Manuals+

Sunrise Alarm Clock with Himalayan Salt Lamp & Wireless Charger

Instruction Manual

Model: XO-9917

Introduction

READ ALL INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THIS MANUAL.

In the Box

  • XO-9917 Sunrise Alarm Clock with Wireless Charger (x1)
  • Power Cable (x1)
  • User Manual (x1)

Safety Precautions

  • This product is NOT a toy; keep away from children and pets.
  • Only use the device according to the instructions in this manual. Never use the device for anything other than its intended purpose.
  • This device is NOT a substitute for proper medical equipment or attention.
  • ONLY use the supplied power cable.
  • Do not open this product or attempt to repair the unit yourself if it is not working properly. Doing so risks fire, shock, or injury.
  • When not in use, the device should be stored in a dry, cool location, away from sources of water or heat.
  • Do not expose the device or power cable to extreme temperatures (heat or cold), open flames, humid or wet conditions.
  • Do not submerge in water. Do not use in a location where the device or power cable could fall into liquid.
  • Unplug the charging cable when not in use. Do not pull the charging cable to disconnect, or use the cable as a handle.
  • Do not use if the device or power cable is damaged. If the device or power cable is damaged, it MUST be serviced or replaced by the manufacturer or its service agent before using again.
  • Attachments on the back of your device can impede the effectiveness of the wireless charger and lead to overheating. Remove attachments from your device before charging on this wireless charger.

Product Overview & Connectivity

The device features a [Snooze/Light] button on top for controlling the bedside light. The back of the clock has buttons labeled [Set], [Up], and [Down], along with ports for USB power input (INPUT 5V/1A) and USB power output (OUTPUT 5V/2A).

Diagram shows the front of the clock with a "Wireless Charging Surface" and a "Clock Display" showing "88:88".

Diagram shows the back of the clock with control buttons and ports.

Connecting to Power

  • Plug the small connector of the included charging cable into the USB-C charging port on the clock.
  • Plug the large connector into a USB power source, such as a compatible 5V/2A USB power adapter (not included), and plug into a wall outlet.

The clock display will turn on when connected to power. If disconnected, it saves time and settings for 60 seconds.

Display Modes

  • Press the [Up] button to switch between clock display modes.
  • Press the [Set] button to save the current mode as the default.
  • Mode 1: Shows time for 10 seconds, then date and temperature for 2 seconds.
  • Mode 2: Shows time, alarm, date, and temperature at all times.

Setting the Time

  1. Press the [Set] button until the time is displayed.
  2. Press and hold the [Set] button to set the time. The hour digits will flash.
  3. Press the [Up] and [Down] buttons to adjust the hour. A dot in the upper left corner indicates PM.
  4. Press the [Set] button to save the hour.
  5. The minute digits will flash. Press the [Up] and [Down] buttons to adjust the minutes.
  6. Press the [Set] button to save the minutes. The clock returns to the default display mode.

Display example shows "AM 00:00" and "PM 00:00".

Setting the Alarm

  • Press the [Set] button until the alarm time is displayed.
  • Press the [Down] button to turn the alarm ON or OFF. A dot in the lower left corner of the display lights up when the alarm is ON.

When the alarm is ON:

  1. Press and hold the [Set] button to set the alarm time. The alarm hours will flash.
  2. Press the [Up] and [Down] buttons to adjust the alarm hours.
  3. Press the [Set] button to save the alarm hour.
  4. The alarm minute digits will flash. Press the [Up] and [Down] buttons to adjust the alarm minutes.
  5. Press the [Set] button to save the alarm minutes. The clock returns to the default display mode.

Display example shows "Alarm OFF 00:00" and "Alarm ON 00:00".

Setting the Date

  1. Press the [Set] button until the date is displayed.
  2. Press and hold the [Set] button to set the date. The year digits will flash.
  3. Press the [Up] and [Down] buttons to adjust the year.
  4. Press the [Set] button to save the year.
  5. The month digits will flash. Press the [Up] and [Down] buttons to adjust the month.
  6. Press the [Set] button to save the month.
  7. The day digits will flash. Press the [Up] and [Down] buttons to adjust the day.
  8. Press the [Set] button to save the day. The clock returns to the default display mode.

Changing Temperature Units

  1. Press the [Set] button until the temperature is displayed.
  2. Press the [Down] button to switch between degrees Fahrenheit (°F) and Celsius (°C).
  3. Press the [Set] button to save the unit. The clock returns to the default display mode.

Using the Bedside Light

  • Press the [Snooze/Light] button on the top of the clock to turn the bedside light ON in white light mode.
  • Press the [Snooze/Light] button to adjust the light brightness (low, medium, high).
  • Press and hold the [Snooze/Light] button to switch to color-changing light mode.
  • In color-changing mode, press the [Snooze/Light] button to choose a light color.
  • Press and hold the [Snooze/Light] button again to switch back to white light mode.

Note: The bedside light can only be turned OFF from white light mode. It cannot be used during sunrise or snooze modes.

Using the Sunrise Light

The sunrise light function activates 20 minutes before your alarm time, gradually increasing brightness until the alarm sounds.

To use this feature, set the alarm before going to sleep.

Snooze Function

  • When the alarm sounds, press the [Snooze/Light] button to activate the snooze function. The alarm will ring again in 5 minutes. The sunrise light remains at full brightness during snooze.
  • To turn off the alarm and sunrise light completely for the day, press and hold the [Snooze/Light] button when the alarm is sounding. They will activate normally the next day.

Wireless Charging & USB Output

  • When connected to power, the LED indicator flashes RED and BLUE alternately, then turns RED, indicating standby mode.
  • Place a wireless charging-enabled device on the charging pad to begin charging automatically. The LED indicator glows BLUE when charging properly.
  • If charging does not start, reposition the device or remove its case.
  • When fully charged, the LED indicator turns RED. Remove the device from the pad.
  • Note: Flashing RED and BLUE indicates the device is not wireless charging enabled or an object is interfering with charging.
  • To charge a USB device using the USB power output port, plug your device's USB connector into the port on the back of the clock.

Tech Specifications

  • USB-C Input: DC 5V/2A
  • Wireless Charging Output: 5W (Max)
  • USB-A Output: DC 5V/1A

FCC Information

This device complies with Part 15 of the FCC rules. Operation is subject to two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Radiation Exposure Statement

This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. During the operation of the device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

FCC logo and "Made in China" text are present.

Models: XO-9917, XO9917, 2ALCFXO-9917, 2ALCFXO9917, Sunrise Alarm Clock with Himalayan Salt Lamp and Wireless Charger, XO-9917 Sunrise Alarm Clock with Himalayan Salt Lamp and Wireless Charger

PDF preview unavailable. Download the PDF instead.

GetApplicationAttachment.html?id=5361832 Microsoft PowerPoint 2019

Related Documents

Preview Sunrise Alarm Clock with Himalayan Salt Lamp & Wireless Charger - EAC-SU21 Instruction Manual
Comprehensive instruction manual for the EAC-SU21 Sunrise Alarm Clock, featuring a Himalayan Salt Lamp and Wireless Charger. Learn how to set time, alarms, use the light functions, and wireless charging.