Singer Model 1116 Sewing Machine Instruction Manual

Einführung

Congratulations on your new Singer sewing machine. You are about to begin an exciting adventure in creativity. From the moment you first use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made.

We recommend that, before you start to use your sewing machine, you discover the many advantages and the ease of operation by going through this instruction book, step by step, detailed for your machine.

Um sicherzustellen, dass Sie stets über die modernsten Nähmöglichkeiten verfügen, behält sich der Hersteller das Recht vor, das Aussehen, das Design oder das Zubehör dieser Nähmaschine nach Bedarf zu ändern.

SINGER® is a registered trademark of The Singer Company Limited. Copyright © 2000. All rights reserved throughout the world.

Image: Page from the Singer Model 1116 Instruction Manual displaying the 'Congratulations' message and copyright details.

Wichtige Sicherheitshinweise

Beim Gebrauch eines Elektrogeräts sollten immer grundlegende Sicherheitsvorkehrungen getroffen werden, darunter die folgenden:

1. Lesen Sie alle Anweisungen, bevor Sie diese Nähmaschine verwenden.
2. GEFAHR – So verringern Sie das Risiko eines Stromschlags:
   • Always unplug sewing machine from the electric outlet immediately after using and before cleaning.
   • Always unplug before changing the light bulb. (Replace bulb with same type rated 15 watts).
3. WARNUNG – Um das Risiko von Verbrennungen, Feuer, Stromschlag oder Verletzungen zu verringern:
   • Darf nicht als Spielzeug verwendet werden. Wenn diese Nähmaschine von oder in der Nähe von Kindern benutzt wird, ist besondere Aufmerksamkeit erforderlich.
   • Verwenden Sie diese Nähmaschine nur für den in diesem Handbuch beschriebenen Verwendungszweck. Verwenden Sie nur vom Hersteller empfohlene Zubehörteile, die in diesem Handbuch enthalten sind.
   • Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to the nearest authorized service center for examination, repair, electrical or mechanical adjustment.
   • Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot controller free from accumulation of lint, dust, and loose cloth.
   • Halten Sie die Finger von allen beweglichen Teilen fern. Besondere Sorgfalt ist um die Nähmaschinennadel erforderlich.
   • Verwenden Sie immer die richtige Stichplatte. Bei Verwendung einer falschen Platte kann die Nadel abbrechen.
   • Verwenden Sie keine gebogenen Nadeln.
   • Ziehen oder drücken Sie den Stoff beim Nähen nicht. Dadurch kann die Nadel abgelenkt werden und brechen.
   • Switch the sewing machine off ("0") when making any adjustments in the needle area such as threading the needle, changing the needle, threading the bobbin, or changing the presser foot.
   • Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or making any other user servicing adjustments mentioned in the instruction manual.
   • Lassen Sie niemals Gegenstände in Öffnungen fallen oder stecken Sie sie hinein.
   • Nicht im Freien verwenden.
   • Nicht in Bereichen betreiben, in denen Aerosolprodukte (Sprays) verwendet werden oder Sauerstoff verabreicht wird.
   • To disconnect, turn all controls to the off ("0") position, then remove plug from outlet.
   • Ziehen Sie den Stecker nicht am Kabel, sondern fassen Sie ihn am Stecker und nicht am Kabel an.

BEWAHREN SIE DIESE ANWEISUNGEN AUF

Diese Nähmaschine ist nur für den Hausgebrauch bestimmt.

Image: Page from the Singer Model 1116 Instruction Manual detailing important safety guidelines.

Understanding Your Sewing Machine: Principal Parts

Familiarize yourself with the main components of your Singer Model 1116 sewing machine. Refer to the diagrams below for identification.

Image: Diagrams illustrating the principal parts of the Singer Model 1116 sewing machine, with corresponding numbers for identification.

Setup: Threading and Tension

Oberfaden einfädeln

This is a simple operation but it is important to carry out correctly to avoid needle problems. If you have difficulty, start by raising the needle to its highest point (1), and also the take-up lever (2) to release the tension discs. To hold the safety, it is strongly suggested you turn off the main project to confirm machine setting.

1. Lift up spool pin. Place the spool of thread on the holder and push the spool pin off the spool as shown. (3)
2. Lead thread spool, place the thread under the thread guide to the left of the upper spool holder.
3. Guide thread through the upper thread guide. (4)
4. Guide thread around thread guide (5) pulling thread through pre-tension spring (6) as shown.
5. Guide thread through the thread guide down, right, thread and up left channel (8). Bring the thread into the hook of the thread take-up lever (9) down and thread through (10) and gently pull up on the thread.
6. At the top of the needle, guide the thread from right to left into the eye of the take-up lever and then downwards again. (7)
7. Guide thread behind the thin wire needle clamp guide (11) and then down to the needle which should be threaded from front to back. Pull about 6-8 inches of thread to the back of the needle eye. Trim thread to length with built-in thread cutter.

Gewindespannung

Proper thread tension is crucial for balanced stitches.

Oberfadenspannung

Basic thread tension setting: 4.

• Um die Spannung zu erhöhen, drehen Sie den Drehknopf auf die nächsthöhere Zahl.
• Um die Spannung zu verringern, drehen Sie den Drehschalter auf die nächstniedrigere Zahl.
• Correct thread tension for straight stitching (A): Thread tension too loose for straight stitch sewing. Turn dial to a higher number (B).
• Correct thread tension for straight stitch sewing: Turn dial to lower number (C).
• Correct thread tension for zig zag and decorative sewing (D): Correct thread tension is where a small amount of the upper thread appears in the bottom side of fabric.

