BEZGAR RC Boat Accessories Package for TX2P1 Instruction Manual

1. Einleitung

This instruction manual provides essential information for the proper use, installation, and maintenance of your BEZGAR RC Boat Accessories Package, specifically designed for the TX2P1 RC Boat. Please read this manual thoroughly before using the accessories to ensure optimal performance and longevity.

2. Packungsinhalt

Your BEZGAR RC Boat Accessories Package for TX2P1 includes the following items:

• 7.4V 1200mAH Li-ion Battery x 1
• Ladekabel x 1
• Screw Propeller x 2
• Protective Silicone Gel x 2
• Ruder x 1

Image: Contents of the BEZGAR RC Boat Accessories Package for TX2P1, including a 7.4V 600mAh Li-ion battery, two screw propellers, two protective silicone pieces, and a rudder.

3. Einrichtung und Installation

These accessories are designed for the BEZGAR TX2P1 RC Boat. Refer to your TX2P1 boat's main instruction manual for specific boat disassembly/assembly steps if needed.

3.1. Einlegen der Batterie

1. Ensure the TX2P1 RC boat is powered off and dry.
2. Locate and open the battery compartment on the boat.
3. Carefully connect the 7.4V 1200mAH Li-ion Battery to the boat's power connector.
4. Place the battery securely within the compartment and close the cover, ensuring it is properly sealed to prevent water ingress.

3.2. Propellermontage

1. Identify the propeller shaft at the rear of the boat.
2. Align a new Screw Propeller with the shaft and push it firmly into place.
3. Secure the propeller with any provided retaining hardware (e.g., nut, washer) as per your boat's design.

3.3. Ruderinstallation

1. Locate the rudder mounting point at the stern of the boat.
2. Attach the Rudder to the designated slot or mechanism.
3. Ensure the rudder is securely fastened and moves freely without obstruction.

3.4. Protective Silicone Gel Installation

1. These silicone pieces are designed to protect vulnerable areas of the boat.
2. Identify the areas on your TX2P1 boat where protective silicone can be applied (e.g., bow, sides).
3. Adhere or attach the Protective Silicone Gel pieces firmly to these areas for added impact protection.

4. Bedienungsanleitung

Once accessories are installed, refer to your BEZGAR TX2P1 RC Boat's main manual for detailed operating procedures. The following videos demonstrate general RC boat operation and features that your TX2P1 boat may share.

5. Wartung

5.1. Batteriepflege

• Always use the provided Charging Cable to charge the Li-ion Battery.
• Überladen oder entladen Sie den Akku nicht.
• Lagern Sie Batterien an einem kühlen, trockenen Ort, geschützt vor direkter Sonneneinstrahlung und extremen Temperaturen.
• Disconnect the battery from the boat when not in use.

5.2. Allgemeine Reinigung

• After each use, especially in saltwater, rinse the boat and accessories with fresh water.
• Dry all components thoroughly before storage to prevent corrosion.
• Inspect propellers and rudder for any debris or damage regularly.

6. Fehlerbehebung

If you encounter issues, please refer to the TX2P1 RC Boat's main manual for comprehensive troubleshooting. Below are general tips related to the accessories:

• Akku wird nicht aufgeladen: Ensure the charging cable is properly connected to both the battery and a power source. Check for any damage to the cable or battery.
• Verminderte Leistung: Check the battery charge level. Inspect propellers for damage or entanglement with debris.
• Loose accessories: Periodically check that all installed accessories (propellers, rudder, protective silicone) are securely attached.

7. Spezifikationen

8. Garantie und Support

BEZGAR stands by the quality of its products. While specific warranty details for this accessories package are not provided in this document, we are committed to customer satisfaction.

If you have any questions, concerns, or require assistance with your BEZGAR RC Boat Accessories Package for TX2P1, please do not hesitate to contact us. Our customer support team is ready to help.