LTECH C3 Remote Control Instruction Manual

LTECH C3 Remote Control

LED Color Controller Kit

• The controller housing is made from Covestro/Samsung V0-rated flame-retardant PC material;
• Features a soft-start gradual dimming function for greater visual comfort;
• Featuring a streamlined design and magnetic attachment, it is powered by two AAA batteries ;
• Utilizes 2.4 GHz RF wireless transmission for stable signals and strong interference resistance;
• Equipped with a dedicated on/off button for one-touch lighting control;
• Quickly adjust color using the color temperature and color touch sliders;
• Press the brightness button briefly to adjust the brightness across 11 levels; press and hold for continuous dimming;
• Pre-programmed with 2 scene modes for quick access, and custom scenes can be saved by holding down the button;
• A single controller can be paired with up to 10 remotes, and a single remote control can be used with multiple controllers;
• Supports synchronized dimming for controller groups

Technische Spezifikationen

C3 Fernbedienung

P3 Controller

Maße

Produktinstallation

1. Open the battery compartment on the remote control and insert two AAA batteries, making sure to insert them with the correct polarity.
2. Peel off the protective film from the included double-sided tape, attach the magnetic mount to the wall, and press firmly to secure it (let it sit for 24 hours to ensure a secure bond before placing the remote control on it to prevent it from falling off).
3. Attach the remote control to the magnetic mount to complete the installation.

Funktionsbeschreibung

• ON Button: Press briefly to turn on; press and hold for 2 seconds to pair.
• OFF Button: Press briefly to turn off.
• Color Touch Slider: Touch to change the RGB color of the lights.
• Brightness button: Press briefly to increase or decrease brightness; press and hold for continuous dimming. A brief press cycles through 11 brightness levels, while a press and hold allows for continuous dimming.
• Scene Button: Press briefly to recall a scene; press and hold for 2 seconds to save the current lighting state to a scene, and the indicator light will flash red twice.
• Indicator Light: The indicator light changes in sync with adjustments to color and brightness.

Notiz:

1. If the indicator light on the remote control does not light up when a button is pressed, the batteries may be dead. Please replace the batteries promptly.
2. If no buttons are pressed for 6 seconds, the remote control will enter sleep mode. Press any button to wake it up.

Schaltplan

Vorsichtsmaßnahmen bei der Installation

For use with P-series controllers

Key pairing code

1. Short press the ID learning button on the controller. The load indicator will flash.
   Please complete the following steps within 10 seconds.
2. Koppeln der Fernbedienung:
   Halten Sie die EIN-Taste auf der Fernbedienung 2 Sekunden lang gedrückt.
   The remote control indicator light will flash rapidly three times and then turn off.
   If the color temperature slider or color slider changes when touched, the learning process was successful.

Power-on code pairing

1. After the controller has been powered off and then powered back on, please complete the following steps within 10 seconds.
2. Koppeln der Fernbedienung:
   Press and hold the ON button on the remote control for 2 seconds. The remote control’s indicator light will flash rapidly three times and then turn off, and you will feel a change when touching the slider, indicating that the programming was successful.

Notiz: A single controller can pair with up to 10pcs remote controls. If more than 10pcs remote controls are paired, the ID code of the first remote control will be automatically deleted.

Code löschen

To delete all remote controls:
Press and hold the controller ID learning button for 6 seconds. The controller load light will flash 4 times quickly and then stay on, indicating successful code clearing.

Use the Remote Controls Together

Code Pairing (assuming B learns from A)

1. Press and hold the ON and OFF buttons on the remote control simultaneously until the indicator light stays on, then release them.
2. Within 5 seconds, press any button on Remote A. The indicator light on Remote B will flash twice rapidly and then turn off, indicating that the pairing was successful.

*Assuming Remote Control A has already been paired with the controller, if you program Remote Control B to mimic Remote Control A, Remote Control B can be used to control the system directly without needing to be paired with the controller; *Only remotes of the same model can be programmed to mimic each other

Code löschen

Press and hold the S1 and S2 buttons on the B remote control simultaneously for about 10 seconds; when the indicator light flashes three times, the programmed remote control code will be cleared.

Transport und Lagerung

Transport

Der Versand der Produkte kann per Fahrzeug, Boot und Flugzeug erfolgen.
During transportation, products should be protected from rain and sun. Please avoid severe shock and vibration during the loading
and unloading process.

Lagerung
Die Lagerbedingungen sollten den Umweltstandards der Klasse I entsprechen. Bei Produkten, die länger als sechs Monate gelagert wurden, wird eine erneute Prüfung empfohlen und eine Verwendung erst nach erfolgter Qualifizierung möglich.

Aufmerksamkeiten

• Bitte in trockenen Innenräumen verwenden;
• When installing the battery, please connect the positive and negative terminals correctly. If the remote will not be used for a long period, take the battery out;
• When the remote distance is shortened and/or the remote doesn’t work frequently, please change the battery in time;
• Bitte nehmen Sie es vorsichtig und legen Sie es ab, um Stürze zu vermeiden, die Schäden verursachen könnten.
• Versuchen Sie im Falle eines Defekts bitte nicht, die Produkte selbst zu reparieren. Bei Fragen wenden Sie sich bitte an Ihren Lieferanten.

Dieses Handbuch kann ohne vorherige Ankündigung geändert werden. Produktfunktionen sind von der Ware abhängig. Bei Fragen wenden Sie sich bitte an unsere offiziellen Vertriebspartner.

Gewährleistungsvereinbarung

• Gewährleistungsfristen ab Lieferdatum: 5 Jahre.
• Innerhalb der Gewährleistungsfristen werden kostenlose Reparatur- oder Ersatzleistungen bei Qualitätsproblemen erbracht.

Garantieausschlüsse unten:

The following conditions are not within the guarantee range of free repair or replacement services:

• Außerhalb der Gewährleistungsfristen;
• Jeder künstliche Schaden, der durch hohe Vol. verursacht wirdtage, Überlastung oder unsachgemäße Bedienung;
• Produkte mit schweren physischen Schäden;
• Schäden durch Naturkatastrophen und höhere Gewalt;
• Garantieetiketten und Barcodes wurden beschädigt.
• Es wurde kein Vertrag von unserem Unternehmen unterzeichnet.

1. The repair or replacement provided is the only remedy for customers. Our company is not liable for any incidental or consequential damage unless it is within the law.
2. Unser Unternehmen behält sich das Recht vor, die Bedingungen dieser Garantie zu ändern oder anzupassen; eine schriftliche Freigabeerklärung ist jedoch maßgebend.