Lower Thread Tension

To test bobbin thread tension, remove the bobbin case and hold it by suspending it by the thread. Jerk it once or twice. If the tension is correct, the thread will unwind by about an inch or two. If the tension is too tight, it will not unwind at all. If the tension is too loose, it will drop too much. To adjust, gently turn the small screw on the side of the bobbin case. This should only be needed for specialty threads.

Image: Diagrams illustrating the step-by-step process for threading the upper thread and guidelines for adjusting both upper and lower thread tension on the Singer Model 1116.

Bedienungsanleitung

Function of Stitch Length Dial: Straight, Fine, Triple Straight Stitch

The stitch length dial selects the length of your stitches. For most stitches, this dial will be set between 1 and 4. The settings in this manual are suggestions. It is best for you to practice on a scrap piece of fabric and thread you intend to use for your project to confirm machine settings.

• Allzweckfuß
• Geradstich: General construction, topstitching
  • Stitch length: 2 - 4, dependent on thickness of fabric and thread
  • Select stitch: A
• Dreifacher Geradstich: Quilting, topstitching
  • Stitch length: 2 - 4, dependent on thickness of fabric and thread
  • Select stitch: A
• Fine Stitch: High stress angles and curves, reinforcement
  • Stichlänge: 1
  • Select stitch: A
• Triple Straight (stretch) Stitch: Reinforcement of high stress
  • Stichlänge: 1
  • Select stitch: A

Note: Only change the stitch selection or needle position when the needle is in the highest position.

Zig Zag and the Function of the Stitch Length Dial

The density of zig zag stitches increases as the setting of the stitch length dial approaches "0". Next zig zag stitches are usually achieved at "2.5" or below. Different widths can be set up in the stitch window. Each dial is a different width of zig zag within the C stitch.

• Allzweckfuß
• Zig Zag: General construction, overedge and reinforcement, insertion of elastic or ribbon
  • Select stitch: C
  • Stitch length: 1 - 4
• Rib Rac: General construction on knit fabric, decorative, high stress area, heavy fabric
  • Select stitch: C
  • Stitch length: 1 - 3

Image: Pages from the Singer Model 1116 Instruction Manual detailing the function of the stitch length dial for various straight and zig-zag stitches, with illustrative diagrams.

Overedge, Slant Overedge Stitches

• Allzweckfuß
• Overedge stitch: For finished seams on woven or knit fabric
  • Select stitch: F
  • Stitch length: 1 - 4
• Slant overedge stitch (same as above)
  • Select stitch: G
  • Stitch length: 1 - 4
• Slant stretch overedge stitch (same as above)
  • Select stitch: H
  • Stitch length: 1 - 4

Note: An overcasting foot is an optional accessory not supplied with this machine.

Knöpfe annähen

To sew on buttons, follow these steps:

1. Install the darning plate (1). Place the button on the fabric under the presser foot. Turn the handwheel to check that the needle goes cleanly into the left and right holes of the button (adjust the needle position according to the button by turning the stitch selector dial to the appropriate stitch width), and slowly sew on the button with about 6-8 stitches (2).
2. It is recommended to take a few locking stitches at the beginning and end of sewing. To do this – set the select needle position to a few stationary stitches on one side of the button. Sew on the button as described and repeat the locking stitch on the other side of the button.
3. If a shank is required, place a darning needle on top of the button and sew. For buttons with 4 holes, sew through the front two holes first (2), push work forward and then sew through the back two holes as described (3).

Image: Pages from the Singer Model 1116 Instruction Manual detailing how to perform overedge stitches and the procedure for sewing buttons, with accompanying diagrams.

Wartung

Regular maintenance ensures the longevity and optimal performance of your Singer Model 1116 sewing machine. Always unplug the machine before performing any maintenance.

• Reinigung: Regularly clean lint and dust from the bobbin area, feed dogs, and tension discs using a small brush or lint remover.
• Ölen: Refer to your original machine's service manual for specific oiling points and frequency. Use only high-quality sewing machine oil.
• Nadelwechsel: Change needles frequently, especially when starting a new project or if the needle shows signs of dullness or bending. Use the correct needle type and size for your fabric and thread.
• Lagerung: When not in use, cover your sewing machine to protect it from dust and store it in a dry, stable environment.

Fehlerbehebung bei allgemeinen Problemen

This section addresses common problems you might encounter during operation. For more detailed troubleshooting, consult a qualified service technician.

Manual Specifications (Reproduction)

This section details the physical specifications of this reproduction instruction manual for the Singer Model 1116 sewing machine.

• Produktabmessungen: 8.5 x 5.5 x 0.1 Zoll
• Artikelgewicht: 3 Unzen
• Seiten: 40 Seiten
• Sprache: Englisch
• Reproduction Manufacturer: TabSynth Design
• Date First Available (Reproduction): 1. November 2025

Garantie- und Supportinformationen

This document is a reproduction of the original Singer Model 1116 sewing machine instruction manual. As such, it does not include any warranty information for the sewing machine itself. Any warranty or support for the sewing machine would have been provided with the original purchase of the machine.

For support regarding the operation of your Singer Model 1116, please refer to the instructions provided within this manual. For service or parts related to the sewing machine, please contact a certified Singer service center or a reputable sewing machine repair specialist.

For inquiries regarding this specific manual reproduction, please contact TabSynth Design Works LLC.