Jonard Tools CM-RJ45/8 RJ45-Kabelkennzeichnungen für CM-100

Einführung

This manual provides essential information for the proper use and maintenance of the Jonard Tools CM-RJ45/8 RJ45 Cable Identifiers. These identifiers are designed to work exclusively with the Jonard Tools CM-100 Cable Mapper Pro, facilitating efficient identification and mapping of RJ45 network cables.

Produkt überview

The CM-RJ45/8 kit includes eight (8) numbered RJ45 network cable identifiers. These identifiers are passive devices that, when connected to network cables, allow the CM-100 Cable Mapper Pro to distinguish between multiple cables connected to a patch panel or wall plate.

Hauptmerkmale:

Numbered Identification: Each identifier is clearly numbered from 1 to 8 for easy port mapping.
CM-100 Compatibility: Specifically designed to integrate with the Jonard Tools CM-100 Cable Mapper Pro.
Simultaneous Mapping: Enables mapping of up to 8 network cables concurrently.

Pack of 8 Jonard Tools RJ45 Cable Identifiers

Image: A set of eight numbered RJ45 cable identifiers, designed for use with the CM-100 Cable Mapper Pro.

Aufstellen

Ensure CM-100 is Ready: Verify that your Jonard Tools CM-100 Cable Mapper Pro is powered on and functioning correctly. Refer to the CM-100 manual for its specific setup instructions.
Connect Identifiers: Plug each CM-RJ45/8 identifier into the RJ45 ports of the network cables you wish to map. For example, if you are mapping cables from a patch panel, connect one identifier to each cable's end at the patch panel.
Prepare Remote End: At the remote end of the cable run (e.g., wall plate), ensure the CM-100 Cable Mapper Pro is ready to receive the signal.

Jonard Tools RJ45 Cable Identifier plugged into a wall plate

Image: A numbered RJ45 cable identifier inserted into a network wall plate, demonstrating its application for port identification.

Bedienungsanleitung

Follow these steps to use the CM-RJ45/8 identifiers with your CM-100 Cable Mapper Pro:

Connect CM-100: Connect the main unit of the CM-100 Cable Mapper Pro to the network cable at the testing location (e.g., the switch end or the other end of the cable run).
Test starten: On the CM-100, select the appropriate test mode for RJ45 cable mapping. The CM-100 will send a signal through the cable.
Identify Cable: The CM-100's display will show the identifier number corresponding to the cable it is connected to. This allows you to quickly match the remote end of the cable to its numbered identifier.
Repeat for All Cables: Repeat the process for each cable connected to an identifier until all desired cables are mapped.

Hand holding Jonard Tools CM-100 Cable Mapper Pro connected to a network cable in a server rack

Image: A technician using the CM-100 Cable Mapper Pro to test a network cable connected within a server rack, demonstrating cable mapping in a live environment.

Jonard Tools CM-100 Cable Mapper Pro connected to a network cable with an identifier

Image: The CM-100 Cable Mapper Pro connected to a network cable, with an RJ45 identifier visible, illustrating the compatibility and function of the system.

Wartung

Reinigung: Keep the identifiers clean and free from dust and debris. Use a soft, dry cloth for cleaning. Avoid abrasive cleaners or solvents.
Lagerung: Store the identifiers in a cool, dry place, away from direct sunlight and extreme temperatures. Keep them in their original packaging or a protective case to prevent damage.
Inspektion: Periodically inspect the RJ45 connectors for any signs of wear, bent pins, or damage. Replace any damaged identifiers to ensure accurate testing.

Fehlerbehebung

Problem	Mögliche Ursache	Lösung
CM-100 does not detect identifier.	Identifier not fully inserted. Damaged identifier. Cable fault (open, short). CM-100 not in correct test mode.	Ensure identifier is securely seated in the RJ45 port. Try a different identifier. Test the cable for faults using the CM-100's primary functions. Verify the CM-100 is set to the correct mapping or identification mode.
Incorrect identifier number displayed.	Multiple identifiers connected to the same cable. Identifier malfunction.	Ensure only one identifier is connected to each cable being tested. Try a different identifier to confirm if the issue is with the identifier itself.

Technische Daten

Modell: CM-RJ45/8
Kompatibilität: Jonard Tools CM-100 Cable Mapper Pro
Steckertyp: RJ45
Kabeltyp: Ethernet
Number of Identifiers: 8 (numbered 1-8)
Dimensions (per identifier): Ungefähr 1.5 x 0.75 x 1.5 Zoll
Gewicht (Gesamtbausatz): Ungefähr 0.81 Unzen
Farbe: Clear with blue accents

Garantie und Support

For information regarding warranty coverage, technical support, or replacement parts for your Jonard Tools CM-RJ45/8 RJ45 Cable Identifiers, please refer to the documentation provided with your CM-100 Cable Mapper Pro or visit the official Jonard Tools website. Specific warranty details for this accessory are typically covered under the main CM-100 product warranty.

Offiziell WebWebsite: www.jonard.com

	Bedienungsanleitung für den Multifunktions-Kabelfernsehtester CTV-8K \| Jonard Tools Ausführliche Bedienungsanleitung für den Jonard Tools CTV-8K Multifunktions-Kabelfernsehtester mit detaillierten Informationen zu Funktionen, Bedienung, Spezifikationen und Sicherheitshinweisen für Installateure und Techniker.
	Jonard Tools CTV-8K Multifunktions-Kabelfernsehtester – Bedienungsanleitung Ausführliche Bedienungsanleitung für den Jonard Tools CTV-8K Multifunktions-Kabelfernsehtester mit detaillierter Beschreibung der Funktionen, der Bedienung und der Spezifikationen für IP-Kameratests, Netzwerkdiagnose und Kabelanalyse.
	Jonard Tools CTV-8K Multifunktions-Kabelfernsehtester – Bedienungsanleitung Ausführliche Bedienungsanleitung für den Jonard Tools CTV-8K Multifunktions-Kabelfernsehtester. Diese Anleitung beschreibt detailliert die Funktionen, die Bedienung, Sicherheitsvorkehrungen und Spezifikationen für die Prüfung von IP-, Analog- und HD-Koaxialkameras sowie von PoE-, HDMI- und verschiedenen Netzwerkdiagnosefunktionen.
	Jonard Tools RJ11-100 Pass-Through Connectors: Installation Instructions Detailed, step-by-step instructions for using Jonard Tools RJ11-100 Pass-Through Connectors to terminate telephone cables. Includes product overview and company contact information.
	Jonard Tools FPM-55 Optisches Leistungsmessgerät – Bedienungsanleitung Ausführliche Bedienungsanleitung für das optische Leistungsmessgerät Jonard Tools FPM-55 mit detaillierten Informationen zu Funktionen, Spezifikationen, Bedienung, wichtigsten Merkmalen, Fehlerbehebung und Garantiebestimmungen.
	Datenblatt für Schlitz- und Ringwerkzeuge mittlerer Spannweite von Jonard Tools – MS-526, MS-446, MS-426, MS-326, MS-316, MS-306, MS-6, MS-26, MS-336 Detailliertes Datenblatt für die patentierten Mid Span Slit & Ring Tools von Jonard Tools für effizienten und sicheren Zugang zu Glasfaserkabeln. Enthält Spezifikationen, Gebrauchsanweisungen und Ersatzteile für die Modelle MS-526, MS-446, MS-426, MS-326, MS-316, MS-306, MS-6, MS-26, MS-336 und MS-600.