TP-Link Omada Quick Installation Guide

1 Overview

Package Contents

• EAP
• Screw (For Securing the Grounding Wire)
• Installation Guide
• Passive PoE Adapter (Mounting Bracket Included)
• Power Cord*
• Waterproof Kit (Spiral Cover, Seal, Bracket, O-Ring)
• Mounting Kit (Mounting Bracket for EAP, Plastic Wall Anchors, Self-tapping Screws, Pole Mounting Strap)

* PoE Adapter and Power Cord are not included in the package contents of certain models. Refer to product specifications or datasheet.

Panel Layout

RESET Button: Resets the device to factory default settings.

SYS LED: Indicates system status.

• Flashes green twice: Initialization completed.
• Solid green: Device initializing or working properly.
• Flashing yellow: System errors (RAM, Flash, Ethernet, WLAN, or firmware malfunctioning).
• Slowly Flashing yellow, green: Firmware update in progress.
• Quickly flashing green: Locate the device.
• Quickly flashing yellow, green: Device being reset to factory default settings.
• Slowly flashing green: Device in an isolated state.

Ethernet Port: Connects to the network.

Grounding Terminal: Connects to grounding facilities.

Power LED: Indicates power status.

PoE Port: Connects to the PoE adapter or PoE switch.

Passive PoE Adapter

POE Port: Connects to the EAP.

LAN Port: Connects to a router or switch.

RESET Button: Resets the adapter.

Notes:

• PoE Adapter may not be included in certain models.
• PoE Adapter may vary by model.

2 Lightning and ESD Protection

Proper grounding is crucial for outdoor devices. Connect the grounding terminal to grounding facilities using a proper grounding wire that meets local installation requirements. Secure the grounding wire to the grounding terminal with the provided screw.

Diagram Description: An illustration shows the EAP mounted outdoors, with an Ethernet cable running from the EAP to a grounded PoE adapter, which is then connected to a grounded 3-wire power outlet.

3 Hardware Installation

The EAP can be pole-mounted or wall-mounted.

Option 1: Pole Mounting

1. Lead the end of the pole mounting strap through the back of the EAP.
2. Position the EAP and wrap the pole mounting strap around the pole. Feed the end through the screw-block and tighten the strap until the EAP is secure.

Option 2: Wall Mounting

1. Place the mounting bracket for the EAP in the correct position. Mark positions for the screw holes. Drill holes for the screws at the marked positions.
2. Insert the plastic wall anchors into the holes. Align the mounting bracket to the plastic wall anchors and drive the self-tapping screws into the anchors through the mounting bracket.
3. Align the mounting tabs on the back of the EAP with the slot of the mounting bracket. Push and slide the EAP downward until it locks into place.

Connect the Cable

1. Fit an Ethernet cable through the Spiral Cover, Bracket, and O-Ring, and connect the cable to the port.
2. Fit the O-Ring to the head of the Bracket and screw the Bracket to the body of the device. Ensure the O-Ring is not warped.
3. Fit the Ethernet cable through the Seal's slit (thicker side towards the Bracket) and plug the seal into the Bracket. Choose the appropriate Seal based on the Ethernet cable type and diameter.
4. Screw the Spiral Cover to the Bracket.

4 Software Configuration

Choose from the following methods to set up your EAPs:

• Method 1: Standalone Mode: Configure and manage EAPs individually. Suitable for small networks.
• Method 2: Controller Mode: Configure and manage EAPs in batches using the Omada Controller.

Method 1: Standalone Mode

Via Omada App

1. Download and install the TP-Link Omada App from the App Store or Google Play.
2. Connect your mobile device to the EAP using the default SSID printed on the back of the product.
3. Open the Omada App, navigate to Standalone Devices > APs, and wait for the EAP to appear. Tap the EAP to configure it.

The Omada App is for quick configuration of common settings. For advanced settings, use the EAP's web page or Controller Mode.

Via Web Browser

1. Connect your device to the EAP using the default SSID printed on the back of the product.
2. Launch a web browser and enter http://tplinkeap.net in the address bar. Log in using 'admin' for both Username and Password.
3. Set up a new Username and Password for secure management.

To configure other EAPs, connect your device to each EAP using its default SSID and repeat the steps. Basic functions can be configured in Standalone Mode; use Controller Mode for advanced functions.

Method 2: Controller Mode

Choose from two types of Omada Controller:

• Type 1: Omada Software Controller: Download and install from https://www.tp-link.com/support/download/omada-software-controller/. Requires a PC running Windows or Linux. The controller must remain running on the computer.
• Type 2: Omada Hardware Controller: A separate hardware device, purchased additionally. Refer to its Installation Guide for details.

Via Omada App

1. Download and install the TP-Link Omada App.
2. Launch the Omada App and configure the controller for local or remote management.

Local Management: Connect to the EAP's default SSID, launch the Omada App, go to Local Access, tap '+' to add the controller, then launch it to manage devices.

Remote Management: Ensure controller and mobile device have internet access. For Software Controller, enable Cloud Access and bind your TP-Link ID. For Hardware Controller, ensure Cloud LED is flashing slowly. Log in to the Omada App with your TP-Link ID and go to Cloud Access.

Via Web Browser

1. Open the Omada Controller's web page.
• Software Controller: Launch from your PC or click 'Launch a Browser to Manage the Network'.
• Hardware Controller: Find its IP address on your router's DHCP client list, then enter it in the browser.
2. Follow the wizard to complete the quick setup.
3. Log in with your created username and password.
4. Remote Management: Access via https://omada.tplinkcloud.com using your TP-Link ID.

Additional Information

For detailed configurations, download the EAP User Guide from https://www.tp-link.com/support.

Join the TP-Link Community at https://community.tp-link.com for questions and support.

For technical support, user guides, and more information, visit https://www.tp-link.com/support or scan the QR code.

Safety Information

• Keep the device away from fire or hot environments. Do not immerse in water or any other liquid.
• Do not attempt to disassemble, repair, or modify the device. Contact TP-Link for service.
• Do not use the device where wireless devices are not allowed.
• Use only recommended chargers.
• Do not use damaged chargers or USB cables.
• The adapter should be installed near the equipment and be easily accessible.
• The adapter should be used indoors where the ambient temperature is 40 °C or lower.
• Plug the adapter into wall outlets with an earthing connection through the power supply cord.

Regulatory Information

Attention: In EU member states, EFTA countries, and Northern Ireland, operation in the 5150MHz-5350MHz frequency range is permitted indoors only.

Attention: In Great Britain, operation in the 5150MHz-5350MHz frequency range is permitted indoors only.

For EAP Controller, go to Access Point page and select the desired EAP to specify the channel. For web browser, go to Wireless > Wireless Settings to specify the channel.

EAC Compliance: AT BE BG CH CY CZ DE DK EE EL ES FI FR HR HU IE IS IT LI LT LU LV MT NL NO PL PT RO SE SI SK UK(NI)