the system is centered in the bed.
- Install and tighten the tailgate turnbuckles, using one of the round holes in the tie down bracket. DETAIL A. IMPORTANT: The tailgate turnbuckles must be installed as the last step. Tighten turnbuckles just until they stop wiggling. Do not add any extra turns. Tighten the jam nuts against the takeup with a 7/16” wrench.
Check the turnbuckles periodically, at least once every three months, to confirm they are tight.
CONGRATS, GAME CHANGER! YOU DID IT.
Crack open a cold one of your liking, sit back and admire your work. Now get busy organizin’!
DECKED PRODUCTS LIMITED LIFETIME WARRANTY
(Valid on DECKED Products purchased on or after 8/1/2021) DECKED LLC, (the “Manufacturer”) warrants the original purchaser only that DECKED Truck and Van Products (The “DECKED” Product) will be free from defects in material and workmanship from the date of purchase and continuing for the expected lifetime of the DECKED Product. The DECKED Product must be registered by the original purchaser with DECKED, LLC via its website at, decked.com/register, and a copy of the original sales receipt must be supplied to the Manufacturer at the time a warranty claim is made. This warranty terminates if the original purchaser transfers the DECKED Product to any other person or vehicle.
WHAT IS COVERED
All DECKED Products identified above on or after August 1, 2021. DECKED’s Limited Lifetime Warranty applies to US and Canadian customers only. International shipments are covered by DECKED’s 3 Year Limited Warranty.
WHAT WE WILL DO TO CORRECT PROBLEMS
Subject to the limitations and exclusions described in this limited warranty, the Manufacturer will remedy defects in workmanship or materials by providing one of the following remedies at its option and without charge to the original purchaser for parts: (a) repairing the defective portion of the DECKED Product or (b) replacing the entire DECKED Product. In addition, the Manufacturer may elect at its option not to repair or replace the DECKED Product, but rather issue to the original purchaser a refund equal to the purchase price paid for the DECKED Product or a credit to be used towards the purchase of a new DECKED Product.
WHAT IS NOT COVERED
This limited warranty expressly excludes:
- Damage or defects caused by normal wear and tear, cosmetic rust, scratches, accidents, unlawful vehicle operation, installation in a non-supported vehicle or installed in a vehicle which does not match the DECKED Product’s SKU-intended fitment or use, or modification
of the product, or any types of repair of a DECKED Product other than those authorized or provided by the Manufacturer. - Damage or defects resulting from conditions beyond
the Manufacturer’s control and specifications including, but not limited to modification, misuse, overloading, or failure to assemble, install or use the DECKED Product in accordance with the Manufacturer’s written instructions or guidelines included with the DECKED Product or separately made available to the original purchaser. - Damage to the contents of the DECKED Product or vehicle.
- TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE, OR INABILITY TO USE THE DECKED PRODUCT OR THE MANUFACTURER’S NEGLIGENCE.
NO OTHER EXPRESS WARRANTY APPLIES
This Limited Lifetime Warranty is the sole and exclusive warranty for DECKED Products. No employee, agent, dealer, or other person is authorized to alter this warranty or make any other warranty on behalf of DECKED LLC.
NOTIFICATION PROCEDURES
If the DECKED Product does not conform with the terms of this limited warranty, the original purchaser must promptly notify the Manufacturer in writing upon discovery of the nonconformity. In order to receive remedies under this limited warranty, a warranty claim must have been registered with DECKED LLC by the original purchaser, must describe the nature of the products nonconformity, include a copy of the original sales receipt, invoice, or other proof of purchase and be accompanied with photos or video. Repairs or modifications made to the DECKED Product by other than the Manufacturer or its authorized agent will nullify this limited warranty. Coverage under this limited warranty is conditioned at all times upon the owner’s compliance with these required registration, notification, and repair procedures.
Product registration may be performed at: decked.com/register Warranty claims must include reciprocal contact information and may be made via certified mail or email to: DECKED Warranty and Claims PO Box 885 Ketchum, ID 83340 warranty@decked.com 208-806-0251
Register your system at decked.com/warranty
PATENTS
Covered by one or more patents: www.decked.com/pages/patents
Documents / Resources
![]() | YF3 DECKED Drawer System |
References
- User Manualmanual.tools

